LEGALDIGMLEGALDIGM
    ← Canada
    Beta
    SOR-90-97:en

    SOR-90-97:en — Coal Mining Occupational Health and Safety Regulations

    Beta. Legal information, not legal advice. LEGALDIGM is not a law firm. Check the official source for the current text.

    Analyze this law with AI
    1 [Repealed, SOR/2002-143, s. 2] 2 In these Regulations, Act means Part II of the Canada Labour Code; (Loi) appointed means, in respect of a coal mine, appointed in writing by the mine manager; (nommé) authorized means, in respect of a coal mine, authorized in writing by the mine manager; (autorisé) auxiliary fan means a fan that is used for secondary ventilation in an underground portion of a coal mine which cannot be ventilated by the main fan or a booster fan without separate mechanical devices; (ventilateur secondaire) blasting machine means a device that is designed for use in a coal mine and that provides an electrical impulse to explode an electrical detonator; (exploseur) booster fan means a fan that is situated underground and is used in conjunction with a main fan to assist in the primary ventilation of a coal mine; (ventilateur d’appoint) breaking strength means, with respect to a hoist rope, the minimum static load applied to the rope that causes the rope to fail in tension; (charge de rupture) certificate means a certificate of competency issued on the recommendation of the Provincial Board; (certificat) chief electrician means a mine electrician who holds a first class certificate as a mine electrician and who is appointed to supervise all other mine electricians in a coal mine; (électricien en chef) chief mechanic means a mine mechanic who is appointed to supervise all other mine mechanics in a coal mine; (mécanicien en chef) coal miner means an employee who holds a certificate as a coal miner and who is appointed to work underground at cutting, shearing, breaking or otherwise loosening coal or stone from a working face; (mineur de charbon) designated means, in respect of a coal mine, designated in writing by the mine manager; (désigné) district office means, in respect of a coal mine, the district office of the Department of Labour that is (a) closest to the coal mine, and (b) in the administrative region of that Department in which the coal mine is situated; (bureau de district) electrical equipment means equipment for the generation, distribution or use of electricity; (équipement électrique) engineer means an engineer who is licensed to practise in the Province of Nova Scotia; (ingénieur) explosive does not include a detonator; (explosif) factor of safety means, in respect of equipment, the number of times the breaking strength of the equipment is greater than the maximum load for which the equipment is designed; (facteur de sécurité) first aid certificate means a certificate issued by the St. John Ambulance or the Canadian Red Cross Society following the successful completion of a two-day first aid course; (certificat de secourisme) flameproof means, in respect of electrical equipment, that the equipment is in an enclosure that is capable of (a) withstanding, without damage, an explosion that may occur within the enclosure of any mixture of methane gas and air, and (b) preventing ignition of any mixture of methane gas and air surrounding the enclosure from sparks or flames from the explosion of such a mixture within the enclosure; (antidéflagrant) intrinsically safe means, in respect of electrical equipment, that any spark or thermal effect in any part of the electrical equipment and its interconnecting wiring is not capable of causing the ignition of any mixture of methane gas and air; (intrinsèquement sûr) locked out means, in respect of any equipment, machine or device, that the equipment, machine or device has been rendered inoperative and cannot be operated or energized without the consent of the person who rendered it inoperative; (verrouillé) main fan means a fan that is situated above ground at a coal mine and is used for primary ventilation in the coal mine; (ventilateur principal) man car means a vehicle that is used underground to transport persons along a fixed rail, track or trolley beam; (wagonnet de transport des personnes) material car means a vehicle that is used underground to transport material or equipment along a fixed rail, track or trolley beam; (wagonnet de transport du matériel) maximum authorized load means, in respect of a hoist, the maximum static load that the hoist may carry without the factor of safety of the hoist rope being reduced; (charge maximale autorisée) meeting station means a meeting station designated under subsection 40(2); (poste de rassemblement) mine car means a man car or a material car; (wagonnet de mine) mine electrician means an employee who holds a first or second class certificate as a mine electrician and who is appointed as a mine electrician; (électricien de mine) mine examiner means an employee who holds a certificate as a mine examiner and who is appointed as a mine examiner; (inspecteur de mine) mine manager means, in respect of a coal mine, an employee who holds a first class certificate as a mine official and is employed by the employer as the manager of the mine pursuant to a written contract; (directeur de mine) mine mechanic means an employee who holds a first or second class certificate as a mine mechanic, including an employee who holds a stationary engineer’s certificate issued before April 1, 1986, and who is appointed as a mine mechanic; (mécanicien de mine) mine rescue station superintendent means a mine rescue worker who holds a certificate as a mine examiner and who is appointed as a mine rescue station superintendent under paragraph 151(2)(b); (surintendant de station de sauvetage) mine rescue team captain means a mine rescue worker who holds a certificate as a mine examiner and who is appointed as a mine rescue team captain under paragraph 151(2)(a); (capitaine d’équipe de sauvetage) mine rescue worker means an employee who holds (a) a certificate in mine rescue work and first aid to the injured, and (b) a first aid certificate; (sauveteur minier) mine surveyor means an employee who holds a certificate as a mine surveyor and who is appointed as a mine surveyor; (arpenteur minier) overman means an employee who holds a third class certificate as a mine official and who is appointed as an overman; (maître mineur) Provincial Board means the Board of Examiners appointed under subsection 4(1) of the Coal Mines Regulation Act, R.S.N.S. 1967, c. 36; (Commission provinciale) qualified person means, in respect of a specified duty, an employee who, because of the employee’s knowledge, training and experience, is qualified to perform that duty safely and properly; (personne qualifiée) rope-testing laboratory means a laboratory set out in Schedule I; (laboratoire d’essais de câbles) shaft includes a slope, incline or pit; (puits) shot means an explosive charge that has been placed in a shot hole; (coup de mine) shotfirer means an employee who holds a certificate as a mine examiner and who is appointed as a shotfirer; (tireur de mine) trip means a mine car or mine cars that are connected together; (convoi) underground manager means an employee who holds a second class certificate as a mine official and who is appointed as an underground manager; (directeur de fond) vertical shaft means a shaft that has an inclination greater than 45° from the horizontal; (puits vertical) working face means a location underground from which coal or stone is cut, sheared, broken or otherwise loosened; (front de taille) working shaft means a shaft through which employees, coal or materials are normally transported. (puits d’exploitation) 3 These Regulations apply in respect of coal mines subject to the Act. 4 (1) Every record, report, plan or procedure referred to in these Regulations, or any copy thereof, shall be kept by the employer above ground at the coal mine in respect of which it applies (a) in such a manner that it is readily available for examination by a safety officer and by the safety and health committee or the safety and health representative for the work place in respect of which it applies; and (b) subject to subsections 69(5) and 143(6), for a period of at least two years after the last entry therein. (2) Every record, report, plan or procedure referred to in these Regulations shall be dated and signed by the person who made the record, report, plan or procedure. (3) In addition to the requirements of subsection (2), every plan referred to in these Regulations shall be countersigned by the mine manager of the coal mine in respect of which the plan applies. 5 Where the employer submits plans or procedures in respect of a coal mine to the Coal Mining Safety Commission for approval, the employer shall (a) without delay after the submission, notify the safety and health committee or the safety and health representative in writing of the submission; and (b) keep a copy of the approved plans or procedures readily available at the coal mine for examination by the employees. 6 In the event of an inconsistency between any standard incorporated by reference in a provision of these Regulations and any other provision of these Regulations, that other provision shall prevail to the extent of the inconsistency. 7 Before an employee is employed in a position of mine manager or is appointed to a position of underground manager or overman, the employee shall have obtained the qualifications required for all positions junior to that position. 8 (1) The employer shall employ a separate mine manager for each coal mine. (2) Subject to subsection (3), where a mine manager dies, resigns or is otherwise permanently prevented from discharging the responsibilities of mine manager, the employer shall (a) identify in writing a person who holds a first class certificate as a mine official to perform the duties of the mine manager; (b) identify in writing an underground manager to perform the duties of the mine manager; or (c) stop the operation of the mine. (3) Within 90 days after an identification made under paragraph (2)(b), the employer shall comply with paragraph (2)(a) or (c). 9 Every coal mine shall be under the daily supervision of at least one underground manager and one overman. 10 No explosive or detonator, other than an explosive or detonator set out in Schedule II, shall be used in a coal mine. 11 (1) No explosive or detonator shall be stored underground in a coal mine. (2) Explosives and detonators that are intended for use underground shall be stored in a structure above ground that has been approved by the Coal Mining Safety Commission. (3) The maximum quantity of explosives and detonators that are stored in accordance with subsection (2) shall be not more than the quantity required for use underground during the 24-hour period immediately following its storage. (4) Detonators shall be stored separately from explosives in a room that has a wall of masonry not less than 150 mm thick between it and any room in which explosives are stored. 12 (1) All explosives and detonators that are transported underground, other than explosives and detonators referred to in subsection 28(3) or 29(4), shall be in secure cases or canisters with the detonators in separate cases or canisters from the explosives. (2) No case or canister referred to in subsection (1) shall contain more than 5 kg of explosive unless approval for the transportation of the explosive in bulk has been given by the Coal Mining Safety Commission. 13 (1) Every employee who receives, transports or uses explosives or detonators shall return any explosive or detonator that is not used during the employee’s shift to the surface structure in which it had been stored. (2) Where an explosive or detonator is transported underground, it shall be kept in its secure case or canister until it is used. (3) Subject to subsection (4), each case or canister referred to in subsection (2) shall be kept separate from every other case or canister and from all equipment that is likely to cause the ignition of the explosive or the detonator, by as great a distance as is practicable in the area where the explosive or detonator is kept. (4) The distance referred to in subsection (3) shall be not less than 300 mm. 14 (1) A qualified person shall have control of the storage, issue and receipt of all explosives and detonators. (2) The qualified person referred to in subsection (1) shall (a) test each detonator for electrical continuity before issuing it; (b) issue detonators to no person other than a shotfirer; and (c) receive and store unused explosives and detonators returned from underground. 15 (1) A qualified person shall, at least once every three months, clean and thoroughly overhaul all blasting machines that are in service. (2) A record of the work performed pursuant to subsection (1) shall be made by the qualified person who performed the work. 16 (1) No person other than a shotfirer shall fire a shot. (2) No shotfirer shall fire a shot unless the shotfirer has been authorized to fire that type of shot. 17 The handling of explosives and detonators in the preparation underground of a shot or shot hole shall be under the direct supervision and control of a shotfirer. 18 Where shotfiring is to be done underground during a shift, the shotfirer shall verify that no more explosives or detonators than are required for the shotfiring are kept in the danger area referred to in paragraph 22(1)(a) in which the shotfiring is to be done. 19 (1) A shotfirer shall use (a) only one class, grade or quality of explosive in a shot; (b) an explosive that is in its original wrapping; (c) no more explosive in any shot hole than the amount that is necessary for the work to be performed or the maximum amount of that type of explosive that is set out in column II of Part I of Schedule II, whichever is the lesser; (d) tamping rods and stemmers that are constructed of non-metallic materials; and (e) a cleaner and crack detector that is capable of cleaning the full length of the shot hole and detecting transverse and longitudinal cracks of 3 mm or more in the shot hole. (2) No shot shall be fired (a) in broken coal or in a support pillar; or (b) in an area where the concentration of flammable gas in the air exceeds 1.25 per cent. (3) Every coal-cutting machine shall be stopped before shots are fired at the return brushing face in a longwall section. 20 Before initiating the preparations for charging a shot hole referred to in section 21, a shotfirer shall verify that all broken coal is removed from the area of the shot hole and shall allow sufficient time for dust in the air to settle. 21 A shotfirer shall, immediately before charging a shot hole underground, (a) subject to subsection 27(3), verify, using a methanometer and a locked-flame safety lamp, that the concentration of flammable gas in the general body of the air in the area of the shot hole and in any area contiguous thereto does not exceed 1.25 per cent; (b) examine the shot hole to verify that it has been thoroughly cleaned; (c) verify that the shot hole does not intersect any cracks or crevices greater than 3 mm; (d) verify that the shot hole is at least 3 mm larger than the diameter of the cartridge of the explosive to be used; (e) place a plug of stemming in the back of the shot hole; and (f) verify that any dust in the area of the shot hole has been treated with stone dust to a minimum of three 25 kg bags of stone dust per metre of advance. 22 (1) Before firing a shot, a shotfirer shall (a) determine a danger area that extends at least 30 m from the shot hole; (b) evacuate all persons from the danger area; and (c) post sentries at the limits of the danger area. (2) The sentries referred to in paragraph (1)(c) shall prevent any person, other than the shotfirer, from entering the danger area until the shotfirer verifies that the area is safe to enter. (3) No person, other than a shotfirer, shall enter the danger area referred to in subsection (1) until the person has been informed by the shotfirer or a sentry that it is safe to do so. 23 Immediately before firing a shot, a shotfirer shall repeat the test referred to in paragraph 21(a). 24 Where a shot or round of shots is fired, the shotfirer shall make an examination of the effect of the shot or round of shots before the next shot or round of shots is fired. 25 (1) Where a shot is to be fired with a blasting machine, the shotfiring cable shall be not less than 30 m long. (2) No person, other than a shotfirer, shall connect a shotfiring cable to detonator wires or to a blasting machine. (3) Where a shot is to be fired with a blasting machine, the shotfirer shall, in the following sequence, (a) twist the ends of the shotfiring cable together at the blasting machine and isolate them from ground; (b) check the shotfiring cable and the detonator circuit; (c) connect the shotfiring cable to the shot; (d) check the total circuit; (e) verify that all persons in the danger area referred to in paragraph 22(1)(a) have been evacuated from that area; (f) connect the shotfiring cable to the blasting machine, verifying that the shotfirer alone has possession and control of the blasting machine; (g) shout “FIRE” or “TIR”; (h) verify that the danger area referred to in paragraph 22(1)(a) is clear of persons; (i) take cover outside the danger area referred to in paragraph 22(1)(a); (j) fire the shot; (k) subject to sections 28 and 29, wait at least five minutes before the shotfirer returns to the area of the shot hole to satisfy himself that no dangerous condition has resulted from firing the shot; and (l) measure the concentration of flammable gas in the general body of the air in the area of the shot hole. 26 Subject to section 27, each shot hole shall be charged separately and each shot shall be fired singly. 27 (1) Subject to subsections (2) to (4), rounds of shots may be fired in shafts, development drivages, cross-measure drivages, intake and return brushings of longwall faces and repair brushings. (2) Not more than 12 shots in a round may be fired simultaneously using the shortest millisecond-delay detonators. (3) A round of shots using different millisecond-delay detonators shall not be fired unless (a) the concentration of flammable gas in the general body of the air in the area of the shot holes and in any area contiguous thereto does not exceed (i) where the period between the detonation of the first shot and the detonation of the last shot is calculated not to exceed 0.2 second, 1 per cent, and (ii) where the period between the detonation of the first shot and the detonation of the last shot is calculated to exceed 0.2 second but not to exceed 0.75 second, 0.8 per cent; (b) the mine manager has issued to the shotfirer for each area of firing a copy of the shotfiring pattern that shows (i) the position and direction of every shot hole in the round, (ii) the maximum quantity of explosive to be used in each shot hole, and (iii) the maximum length of each shot hole; and (c) the maximum period that may elapse between the detonation of the first shot and the detonation of the last shot is (i) where the shots are fired in a development drivage that contains no seam of coal exceeding 300 mm and that is more than 5 m from a waste or fault, 0.75 second or less, and (ii) in all other cases, 0.2 second or less. (4) A copy of the shotfiring pattern for each area at which multi-shot firing is carried out in a mine shall be kept available above ground at the coal mine for examination by employees. 28 (1) Where a single shot misfires, the shotfirer shall, in the following sequence, (a) remove the handle or key from the blasting machine and disconnect the blasting machine from the shotfiring cable; (b) twist the ends of the shotfiring cable together at the blasting machine and isolate them from ground; (c) wait 15 minutes; (d) examine the shotfiring cable and connections for any defects and remedy any that are found; and (e) make a further attempt to fire the shot using either the same blasting machine or another blasting machine that is suitable for the purpose. (2) Where the attempt to fire the shot referred to in paragraph (1)(e) fails, the shotfirer shall, in the following sequence, (a) remove the handle or key from the blasting machine and disconnect the blasting machine from the shotfiring cable; (b) twist the ends of the shotfiring cable together at the blasting machine and isolate them from ground; (c) wait 15 minutes; (d) mark the location of the detonator lead wires of the misfired shot; (e) cause a new shot hole to be drilled at a distance of not less than 300 mm from the loaded shot hole and parallel to and equal in depth to that shot hole; and (f) fire a shot in the newly drilled shot hole. (3) A shotfirer shall wait for five minutes after firing the shot referred to in paragraph (2)(f) and then, where practicable, sort the debris by hand, recover all explosives and detonators from the debris and take them to the structure referred to in subsection 11(2). 29 (1) Where all of a round of shots misfire, the shotfirer shall, in the following sequence, (a) remove the handle or key from the blasting machine and disconnect the shotfiring cable from the blasting machine; (b) twist the ends of the shotfiring cable together at the blasting machine and isolate them from ground; (c) wait 15 minutes; (d) test the circuit for electrical continuity; and (e) if the test shows that there is electrical continuity, attempt to fire the round using either the same blasting machine or another blasting machine that is suitable for the purpose. (2) Where the test referred to in paragraph (1)(e) shows that there is no electrical continuity, or where the attempt referred to in that paragraph fails, the shotfirer shall, in the following sequence, (a) remove the handle or key from the blasting machine and disconnect the shotfiring cable from the blasting machine; (b) twist the ends of the shotfiring cable together at the blasting machine and isolate them from ground; (c) wait 15 minutes; (d) disconnect the shotfiring cable and detonator lead wires at each shot hole; (e) test for electrical continuity in the shotfiring cable and detonator lead wires; (f) test the blasting machine; and (g) if the tests show that there is electrical continuity, the detonator lead wires and the shotfiring cable shall be reconnected and tested for electrical continuity and a further attempt shall be made to fire the round. (3) Where any of the tests referred to in paragraphs (2)(e) to (g) do not produce the desired result, the shotfirer shall install barricades and post a warning sign in accordance with subsection 31(1). (4) Where a single shot in a round misfires and is recovered, or where a part of a round of shots misfires and is recovered, the shotfirer shall sort the debris by hand, recover all explosives and detonators from the debris and take them to the structure referred to in subsection 11(2). 30 (1) Where a single shot in a round misfires and is not recovered, the procedures set out in subsections 29(1) and (2) shall be carried out. (2) Where a part of a round of shots misfires and is not recovered, the procedures set out in subsection 29(2) shall be carried out and groups of shots with the same millisecond-delay shall be fired in turn, in increasing order of delay. 31 (1) Where a misfired shot is not recovered, the shotfirer shall cause (a) barricades to be installed to prevent persons from entering the danger area for the shot hole determined in accordance with paragraph 22(1)(a); and (b) a warning sign to be conspicuously posted on each barricade referred to in paragraph (a) with the words “MISFIRED SHOT — KEEP OUT” and “COUP DE MINE RATÉ — ENTRÉE INTERDITE”. (2) After having carried out the procedures set out in subsection (1), the shotfirer shall report orally to the underground manager or mine manager the misfired shot and the procedures carried out. 32 (1) Where a shot flames on firing, the shotfirer shall, in the following sequence, (a) immediately take steps to extinguish the flame; (b) verify that the section of the coal mine in which the shot was fired is guarded by an employee and left unworked, except for making the section safe, until inspected by a safety officer; (c) without delay, report the flamed shot orally to the shotfirer’s supervisor or the underground manager; and (d) report the flamed shot in writing to the mine manager. (2) Where a mine manager is informed of a flamed shot in accordance with paragraph (1)(d), the mine manager shall, without undue delay, make a report of the flamed shot to a safety officer at the district office. 33 (1) At the end of a shotfirer’s shift, the shotfirer shall report in writing to the shotfirer’s immediate supervisor every misfired shot and flamed shot for which the shotfirer was responsible during the shift. (2) Where an immediate supervisor is informed of a misfired shot or flamed shot in accordance with subsection (1), the supervisor shall, without undue delay, report in writing to the underground manager or mine manager the misfired shot or flamed shot. 34 (1) At the end of a shotfirer’s shift, the shotfirer shall record in a book that is kept for that purpose all the shots the preparation and firing of which the shotfirer was responsible for during the shift. (2) The record referred to in subsection (1) shall include (a) the number of detonators used; (b) the amount of explosive used, expressed in grams; (c) in respect of each shot or round of shots, (i) the time of firing of the shot or round of shots, (ii) the concentration of flammable gas in the air before and after each shot or round of shots was fired, (iii) the number of detonators used, and (iv) the amount of explosive used, expressed in grams; (d) the number of misfired shots and whether they were recovered; and (e) the number of flamed shots. 35 (1) The mine manager shall, in respect of each underground portion of a coal mine, (a) develop for employees procedures for the safe entry to, exit from and occupancy of that portion; (b) develop emergency procedures that include (i) an emergency evacuation plan, (ii) a description of the procedures to be followed, (iii) the location of the emergency equipment provided by the employer, and (iv) an up-to-date plan of the coal mine; and (c) develop and implement safe operating procedures for each employee occupation. (2) The employer shall keep a copy of the procedures referred to in subsection (1) readily available for examination by employees at the coal mine in respect of which the procedures apply. (3) The employer shall instruct and train all employees in the procedures referred to in paragraphs (1)(a) and (b). 36 (1) The employer shall provide every person granted access to an underground portion of a coal mine with an electric safety lamp. (2) The employer shall provide every person who carries out an inspection that is required to be carried out under these Regulations by a person who holds a certificate as a mine examiner with a locked-flame safety lamp. 37 Not more than 15 persons shall be present at one time in a place underground, unless there are at least two separate means of exit to the surface. 38 (1) Subject to subsection (2), no person shall excavate a shaft at a distance of less than 30 m from another shaft. (2) A shaft may be connected to another shaft by a passageway if the passageway is not less than 1.2 m in width and 1.2 m in height. 39 (1) A qualified person shall, every day, inspect (a) the vertical shafts by which employees descend or ascend in a coal mine; and (b) all shaft equipment that is used in the transportation system for employees in the vertical shafts. (2) The qualified person referred to in subsection (1) shall make a written report of the inspection in a book kept for that purpose. 40 (1) A mine manager shall define on a plan, on a scale of not less than 1:10,000, the limits of each section of the mine for which an overman is responsible in such a manner that (a) every working face, other than an area where work is being carried out for the purpose of repairing or enlarging a roadway, is included within a section; and (b) the section is of a size that permits a pre-shift inspection to be completed in two hours or less. (2) A mine manager shall designate a meeting station that is located at the entrance to each overman’s section referred to in subsection (1) and shall (a) mark each meeting station clearly on the plan; and (b) cause a notice to be posted at each meeting station identifying it as a meeting station. (3) No person, other than a person carrying out an inspection or a person accompanying that person, shall pass beyond a meeting station referred to in subsection (2) unless (a) the section has been inspected and reported to be safe by the person who carried out the inspection referred to in subsection 41(1); and (b) the person is instructed to pass beyond the meeting station by the overman responsible for the section. (4) No overman shall instruct any person to pass beyond the meeting station of the section for which the overman is responsible unless the overman has information indicating that it is safe to pass beyond the meeting station. 41 (1) Every overman’s section shall be inspected by a mine examiner within the four-hour period preceding the beginning of work by each shift in that section. (2) Where there are persons present in an overman’s section, a mine examiner shall carry out the inspections of that section at intervals not exceeding eight hours. 42 (1) Every overman who is responsible for a section shall inspect every part of the section at least once during every shift at such times that no place at which an employee works remains uninspected by the overman for more than four hours after the timewhen the shift of that employee began work in that section. (2) The inspection referred to in subsection (1) shall be carried out to ascertain the conditions in relation to ventilation, strata control and general safety. (3) At least once during every shift, a mine examiner shall inspect every part of the overman’s section that is allotted to the mine examiner for inspection purposes. 43 (1) At the beginning of every shift and at least once during every shift, a mine examiner shall inspect the following places that are not included in an overman’s section: (a) every place at which mineral is being worked for repairing or enlarging a roadway; (b) every place from which machinery, equipment, tools or supports are being removed or salvaged; and (c) every place at which employees may work and through which employees do not regularly pass. (2) A mine examiner shall inspect (a) every roadway or place through which employees regularly pass, at intervals not exceeding 24 hours; and (b) every airway, at least once per week. 44 (1) Every overman or mine examiner who carries out an inspection under any of sections 41 to 43 shall, in the course of the inspection, (a) inspect the machinery and equipment; (b) report to the underground manager any machinery or equipment found by the employee to be unsafe; and (c) post at the appropriate meeting station a record of the report referred to in paragraph (b). (2) No person shall use any machinery or equipment that is the subject of a record referred to in paragraph (1)(c) until such time as it has been reported to be safe. 45 (1) Every mine examiner who carries out an inspection referred to in section 41 or subsection 42(2) shall make a report of the inspection in a book kept for that purpose, including (a) the state of the roof support; (b) the state of the ventilation and all matters affecting ventilation; (c) the concentration of flammable gases; and (d) any thing or circumstance that is likely to be hazardous to the safety or health of employees. (2) Every overman or mine examiner who carries out an inspection referred to in subsection 42(1) or section 43 shall make a report of the inspection in a book kept for that purpose, including all information relevant to the safety or health of employees. (3) Where an inspection discloses a dangerous condition in an underground portion of a coal mine, the employee who carried out the inspection shall forthwith report the condition to the overman who is responsible for that portion of the coal mine or to the underground manager. 46 (1) Where an overman who is responsible for an underground portion of a coal mine becomes aware of a dangerous condition in that portion of the coal mine, the overman shall (a) evacuate all persons, other than an employee referred to in subsection (3), from the portion affected by the dangerous condition; (b) post a sign in a conspicuous place as close as possible to the dangerous condition but outside the danger area created by the dangerous condition, to warn persons of the dangerous condition; and (c) report the existence of the dangerous condition orally to the mine manager or the underground manager. (2) Where a sign is posted in accordance with paragraph (1)(b), no person shall enter the danger area referred to in that paragraph. (3) Subsection (2) does not apply to an employee whose presence is necessary to correct the dangerous condition referred to in subsection (1). 47 (1) The employees employed in a coal mine may, for the purpose of an inspection and test for gas on behalf of the employees, be represented by any of the following persons identified by them for that purpose: (a) a person who holds a certificate as a mine examiner; and (b) two persons who belong to one of the following categories, namely, (i) two employees who are employed in the coal mine, at least one of whom holds a certificate as a mine examiner, or (ii) two persons each of whom holds a certificate as a coal miner and has at least five years’ experience of work underground in a mine from which coal is extracted, and at least one of whom holds a certificate as a mine examiner. (2) At least once every month, the employer shall permit the representatives referred to in subsection (1) to inspect every part of the coal mine, including the machinery and equipment therein, and to test for gas therein. (3) For the purposes of an inspection or test on behalf of employees, the mine manager and the employees in the coal mine shall give every assistance necessary to the representatives referred to in subsection (1). (4) The employer, the mine manager or an officer of the coal mine chosen by the employer or mine manager may accompany the representatives who carry out an inspection or test referred to in subsection (2). (5) The results of an inspection or test referred to in subsection (2) shall be reported in writing to the employer and to a safety officer at the district office. 48 Where a machine, piece of equipment, tool, fixed ladder, fixed landing or lighting system is likely to be hazardous to the safety or health of an employee, a guard or fence shall be installed for the protection of the employees. 49 Where live tests are performed on electrical equipment in an area, a guard or fence shall be installed for the protection of the employees, and no unauthorized person shall enter the area unless the electrical equipment is locked out. 50 (1) Where flammable gases are discharged from a methane drainage system in an area, a barricade shall be installed in a location where the concentration of flammable gas does not exceed 2 per cent, to prevent access to the area by unauthorized persons. (2) Warning signs shall be posted on the barricade referred to in subsection (1), indicating that access by unauthorized persons is prohibited. 51 No electricity shall be supplied or used in any part of a coal mine unless the electrical system and electrical equipment and the use thereof have been approved by the Coal Mining Safety Commission. 52 (1) The mine manager shall prepare plans, including written instructions, for the installation, inspection, testing and maintenance of all mechanical equipment, electrical equipment, machinery and tools in use in the coal mine. (2) The plans referred to in subsection (1) and any changes in those plans shall be certified by an engineer. (3) The chief mechanic shall supervise the implementation of the mechanical aspects of the plans referred to in subsection (1). (4) The chief electrician shall supervise the implementation of the electrical aspects of the plans referred to in subsection (1). (5) The mechanical work and the electrical work required by the plans referred to in subsection (1) shall be carried out by mine mechanics and mine electricians, respectively. (6) Every mine mechanic or mine electrician who carries out any work provided for in the plans referred to in subsection (1) shall make a written report of that work to the mine manager. (7) Every report referred to in subsection (6) shall be read and countersigned by the chief mechanic and the chief electrician who shall take action immediately to correct any defect that is known by or reported to either of them and that is likely to affect the safety or health of employees. 53 At least once every 24 hours of operation of a coal mine, a mine mechanic shall (a) inspect the external parts of every conveyor and belt line in use in the coal mine; and (b) make a record of the inspection referred to in paragraph (a) in a book kept for that purpose. 54 (1) Where any workings in a coal mine are advancing towards or are within 50 m of an area that contains or is likely to contain a dangerous accumulation of water or a dangerous concentration of flammable gas, the working face shall be not more than 5 m in width or 4 m in height. (2) Where any workings in a coal mine are advancing towards or are within 50 m of an area that contains or is likely to contain a dangerous accumulation of water or a dangerous concentration of flammable gas, boreholes shall be bored for the purpose of locating the dangerous accumulation of water or dangerous concentration of gas, as follows: (a) at least one borehole shall be bored near the centre of the working face (i) where the working face is not more than 2.5 m in width or height, to a depth of at least 5 m in advance of the working face, and (ii) where the working face is more than 2.5 m in width or height and not more than 5 m in width or 4 m in height, to a depth of at least 20 m in advance of the working face; (b) at least two boreholes shall be bored near each side of the working face (i) where the working face is not more than 2.5 m in width or height, to a depth of at least 3 m in advance of the working face, and (ii) where the working face is more than 2.5 m in width or height and not more than 5 m in width or 4 m in height, to a depth of at least 12 m in advance of the working face; and (c) where the seam of a working face is 3.5 m thick or more, a borehole shall be bored at an angle of not less than 20° up from the roof of the area where the working face is located (i) where the working face is not more than 2.5 m in width or height, to a depth of at least 5 m in advance of the working face, and (ii) where the working face is more than 2.5 m in width or height and not more than 5 m in width or 4 m in height, to a depth of at least 20 m in advance of the working face. (3) Where a boring referred to in subsection (2) makes contact with a dangerous accumulation of water or a dangerous concentration of flammable gas, a qualified person shall (a) report the accumulation or concentration to the overman; (b) while any work is being performed at the working face, monitor the accumulation or concentration using a locked-flame safety lamp and a methanometer; and (c) take appropriate measures to dissipate the accumulation or concentration. 55 No coal mine shall be worked below the sea bottom or below a body of water or material that may flow, except under the following conditions: (a) a solid barrier of unworked mineral of 50 m or more shall be left between the workings of a submarine lease and any other submarine lease; (b) subject to paragraph (c), where a coal seam or stratified deposit is worked, there shall be a cover of 55 m or more of solid measure; and (c) where a passageway is driven, there shall be a cover of 30 m or more of solid measure. 56 (1) At least one exploring drift shall be driven in advance of the working face of workings in a coal mine that are advancing towards an area (a) that is less than 300 m below the sea bottom or a body of water or material that may flow; and (b) where there is likely to be a geological fault at a distance of 50 m or less from the working face. (2) Where the throw or dislocation of a geological fault exceeds 10 m or where the faces of the fault plane are separated by material more than 600 mm thick, no coal face shall be worked within 11 m of that fault. (3) Where a solid measure below a sea bottom is less than 150 m, soundings shall be taken to a distance of at least 300 m in advance of any workings referred to in subsection (1) for the purpose of determining the depth of the water, and levels shall be taken at the working face at least once every three months for the purpose of determining the depth of the solid measure. (4) The location of the soundings and the levels referred to in subsection (3) shall be marked on a plan of the underground workings that is kept readily available at the coal mine in respect of which it applies for examination by employees. 57 (1) Subject to subsection (2), no person shall be employed to work as a coal miner at a working face unless the person is a coal miner. (2) A person who is not a coal miner may be employed at a working face to perform the functions of a coal miner if the person is employed for training purposes for not more than eight months and a qualified person accompanies the person, exercises close personal control over the person and provides appropriate guidance to the person in respect of safe work practices. (3) No person shall be employed at a working face to perform functions other than the functions of a coal miner unless the person has received training in the safety and health procedures to be followed. 58 Every employee whose employment in a coal mine requires that the employee be the holder of a certificate, other than a coal miner’s certificate, shall complete a refresher course, approved by the Provincial Board, within six months after the expiration of every five-year period after (a) the date of the certificate; or (b) the date of the most recent refresher course taken by the employee in respect of the certificate. 59 (1) The mine manager shall prepare in writing and implement safe procedures for the operation of cages, trips and mobile equipment underground. (2) The procedures referred to in subsection (1) shall specify the conditions under which persons may be transported. (3) The employer shall submit a copy of the procedures referred to in subsection (1) and any changes in those procedures to the Coal Mining Safety Commission for approval at least 30 days before the implementation of the procedures or changed procedures. 60 (1) Transportation underground by trips or mobile equipment shall be subject to the following conditions: (a) an electric lamp with a red light shall be affixed to the approaching end of the trip or mobile equipment; (b) switches, derails, stop blocks, frogs and other track safety devices shall be installed in a manner that provides for the safe operation of trips on the track and for the safety of employees walking in the roadway; (c) a clearance of not less than 300 mm shall be provided on one side of the trip or mobile equipment and of not less than 600 mm on the other side; (d) a clearance of not less than 300 mm shall be provided (i) above the top of any load on the trip or mobile equipment, or (ii) where the trip or mobile equipment is covered, above the top of the cover; (e) manholes shall be provided at intervals not exceeding 50 m in all roadways in which trips or mobile equipment are moved by mechanical means, other than by locomotives; (f) in all roadways in which trips or mobile equipment are moved by locomotives, the maximum interval between manholes shall be (i) 100 m in roadways that have no curve and where the gradient does not exceed 3.5 per cent, and (ii) 30 m in all other roadways and on curves; and (g) where the gradient of a roadway referred to in paragraph (e) exceeds 5.2 per cent, the employer shall set out in writing and keep at the entrance to the roadway procedures that specify the speed limits and safety control measures for trips and mobile equipment on that roadway. (2) Where a roadway that is used for transportation intersects a roadway that is used by employees, a fence shall be installed and a warning sign posted at the intersection. (3) Every manhole referred to in subsection (1) shall be (a) securely supported; (b) at least 1.3 m in depth and 0.9 m in width; and (c) 1.5 m in height or the height of the roadway, whichever is the higher. (4) Every manhole shall be located on the side of the roadway that has the greater clearance. (5) Every manhole shall be (a) kept clear of material; (b) kept free of obstacles to entry; and (c) clearly marked with an identifying number. 61 Where more than 10 employees normally use a roadway, the roadway shall be not less than 1.5 m in height and, where a conveyor is in service in the roadway, have a clearance of not less than 600 mm between one side of the conveyor and the side of the roadway. 62 Where a trip that is used by persons is operated in a roadway underground that is more than 30 m in length, a means of signalling and communication between all regular stopping places designated in the procedures referred to in subsection 59(1) and the hoist operator or the locomotive operator shall be provided. 63 (1) Every surface hoist shall be operated by a hoist operator who is a qualified person. (2) No person, other than an authorized person, shall enter a hoist room. (3) A hoist operator shall be in attendance in the hoist room at all times when a person is in an underground portion of the coal mine that is normally entered by means of a hoist. 64 (1) No hoist operator shall operate a surface hoist above ground that is used for transporting employees unless a physician has (a) examined the hoist operator (i) in the three-month period prior to the operation of the hoist, and (ii) on the hoist operator’s return to work after an illness or injury for which the hoist operator received medical attention; and (b) certified that the hoist operator is mentally and physically fit to operate a surface hoist. (2) The employer shall keep the physician’s certificate referred to in paragraph (1)(b) at the coal mine in which the hoist operator who is the subject of the certificate works. 65 (1) Every surface hoist shall meet the following standards: (a) the engine shall be installed on a concrete or other rigid foundation; (b) hoisting drums on which the rope is coiled shall be provided with flanges or horns and, where a hoisting drum is conical, with such other safety devices as will prevent the rope from slipping; (c) the hoist shall be equipped with a device that (i) clearly indicates to the hoist operator the location of the cage or trip, and (ii) where a trip may be used on more than one track, is of a type that indicates on which track the trip is being hoisted; (d) the hoist shall be equipped with a braking system that (i) stops cages or trips within the deceleration rates set out in the procedures referred to in subsection 59(1) for both the descending and ascending modes, (ii) is automatically applied in the event of a power failure, and (iii) may be applied by the hoist operator in the event of an emergency; (e) the hoist shall be equipped with an overwind preventor and a speed controller that shut off the power and apply the braking system when the cage or trip travels (i) beyond the top or bottom of the run, or (ii) at a speed in excess of the maximum speed for the cage or trip set out in the procedures referred to in subsection 59(1); (f) unless the overwind preventor and speed controller referred to in paragraph (e) are in full and fixed engagement with the hoisting engine, the overwind preventor and speed controller shall be (i) designed to be fully engaged automatically or by the hoist operator whenever persons are to be transported, and (ii) provided with an automatic device that indicates to the hoist operator and all persons responsible for the loading of the cage or trip that the overwind preventor and speed controller have been fully engaged; and (g) where used for transporting persons, the hoist shall be equipped with at least two brakes that meet the requirements of subparagraphs (d)(i) to (iii). (2) Every device referred to in paragraph (1)(c) shall be tested for effective functioning after every adjustment to the length of the hoist rope. 66 (1) During each shift, a hoist operator shall test the surface hoist, including the safety devices connected to it. (2) Where tests are performed in accordance with subsection (1), the hoist operator shall test (a) the overwind preventor to verify that the cage or trip does not travel more than 0.6 m past the top or the bottom of the run; and (b) the speed controller with the cage midway in the shaft or with the trip part of the way along the run. (3) Subject to subsection (4), where a surface hoist has not been operated for more than four hours, before persons are transported on that hoist, a trial wind shall be carried out over the lesser of (a) the complete run of the cage or trip, or (b) 400 m. (4) Except in the case of an emergency, where a surface hoist has not been operated for any period because of an accident or defect, a full trial wind shall be carried out before lowering or hoisting is resumed. (5) A qualified person shall test (a) at least once every 24 hours, the overwind preventor, speed controller and other safety devices of a surface hoist that is used only for transporting persons; (b) at least once every week, the overwind preventor, speed controller and other safety devices of a surface hoist that is used for hoisting materials; and (c) at least once every month, the braking system of every surface hoist, including the emergency brake, overwind preventor, speed controller, other safety devices and the devices referred to in paragraph 65(1)(c) and subparagraph 65(1)(f)(ii). (6) The hoist operator or qualified person who carries out the tests referred to in subsections (1) to (5) shall make a record of those tests in a book kept for that purpose. 67 At least once every 24 hours, a mine mechanic shall (a) inspect the external parts of all surface hoists, including cages, mine cars, tackling equipment, head gear, ropes, sockets, rope paths and couplings, that are in use in the coal mine; and (b) make a record of the inspection referred to in paragraph (a) in a book kept for that purpose. 68 Every hoist rope shall be made of steel and have a factor of safety of not less than six. 69 (1) No hoist rope shall be placed in service unless it has been tested for breaking strength by a rope-testing laboratory. (2) The employer shall keep, for every hoist rope, every test certificate issued in respect of the rope by a rope-testing laboratory and a certificate from the manufacturer of the rope. (3) The certificates referred to in subsection (2) shall contain the following information in respect of the hoist rope: (a) the name and address of the manufacturer; (b) the manufacturer’s rope number; (c) the date of manufacture; (d) the diameter, expressed in millimetres; (e) the mass per unit length, expressed in kilograms per metre; (f) the number of strands; (g) the class of core; (h) the percentage by mass of lubricant in the core; (i) the trade name of the interior rope lubricant; (j) the number of wires in a strand; (k) the diameter of the wires, expressed in millimetres; (l) the breaking strength of steel from which the wire is made, expressed in kilopascals; (m) the results of the standard torsion test of the wires; (n) the actual breaking strength; and (o) the extension of a test piece when tested to destruction. (4) For every hoist rope, the following information shall be recorded in a record book: (a) the name of the company from which the rope was purchased; (b) the date of purchase; (c) the manufacturer’s rope number; (d) the date on which the rope is installed in or removed from a particular location; (e) the location referred to in paragraph (d); (f) the mass of the cage or mine car in respect of which the rope is installed; (g) the maximum load for which the rope is designed; (h) the maximum length of rope in service below the sheave; (i) the maximum mass of rope in service below the sheave; (j) the factor of safety of the rope in each location where it is installed; (k) the dates on which rope samples are taken; (l) the dates and results of tests for breaking strength; and (m) where applicable, the date of permanent removal from service and the reasons therefor. (5) The employer shall keep the record book referred to in subsection (4) at the coal mine in which the rope is in service (a) during the period in which the rope is in service; and (b) during the five-year period immediately following the day on which the rope is permanently removed from service. 70 No spliced hoist rope, other than an endless hoist rope, shall be used for transporting persons. 71 (1) Where a cage or trip is at its lowest point on the run, the drum shall have remaining on it at least five turns of hoist rope. (2) The diameter of a hoist rope sheave shall be not less than (a) for a rope 25 mm or more in diameter, 80 times the rope diameter; and (b) for a rope less than 25 mm in diameter, 60 times the rope diameter. (3) Every hoist rope sheave shall be machined to fit the rope that is used on it. 72 No direct hoist rope shall be reversed on the drum of a hoist. 73 (1) Every hoist rope shall be kept lubricated. (2) The lubricant that is used on a hoist rope shall be (a) suitable for the conditions under which the rope is used; and (b) used in accordance with the recommendations of the manufacturer of the rope. 74 (1) A rope sample shall be taken at least once every month from every hoist rope in service in a coal mine, except where the rope is used in (a) an endless hoist rope system; or (b) an auxiliary hoist that is used for localized movement of material and for which no rope sample is required by the plans referred to in subsection 52(1). (2) The rope sample referred to in subsection (1) shall consist of at least 4 m of hoist rope cut from the end at which the hoist rope is attached to the cage or trip. (3) A test piece of the rope sample referred to in subsection (1) shall be (a) cut from the end of the rope sample that was attached to the cage or trip; (b) at least 2 m in length; and (c) tested by a rope-testing laboratory. (4) The ends of the rope sample referred to in subsection (1) and of the test piece referred to in subsection (3) shall be bound with soft wire to prevent them from unravelling. 75 Endless hoist ropes that are more than 19 mm in diameter or that are used to transport persons on grades exceeding 4 per cent shall be non-destructively tested at least once every three months. 76 A hoist rope shall be removed from service where (a) the extension of a test piece of the rope, when tested to destruction, has decreased to less than 60 per cent of its original extension; (b) the number of broken wires in any section of the rope that is equal to the length of one lay of the rope exceeds six; (c) marked corrosion of the rope has occurred; (d) the core of the rope is ineffectually lubricated; or (e) the breaking strength of the rope has decreased to 85 per cent of the breaking strength for the rope set out in the manufacturer’s certificate referred to in subsection 69(2). 77 (1) Detaching hooks of a hoist shall be (a) installed between the socket and safety chains on all cages; and (b) cleaned, refitted and tested by a qualified person at least once every month. (2) The detaching plate of a hoist shall be (a) placed as high as is practicable above the decking level; (b) capable of holding the mass of the cage if overwinding occurs; and (c) tested once every month by a qualified person using calipers or gauges. (3) The clearance between the head sheave and the top of a cage that is stopped at the top of the run shall be not less than 5 m. (4) The qualified person referred to in paragraph (1)(b) or (2)(c) shall record the results of the tests in a hoisting machinery record book kept for that purpose. 78 (1) All hoist ropes, other than endless hoist ropes, shall be connected to their loads by means of a socket that is designed and installed in accordance with good engineering practice. (2) Hoist ropes shall, at least once every month, be fitted with new sockets or sockets that have been cleaned and tested. (3) The drum end of a hoist rope shall be fastened to the drum by not less than two clamps. 79 (1) The connecting attachments between a newly installed or newly cut hoist rope and a cage or trip and between the hoist rope and the drum shall be inspected by a qualified person before the hoist is used. (2) No hoist rope referred to in subsection (1) shall be used for the transportation of persons in a shaft unless two trial winds have been made with the cage or trip loaded to the maximum authorized load of the hoist. (3) The trial winds referred to in subsection (2) shall be made over the lesser of (a) the complete run of the cage or trip, or (b) 1 500 m. 80 (1) The qualified person referred to in subsection 79(1) shall record the results of the inspection of the connecting attachments in the hoisting machinery record book referred to in subsection 77(4). (2) The results of the trial winds referred to in subsection 79(2) shall be recorded by the hoist operator in a hoist operator’s record book kept for that purpose. 81 Every mine car shall be so constructed that any coupling, shackle pin or safety chain is visible for inspection. 82 Effective on October 1, 1993, every mine car shall have a name-plate that indicates (a) the manufacturer’s name and address; (b) the tare weight of the fitted mine car; (c) the maximum load for which the mine car is designed, expressed (i) in the case of a material car, in tonnes, and (ii) in the case of a man car, in number of persons, calculated on the basis of 81.7 kg per person; (d) the maximum speed for which the mine car is designed, expressed in metres per second; and (e) the month and year of manufacture. 83 (1) Every man car shall be equipped with seats that are secured to the body of the man car. (2) At least one man car that is part of a trip of man cars shall be designed to transport an injured person on a stretcher. (3) The first man car of a trip shall be secured by a primary fastening arrangement that is (a) in the case of a direct hoist rope system, a rope socket; (b) in the case of an endless hoist rope system, a rope clamp; and (c) in the case of a locomotive system, a coupling. 84 (1) Where a man car is used on a gradient exceeding 4 per cent, it shall, for the purpose of coupling it with other mine cars, be equipped with (a) three continuous draw-bars made of steel; or (b) a single draw-bar composite of rolled steel sections and rolled steel plate. (2) The continuous draw-bars referred to in paragraph (1)(a) shall be (a) extended the full length of the man car; (b) securely bolted to the floor and base sills of the man car; and (c) visible for inspection. (3) Where man cars of a trip are used on a gradient exceeding 4 per cent, the man cars shall be equipped with safety brakes that are (a) interconnected and operated simultaneously with the safety brakes of the other man cars of the trip; (b) manually operable from at least one man car of the trip; (c) automatically operable by an overspeed governor on one of the man cars of the trip in the event of a 20 per cent overspeed; (d) capable of stopping the maximum load of the man car at t

    The text continues in the official source.

    Related guides, FAQ and contract templates