LEGALDIGMLEGALDIGM
    ← Canada
    Beta
    SOR-2020-258:en

    SOR-2020-258:en — Off-road Compression-Ignition (Mobile and Stationary) and Large Spark-Ignition Engine Emission Regulations

    Beta. Legal information, not legal advice. LEGALDIGM is not a law firm. Check the official source for the current text.

    Analyze this law with AI
    1 (1) The following definitions apply in these Regulations. Act means the Canadian Environmental Protection Act, 1999. (Loi) adjustable parameter means a device, a system or an element of design that is capable of being adjusted to affect the emissions or performance of an engine during emission testing or normal in-use operation, but does not include a device, a system or an element of design that is permanently sealed by the engine manufacturer or that is inaccessible using ordinary tools. (paramètre réglable) CFR means chapter I of Title 40 of the Code of Federal Regulations of the United States. (CFR) CFR 60 means subchapter C, part 60, of the CFR, as amended from time to time. (CFR 60) CFR 86 means subchapter C, part 86, of the CFR, as amended from time to time. (CFR 86) CFR 89 means subchapter C, part 89, of the CFR, as it existed on July 1, 2020. (CFR 89) CFR 94 means subchapter C, part 94, of the CFR, as it existed on July 1, 2020. (CFR 94) CFR 1039 means subchapter U, part 1039, of the CFR, as amended from time to time. (CFR 1039) CFR 1042 means subchapter U, part 1042, of the CFR, as amended from time to time. (CFR 1042) CFR 1048 means subchapter U, part 1048, of the CFR, as amended from time to time. (CFR 1048) CFR 1051 means subchapter U, part 1051, of the CFR, as amended from time to time. (CFR 1051) CFR 1054 means subchapter U, part 1054, of the CFR, as amended from time to time. (CFR 1054) CFR 1060 means subchapter U, part 1060, of the CFR, as amended from time to time. (CFR 1060) CFR 1068 means subchapter U, part 1068, of the CFR, as amended from time to time. (CFR 1068) complete fuel system means a fuel system that is attached to an engine and that consists of fuel lines and at least one fuel tank. (système complet d’alimentation en carburant) compression-ignition engine means an engine that operates as a reciprocating internal combustion engine other than an engine that operates under characteristics significantly similar to the theoretical Otto combustion cycle or uses a spark plug or other sparking device. (moteur à allumage par compression) crankcase emissions means substances that are emitted into the atmosphere from any portion of the crankcase ventilation or lubrication systems of an engine and that cause air pollution. (émissions du carter) element of design, in respect of an engine, means (a) any control system, including computer software, electronic control systems and computer logic; (b) any control system calibrations; (c) the results of systems interaction; or (d) any hardware items. (élément de conception) emergency machine means a machine that is designed (a) to be used exclusively for aircraft rescue or to fight fires at airports; (b) primarily to fight wildfires, including a vehicle that is designed to be equipped with an auxiliary fire-fighting machine; or (c) to be used exclusively in emergency situations. (machine de première intervention) emergency situation means any situation in which there is a direct or indirect risk of loss of human life. (situation d’urgence) emission control system means any device, system or element of design that controls or reduces the emissions from an engine. (système antipollution) emission family means, (a) in respect of a company’s engines that are covered by an EPA certificate, the grouping that is specified in the EPA certificate; (b) in respect of any fuel lines and fuel tanks that form part of a complete fuel system and that are covered by one or more EPA certificates, the grouping that is specified in the EPA certificates; (c) in respect of a company’s engines other than those referred to in paragraph (a), the grouping determined in accordance with, (i) in the case of mobile compression-ignition engines — other than those referred to in subparagraph (iii) — and large spark-ignition engines that meet the alternative standards referred to in section 19 of these Regulations, section 230, subpart C, of CFR 1039 and, if the engine conforms to the alternative standards referred to in section 14 of these Regulations, section 645(c), subpart G, of CFR 1039, (ii) in the case of stationary compression-ignition engines that have a per-cylinder displacement of (A) more than 10 L, section 230, subpart C, of CFR 1042 or, in the case of an engine that conforms to the alternative standards referred to in subsection 16(1) or (3) of these Regulations, section 204(a) to (c), of subpart C, of CFR 94, and (B) 10 L or less, section 230, subpart C, of CFR 1039 or, in the case of an engine that conforms to the alternative standards referred to in subsection 16(1) or (3) of these Regulations, section 116(a) to (d), of subpart B, of CFR 89, (iii) in the case of mobile compression-ignition engines that are or will be installed in recreational vehicles, section 230, subpart C, of CFR 1051, and (iv) in the case of large spark-ignition engines — other than those that meet the alternative standards referred to in section 19 of these Regulations — section 230, subpart C, of CFR 1048; or (d) in respect of any fuel lines and fuel tanks that form part of a complete fuel system other than those referred to in paragraph (b), the grouping determined in accordance with section 230, subpart C, of CFR 1060. (famille d’émissions) EPA means the United States Environmental Protection Agency. (EPA) EPA certificate means a certificate of conformity to United States federal standards issued by the EPA. (certificat de l’EPA) evaporative emissions means fuel compounds that are emitted into the atmosphere from an engine that is fuelled with volatile liquid fuel, other than exhaust emissions, crankcase emissions and smoke emissions. (émissions de gaz d’évaporation) exhaust emissions means substances emitted into the atmosphere from any opening downstream from the exhaust port of an engine. (émissions de gaz d’échappement) fire-pump engine means a stationary internal combustion engine that is certified by the National Fire Protection Association and designed to be used in emergency situations to provide power to pump water for fire suppression or prevention. (moteur de pompe à incendie) fuel line means hose, tubing and primer bulbs containing or exposed to liquid fuel — including moulded hose, tubing and primer bulbs — that transport fuel to or from an engine, excluding (a) fuel tank vent lines; (b) segments of hose or tubing in which the external surface is normally exposed to liquid fuel inside the fuel tank; and (c) primer bulbs that contain liquid fuel only for priming the engine before starting. (conduite d’alimentation en carburant) fuel tank means a tank that is equipped with a cap and designed to hold fuel. (réservoir de carburant) hazardous location means any location in which an explosive gas atmosphere — as defined in section 18-002 of the most recent version of the Canadian Standards Association standard C22.1, Canadian Electrical Code, Part 1 — is or may be present. (emplacement dangereux) large spark-ignition engine means an engine that (a) operates under characteristics significantly similar to the theoretical Otto combustion cycle; (b) uses a spark plug or other sparking device; and (c) develops more than 19 kW of power measured at the crankshaft, or its equivalent, when equipped only with standard accessories that are necessary for its operation. (gros moteur à allumage commandé) machine means anything that is powered by an engine. (machine) mobile, in respect of an engine, means any engine that is designed to be used in or on a machine that is designed to be mobile. (mobile) model year means the year, as determined under section 4, that is used by a manufacturer to designate a model of engine. (année de modèle) remote location means a geographic area that is serviced neither by (a) an electrical distribution network that is under the jurisdiction of the North American Electric Reliability Corporation or the main Newfoundland and Labrador electrical distribution networks; nor (b) a natural gas distribution network. (région éloignée) replacement engine, subject to subsection 25(4), means an engine that is manufactured to replace the engine of a machine for which no engine exists that (a) conforms to the applicable standards referred to in sections 10 to 23; (b) has the physical or performance characteristics necessary for the operation of the machine; and (c) is manufactured by the manufacturer of the original engine or the replacement engine. (moteur de remplacement) smoke emissions means substances in exhaust emissions that prevent the transmission of light. (émissions de fumée) stationary, in respect of an engine, means any engine that is designed to be used in or on a machine that is designed to be stationary. (fixe) transportation refrigeration unit means a refrigeration system that is powered by an engine — other than an engine that meets the criteria set out in any of sections 645(f)(1) to (4), subpart G, of CFR 1039 — and that is designed to control the temperature of products that are transported in rolling stock, vehicles or trailers. (dispositif frigorifique de transport) unique identification number means a number, consisting of Arabic numerals, Roman letters or both, that the manufacturer assigns to the engine for identification purposes. (numéro d’identification unique) useful life means the period of time or use in respect of which an emission standard applies to an engine, as set out in subsection 10(2), 11(3), 12(2), 13(2), 14(2), 15(2), 16(4) or 18(5), as the case may be. (durée de vie utile) volatile liquid fuel means any fuel that is a liquid at atmospheric pressure and has a Reid vapour pressure greater than 13.79 kPa. (carburant liquide volatil) (2) Standards that are incorporated by reference in these Regulations from the CFR are those expressly set out in the CFR and must be read as excluding (a) references to the EPA or its Administrator exercising discretion; (b) alternative standards or exceptions related to the averaging, banking and trading of emission credits, to small volume manufacturers or to financial hardship; and (c) standards or evidence of conformity of any authority other than the EPA. (3) For the purposes of these Regulations, a reference in the CFR to (a) “nonroad vehicle” or “nonroad equipment” is to be read as a reference to “machine”; (b) “engine family” is to be read as a reference to “emission family”; (c) “nonroad engine” is to be read as a reference to “off-road engine”; and (d) “certified emissions life” is to be read as a reference to “useful life”. (4) The standards set out in the CFR that are referred to in these Regulations are the certification, in-use and field-testing standards and the test procedures, fuels and calculation methods referred to in CFR 60, CFR 89, CFR 94, CFR 1039, CFR 1042, CFR 1048, CFR 1051, CFR 1054, CFR 1060 or CFR 1068, as the case may be, for the model year in question. 2 For the purposes of these Regulations, an engine that is sold in Canada is considered to be sold concurrently in Canada and in the United States if an engine that belongs to the same emission family — or to the same emission families in the case of an engine that is subject to evaporative emission standards and belongs to more than one emission family — is offered for sale in the United States during the 365 days preceding (a) in the case of an engine that is imported into Canada, the day on which it is imported; and (b) in the case of an engine that is manufactured in Canada, (i) the day on which the national emissions mark is applied to the engine, if known, or (ii) if the day referred to in subparagraph (i) is not known, the day on which the manufacture of the engine was completed. 3 These Regulations apply in respect of the engines that are prescribed under section 5. 4 (1) A year that is used by a manufacturer of an engine as a model year must (a) if the period of production of a model of engine does not include January 1 of a calendar year, correspond to the calendar year during which the period of production falls; or (b) if the period of production of a model of engine includes January 1 of a calendar year, correspond to that calendar year. (2) The period of production must not include more than one January 1. (3) If an engine that is imported does not bear the engine’s date of manufacture, its model year corresponds to the calendar year during which it is imported. 5 (1) Mobile or stationary compression-ignition engines or mobile large spark-ignition engines — including those that have a complete fuel system — are prescribed for the purposes of the definition engine in section 149 of the Act unless they (a) are regulated under the On-Road Vehicle and Engine Emission Regulations; (b) are or will be installed in a vehicle that is regulated under the On-Road Vehicle and Engine Emission Regulations and are intended to propel such a vehicle; (c) are or will be installed in an auxiliary power unit, as defined in subsection 1(1) of the On-Road Vehicle and Engine Emission Regulations, that is or will be installed in a tractor that is regulated under those Regulations; (d) are regulated under the Marine Spark-ignition Engine, Vessel and Off-road Recreational Vehicle Emission Regulations; (e) are or will be installed in a vehicle that is regulated under the Marine Spark-ignition Engine, Vessel and Off-road Recreational Vehicle Emission Regulations and are intended to propel such a vehicle; (f) are designed exclusively for competition and (i) have performance characteristics that are substantially superior to non-competitive engines, (ii) are not displayed for sale in any public dealership or otherwise offered for sale to the general public, and (iii) bear a label that meets the requirements set out in section 34 and (A) sets out the statement “COMPETITION ENGINE / MOTEUR DE COMPÉTITION”, or (B) meets the requirements set out in section 620, subpart G, of CFR 1039 or, in accordance with section 630, subpart G, of CFR 1048, section 620, subpart G, of CFR 1054, as the case may be; (g) are designed to be used exclusively in a military machine that is designed for use in combat or combat support during military activities only, including reconnaissance missions, rescue missions and training missions, and bear (i) a label to that effect that meets the requirements set out in section 34 and sets out the statement “THIS ENGINE IS DESIGNED TO BE USED EXCLUSIVELY IN MILITARY MACHINES DESIGNED EXCLUSIVELY FOR USE IN COMBAT OR COMBAT SUPPORT DURING MILITARY ACTIVITIES / CE MOTEUR EST CONÇU POUR ÊTRE UTILISÉ EXCLUSIVEMENT DANS DES MACHINES MILITAIRES CONÇUES EXCLUSIVEMENT POUR ÊTRE UTILISÉES DANS LE CADRE D’OPÉRATIONS MILITAIRES DE COMBAT OU D’APPUI TACTIQUE”, or (ii) the United States emission control information label referred to in section 225(e), subpart C, of CFR 1068; (h) are to be exported, will not be used or sold for use in Canada and bear a label that meets the requirements set out in section 34 and sets out the statement “FOR EXPORT, NOT FOR USE OR SALE FOR USE IN CANADA / POUR EXPORTATION, NE DOIT PAS ÊTRE UTILISÉ AU CANADA NI VENDU POUR ÊTRE UTILISÉ AU CANADA”; (i) are regulated under the Multi-Sector Air Pollutants Regulations and bear a label that meets the requirements set out in section 34 and sets out the statement “THIS ENGINE IS REGULATED UNDER THE Multi-Sector Air Pollutants Regulations AND WILL BE USED IN A FACILITY LISTED IN SUBSECTION 46(4) OF THOSE REGULATIONS / CE MOTEUR EST RÉGLEMENTÉ PAR LE Règlement multisectoriel sur les polluants atmosphériques ET SERA UTILISÉ DANS UNE INSTALLATION ÉNUMÉRÉE AU PARAGRAPHE 46(4) DE CE RÈGLEMENT”; (j) have a displacement of 1 000 cm3 or less, a gross engine power of 30 kW or less and meet the requirements that are applicable under the Off-Road Small Spark-Ignition Engine Emission Regulations to an engine of the same model year that is designed to be used in a non-handheld machine; (k) are compression-ignition engines and (i) have a per-cylinder displacement of less than 50 cm3, (ii) are designed to be used in underground mines, but may also be used above ground at those mines, and are certified by (A) the Canada Centre for Mineral and Energy Technology, or (B) the Mine Safety and Health Administration of the United States in accordance with Title 30, chapter I, subchapter B, part 7, subpart E of the Code of Federal Regulations of the United States or Title 30, chapter I, subchapter B, part 36, of the Code of Federal Regulations of the United States, (iii) are designed to be installed in a vessel that has an integrated fuel, cooling or exhaust system, or (iv) are stationary, have a per-cylinder displacement of 30 L or more and bear (A) a label that meets the requirements set out in section 34 and sets out the statement “STATIONARY ENGINE WITH A DISPLACEMENT OF 30 L/CYLINDER OR MORE; NOT SUBJECT TO EMISSIONS STANDARDS UNDER THE CANADIAN REGULATIONS ENTITLED Off-road Compression-Ignition (Mobile and Stationary) and Large Spark-Ignition Engine Emission Regulations / MOTEUR FIXE AYANT UNE CYLINDRÉE DE 30 L OU PLUS; NON ASSUJETTI AUX NORMES D’ÉMISSIONS PRÉVUES PAR LE RÈGLEMENT CANADIEN INTITULÉ Règlement sur les émissions des moteurs hors route à allumage par compression (mobiles et fixes) et des gros moteurs hors route à allumage commandé”, or (B) the applicable United States emission control information label referred to in section 4210, subpart IIII, of CFR 60; or (l) are large spark-ignition engines, are or will be installed in or on an emergency machine and bear a label that meets the requirements set out in section 34 and sets out the statement “LARGE SPARK-IGNITION ENGINE FOR USE IN OR ON AN EMERGENCY MACHINE ONLY / GROS MOTEUR À ALLUMAGE COMMANDÉ POUR UTILISATION DANS OU SUR UNE MACHINE DE PREMIÈRE INTERVENTION SEULEMENT”. (2) For the purposes of section 152 of the Act, the prescribed engines are those referred to in subsection (1) that are manufactured in Canada other than (a) engines that (i) are covered by an EPA certificate, (ii) are sold concurrently in Canada and the United States, and (iii) had their manufacture completed in Canada by the addition of (A) an emission control system for exhaust emissions, or part of such a system, in a manner that conforms to the certificate and the certificate holder’s installation instructions, or (B) a complete fuel system, or part of such a system, in a manner that conforms to the certificate and the certificate holder’s installation instructions; and (b) engines that are to be used in Canada solely for purposes of exhibition, demonstration, evaluation or testing. (3) The classes of engines that are prescribed for the purposes of section 154 of the Act are those that are prescribed under subsection (1). 6 The evaporative emission standards referred to in these Regulations apply in respect of engines that have a complete fuel system with non-metallic fuel lines or fuel tanks and that are fuelled with volatile liquid fuels. 7 (1) An emission control system that is installed on an engine to enable it to conform to the standards set out in these Regulations must not (a) in its operation, release a substance that causes air pollution and that would not have been released if the system had not been installed; or (b) in its operation or malfunction, make the engine or the machine in which the engine is installed unsafe, or endanger persons or property near the engine or machine. (2) An engine must not be equipped with an auxiliary emission control device that reduces the effectiveness of the emission control system under conditions that may reasonably be expected to be encountered under normal operation of the engine, unless a description of the auxiliary emission control device is included in the evidence of conformity under section 40 or 41 and (a) the conditions under which the auxiliary emission control device operates are substantially included in the test procedures referred to in subsection 1(4); (b) the auxiliary emission control device is needed to protect the engine against damage or accident; (c) the auxiliary emission control device is only used to start the engine; (d) the auxiliary emission control device is installed in a compression-ignition engine that is designed to power an emergency machine and is activated during emergency response operations to maintain speed, torque or power in either of the following circumstances: (i) the emission control system is in an abnormal state, or (ii) the device acts to maintain the emission control system in a normal state; or (e) the auxiliary emission control device is installed in a compression-ignition engine other than one referred to in paragraph (d) and the following criteria are met: (i) the auxiliary emission control device (A) is designed to prevent the operation of the emission control system only to the extent necessary to allow the engine to meet the demands of an emergency situation, (B) is accompanied by a notice in writing discouraging improper use of the auxiliary emission control device, (C) is designed so that it can only operate for a maximum of 120 hours in total before it has to be reset, (D) is designed so that it can only be reset to reestablish the time limit referred to in clause (C) by the input of a temporary code, the reconfiguration of the engine’s electronic control module or the use of another secure feature that is unique to each engine, and (E) is designed so that its operation can be manually stopped, and (ii) the engine on which the auxiliary emission control device is installed is designed to electronically record the number of times the auxiliary emission control device is used. (3) Subject to subsection 11(2), if a compression-ignition engine is equipped with an auxiliary emission control device referred to in subsection (2) that meets the requirements set out in paragraph (2)(d) or (e), the engine and the diagnostic system with which it is equipped are not required to conform to the following standards when the auxiliary emission control device is operating: (a) in the case of the engine, the standards referred to in sections 10 to 16; and (b) in the case of the diagnostic system, the standards referred to in section 17. 8 (1) Engines equipped with adjustable parameters must conform to the applicable standards under these Regulations for any specification within the physically adjustable range. (2) Subsection (1) does not apply to an engine that is designed to operate using fuel that is not generally offered for sale in Canada if the engine is adjusted in accordance with the manufacturer’s instructions referred to in subsection 36(2) and conforms to the applicable standards under these Regulations for those specifications. 9 (1) Despite subsection 1(4), a company may, instead of using the test procedures set out in CFR 60 in respect of their stationary compression-ignition engines, replace one or more of those test procedures with alternative test procedures that have parameters and specifications that are equivalent to or more stringent than the parameters and specifications of the test procedures set out in CFR 60. (2) The alternative test procedures referred to in subsection (1) must be included in a test procedure published by (a) the government of a state or of a political subdivision of a state, or an institution of a state or of a political subdivision of a state; (b) an international organization of states or an international organization that is established by the governments of states, or an institution of any of those international organizations; or (c) an organization that develops test procedures based on consensus and that is internationally recognized as being competent to establish those test procedures. (3) A company that uses alternative test procedures under subsection (1) must, as part of the evidence of conformity under section 40 or 41, as the case may be, include evidence demonstrating that the alternative test procedures have parameters and specifications that are equivalent to or more stringent than the parameters and specifications of the test procedures set out in CFR 60. 10 (1) Subject to sections 12 to 15 and 22 and 23, a mobile compression-ignition engine must conform to (a) the exhaust emission standards set out in sections 101(a) to (c) and (e) and (f), subpart B, of CFR 1039; (b) the crankcase emission standards set out in section 115(a), subpart B, of CFR 1039; (c) the smoke emission standards set out in section 105, subpart B, of CFR 1039; and (d) the evaporative emission standards set out in sections 105(a), (c) and (d), subpart B, of CFR 1048 for large spark-ignition engines. (2) The standards referred to in subsection (1) apply for the useful life of the engine, as specified (a) in the case of the standards referred to in paragraphs (1)(a) to (c), in section 101(g), subpart B, of CFR 1039; and (b) in the case of the standards referred to in paragraph (1)(d), in section 105, subpart B, of CFR 1048. 11 (1) Subject to sections 15, 16 and 23, a stationary compression-ignition engine must conform to the emission standards set out in sections 4201(a), (c) and (e)(2), subpart IIII, of CFR 60. (2) An engine referred to in subsection (1) that is equipped with an auxiliary emission control device referred to in subsection 7(2) that meets the requirements set out in paragraph 7(2)(d) or (e) must conform to the emission standards set out in section 4210(j), subpart IIII, of CFR 60 when the auxiliary emission control device is operating. (3) The standards referred to in subsection (1) apply for the applicable useful life, as follows: (a) for engines that have a per-cylinder displacement of less than 10 L, (i) for engines that have a gross power of less than 19 kW, a period of 3000 hours of operation or five years of use, whichever occurs first, or the useful life referred to in section 101(g), subpart B, of CFR 1039, (ii) for constant speed engines that have a gross power of 19 kW or more but less than 37 kW and a rated speed of 3000 rpm or more, a period of 3000 hours of operation or five years of use, whichever occurs first, or the useful life referred to in section 101(g), subpart B, of CFR 1039, (iii) for engines, other than those referred to in subparagraph (ii), that have a gross power of 19 kW or more but less than 37 kW, a period of 5000 hours of operation or seven years of use, whichever occurs first, or the useful life referred to in section 101(g), subpart B, of CFR 1039, and (iv) for engines that have a gross power of 37 kW or more, a period of 8000 hours of operation or 10 years of use, whichever occurs first, or the useful life referred to in section 101(g), subpart B, of CFR 1039; and (b) for engines that have a per-cylinder displacement of 10 L or more but less than 30 L, a period of 20,000 hours of operation or 10 years of use, whichever occurs first, or the useful life referred to in section 101(e), subpart B, of CFR 1042. 12 (1) A mobile compression-ignition engine that is to be used exclusively to provide a primary source of electrical power in a remote location may, instead of conforming to the emission standards set out in section 10, conform to the emission standards set out in (a) for engines that have a gross power of less than 37 kW, Table 2, subpart IIII, of CFR 60; and (b) for engines that have a gross power of 37 kW or more, Table 1 to section 112(a), subpart B, of CFR 89. (2) The standards referred to in subsection (1) apply for the applicable useful life, as follows: (a) for engines that have a gross power of less than 19 kW, a period of 3000 hours of operation or five years of use, whichever occurs first; (b) for constant speed engines that have a gross power of 19 kW or more but less than 37 kW and a rated speed of 3000 rpm or more, a period of 3000 hours of operation or five years of use, whichever occurs first; (c) for engines, other than those referred to in paragraph (b), that have a gross power of 19 kW or more but less than 37 kW, a period of 5000 hours of operation or seven years of use, whichever occurs first; and (d) for engines that have a gross power of 37 kW or more, a period of 8000 hours of operation or 10 years of use, whichever occurs first. 13 (1) A mobile compression-ignition engine that is to be used exclusively at a North Warning System site established by the North American Aerospace Defense Command may, instead of conforming to the emission standards set out in section 10, conform to the emission standards set out in Table 1 to section 112(a), subpart B, of CFR 89. (2) The standards referred to in subsection (1) apply for the applicable useful life, as follows: (a) for engines that have a gross power of less than 19 kW, a period of 3000 hours of operation or five years of use, whichever occurs first; (b) for constant speed engines that have a gross power of 19 kW or more but less than 37 kW and a rated speed of 3000 rpm or more, a period of 3000 hours of operation or five years of use, whichever occurs first; (c) for engines, other than those referred to in paragraph (b), that have a gross power of 19 kW or more but less than 37 kW, a period of 5000 hours of operation or seven years of use, whichever occurs first; and (d) for engines that have a gross power of 37 kW or more, a period of 8000 hours of operation or 10 years of use, whichever occurs first. 14 (1) A mobile compression-ignition engine that is used in a transportation refrigeration unit may, instead of conforming to the emission standards referred to in section 10, conform to the applicable standards referred to in sections 645(a), (b) and (e), subpart G, of CFR 1039, as specified in those sections. (2) The standards referred to in subsection (1) apply for the useful life of the engine as specified in section 101(g), subpart B, of CFR 1039. 15 (1) A compression-ignition engine that is or will be installed in a machine to be used only in a hazardous location where the maximum permissible surface temperature for the machine is 200°C or less may, if the engine or the machine bears the markings referred to in rule 18-052 of the most recent version of the Canadian Standards Association standard C22.1, Canadian Electrical Code, Part 1, conform to the following emission standards instead of those referred to in subsection 10(1) or 11(1), as applicable: (a) in the case of an engine that has a gross power of 19 kW or more but less than 37 kW, the applicable standards set out in Table 2 to section 102(b), subpart B, of CFR 1039; and (b) in the case of an engine that has a gross power of 37 kW or more, the applicable standards set out in Table 1 to section 112(a), subpart B, of CFR 89. (2) The standards referred to in subsection (1) apply for the following useful life: (a) for engines that have a gross power of 19 kW or more but less than 37 kW, the useful life referred to in section 101(g), subpart B, of CFR 1039; and (b) for engines that have a gross power of 37 kW or more, a period of 8000 hours of operation or 10 years of use, whichever occurs first. 16 (1) A stationary compression-ignition engine that is intended to provide electrical power or mechanical work during a power outage may, instead of conforming to the emission standards referred to in subsection 11(1), conform to those set out in sections 4202(a)(1)(ii), (a)(2), (b)(2), (e)(2) and (4) and (f)(1) and (2), subpart IIII, of CFR 60. (2) A stationary compression-ignition engine that is a fire-pump engine may, instead of conforming to the emission standards referred to in subsection 11(1), conform to those set out in section 4202(d), subpart IIII, of CFR 60. (3) A stationary compression-ignition engine that is to be used in a remote location may, instead of conforming to the emission standards set out in subsection 11(1), conform to those set out in section 4201(f), subpart IIII, of CFR 60 or those set out in sections 4202(a)(1)(ii), (a)(2), (b)(2), (e)(2) and (4) and (f)(1) and (2), subpart IIII, of CFR 60. (4) The standards referred to in subsections (1) to (3) apply for the useful life of the engine referred to in subsection 11(3). 17 A compression-ignition engine that is equipped with a selective catalytic reduction system that uses a reductant other than the engine’s fuel must be equipped with a diagnostic system that conforms to the standards set out in, (a) in the case of mobile engines, section 110, subpart B, of CFR 1039; and (b) in the case of stationary engines, section 110, subpart B, of CFR 1039 or section 110, subpart B, of CFR 1042, as applicable. 18 (1) Subject to subsections (3) and (4) and sections 19, 22 and 23, a large spark-ignition engine must conform to (a) the exhaust emission standards set out in sections 101(a) to (c) and (e), subpart B, of CFR 1048; (b) the crankcase emission standards set out in section 115(a), subpart B, of CFR 1048; and (c) the evaporative emission standards set out in sections 105(a), (c) and (d), subpart B, of CFR 1048. (2) For greater certainty, a company may demonstrate an engine’s conformity to the evaporative emission standards referred to in paragraph (1)(c) as specified in section 245(e), subpart C, of CFR 1048. (3) An engine that meets the conditions set out in sections 101(d)(1) to (4), subpart B, of CFR 1048 may, instead of conforming to the exhaust emission standards set out in section 101(b)(3), subpart B, of CFR 1048, conform to the exhaust emission standards set out in section 101(d), subpart B, of CFR 1048. (4) An engine may, instead of conforming to the exhaust emission standards referred to in paragraph (1)(a), conform to the “Blue Sky Series” standards set out in section 140, subpart B, of CFR 1048. (5) The standards referred to in subsections (1), (3) and (4) apply for the useful life of the engine as specified in (a) section 101(g), subpart B, of CFR 1048, in the case of the standards referred to in paragraphs (1)(a) and (b) and subsections (3) and (4); or (b) section 105, subpart B, of CFR 1048, in the case of the standards referred to in paragraph (1)(c). 19 A large spark-ignition engine that is fuelled solely by natural gas or liquefied petroleum gas and that has a gross engine power of 250 kW or more may, instead of conforming to the standards referred to in sections 18, 20 and 21, conform to the standards referred to in sections 10 and 17, as if it were a compression-ignition engine. 20 A large spark-ignition engine that is equipped with three-way catalysts and closed-loop control of air-fuel ratios must be equipped with a diagnostic system that conforms to the applicable standards set out in section 110, subpart B, of CFR 1048. 21 An electronically controlled large spark-ignition engine must be equipped with a torque broadcasting system that meets the requirements of section 115(b), subpart B, of CFR 1048. 22 (1) A mobile compression-ignition engine or a large spark-ignition engine may, instead of conforming to the applicable standards referred to in sections 10, 12 to 15 and 17 to 21, conform to the applicable standards under the On-Road Vehicle and Engine Emission Regulations if (a) the engine was, before it became subject to these Regulations, (i) subject to the On-Road Vehicle and Engine Emission Regulations, and (ii) in conformity with the applicable standards under those Regulations; and (b) the engine was, before its sale to the first retail purchaser, altered in a manner that meets the requirements set out in section 605(d)(2), subpart G, of CFR 1039 or section 605(d)(2), subpart G, of CFR 1048, as the case may be. (2) For the purposes of subsection (1), the applicable standards under the On-Road Vehicle and Engine Emission Regulations are those that were applicable to the engine under those Regulations before its alteration. 23 (1) Subject to subsection (2), an engine that is covered by an EPA certificate may, instead of conforming to the applicable standards referred to in sections 10 to 22, conform to (a) in the case of an engine that has a complete fuel system and whose attached fuel lines and attached fuel tanks are covered by one or more EPA certificates, the standards referred to in each of the EPA certificates; and (b) in any other case, the standards referred to in the EPA certificate. (2) A mobile compression-ignition engine or a large spark-ignition engine that is covered by an EPA certificate issued under CFR 86 may, instead of conforming to the applicable standards referred to in sections 10, 12 to 15 and 17 to 21, conform to the standards referred to in the EPA certificate if the engine was, before importation or before its sale to the first retail purchaser, altered in a manner that meets the specific requirements set out in section 605(d)(2), subpart G, of CFR 1039 or section 605(d)(2), subpart G, of CFR 1048, as the case may be. 24 (1) For the purposes of subsection 153(3) of the Act, the provisions of the CFR that are applicable under an EPA certificate to an engine referred to in subsection 23(1) or (2), or to any attached fuel lines or fuel tanks referred to in paragraph 23(1)(a), correspond to the standards referred to in sections 10 to 22. (2) For the purposes of subsection 153(3) of the Act, the EPA is the prescribed agency. 25 (1) Despite sections 10 to 23 and subject to subsection (2), a replacement engine must, instead of conforming to the applicable standards referred to in those sections, conform to (a) if a replacement engine exists that is manufactured to the specifications, in respect of the control of emissions, of a model year subsequent to the model year of the original engine and that has the physical or performance characteristics necessary for the operation of the machine, the most stringent of the following: (i) the standards referred to in paragraph 10(1)(a) or (b) or subsection 11.1(2) of the Off-Road Compression-Ignition Engine Emission Regulations, as they read immediately before the coming into force of these Regulations, that are applicable to an engine manufactured to the specifications of that subsequent model year, (ii) if a replacement engine exists that conforms to standards that are applicable to a model year that is subsequent to the model year referred to in subparagraph (i), those standards, or (iii) if none of the standards referred to in subparagraph (i) or (ii) are applicable, the manufacturer’s specifications in respect of the control of emissions, if those specifications are at least as stringent as the specifications of the model year of the original engine; and (b) if no replacement engine exists that is manufactured to the specifications, in respect of the control of emissions, of a model year subsequent to the model year of the original engine and that has the physical or performance characteristics necessary for the operation of the machine, the most stringent of the following: (i) the standards referred to in paragraph 10(1)(a) or (b) or subsection 11.1(2) or 13(2) of the Off-Road Compression-Ignition Engine Emission Regulations, as they read immediately before the coming into force of these Regulations, that are applicable to the original engine, (ii) if a replacement engine exists that has the physical or performance characteristics necessary for the operation of the machine and conforms to standards that are applicable to the model year of the original engine and are more stringent than those referred to in subparagraph (i), those more stringent standards, or (iii) if none of the standards referred to in subparagraph (i) or (ii) are applicable, the manufacturer’s specifications in respect of the control of emissions, if those specifications are at least as stringent as the specifications of the model year of the original engine. (2) For the purposes of subparagraphs (1)(a)(i) and (1)(b)(i), a reference in the Off-Road Compression-Ignition Engine Emission Regulations to a provision of the CFR is to be read as a reference to that provision as it read immediately before the day on which these Regulations come into force. (3) For the purposes of subparagraph (1)(b)(i), the reference to subsection 13(2) of the Off-Road Compression-Ignition Engine Emission Regulations must be read as excluding the dates mentioned in that subsection. (4) An engine is a replacement engine only if it was manufactured to replace the engine of a machine that is located in Canada and that, on the day that the replacement engine is installed, had its manufacture completed (a) in the case of a machine in or on which a mobile engine is installed, 40 years ago or less; or (b) in the case of a machine in or on which a stationary engine is installed, less than 15 years ago. 26 (1) Before applying a national emissions mark to an engine, a company must make a request to the Minister for authorization to do so. (2) The request must be signed by an authorized representative of the company and must include (a) the company’s name and the street address of the company’s head office and, if different, its mailing address; (b) the name, email address and telephone number of an authorized representative of the company; (c) the street address of the location at which the national emissions mark will be applied; and (d) information establishing that the company is capable of demonstrating that the engine conforms to the standards set out in these Regulations. 27 (1) The national emissions mark is the mark set out in the schedule. (2) The national emissions mark must be at least 7 mm in height and 10 mm in width. (3) A company that is authorized to apply the national emissions mark must display the authorization number assigned by the Minister in figures that are at least 2 mm in height, immediately below or to the right of the national emissions mark. 28 (1) A compression-ignition engine or a large spark-ignition engine that meets the alternative standards referred to in section 19 — other than an engine that is covered by an EPA certificate, an engine that is used in a transportation refrigeration unit and that conforms to the alternative standards referred to in subsection 14(1) or a replacement engine — must bear a label that sets out (a) except in the case of a model of engine referred to in section 33, the statement “THIS ENGINE CONFORMS TO ALL APPLICABLE STANDARDS PRESCRIBED BY THE CANADIAN REGULATIONS ENTITLED Off-road Compression-Ignition (Mobile and Stationary) and Large Spark-Ignition Engine Emission Regulations IN EFFECT FOR MODEL YEAR [insert model year] / CE MOTEUR EST CONFORME AUX NORMES APPLICABLES PRÉVUES PAR LE RÈGLEMENT CANADIEN INTITULÉ Règlement sur les émissions des moteurs hors route à allumage par compression (mobiles et fixes) et des gros moteurs hors route à allumage commandé EN VIGUEUR POUR L’ANNÉE DE MODÈLE [inscrire l’année de modèle]”; (b) the following statements, as applicable: (i) in the case of an engine that is to operate at a constant-speed only, “FOR USE AT CONSTANT-SPEED ONLY / POUR UTILISATION À VITESSE CONSTANTE SEULEMENT”, (ii) in the case of an engine that has a gross power of more than 560 kW and meets the exhaust emission standards set out in Table 1 to section 101(b), subpart B, of CFR 1039, except those that are applicable to engines to be used in a generator set, “NOT FOR USE IN A GENERATOR SET / NE PAS UTILISER DANS UNE GÉNÉRATRICE”, (iii) in the case of an engine referred to in paragraph 7(2)(d), “FOR USE IN EMERGENCY MACHINE ONLY / POUR UTILISATION DANS UNE MACHINE DE PREMIÈRE INTERVENTION SEULEMENT”, (iv) in the case of an engine referred to in subsection 8(2), “THIS ENGINE IS DESIGNED TO OPERATE USING FUEL THAT IS NOT GENERALLY OFFERED FOR SALE IN CANADA; ENGINE PARAMETERS MUST BE ADJUSTED ACCORDING TO THE MANUFACTURER’S INSTRUCTIONS / CE MOTEUR EST CONÇU POUR ÊTRE ALIMENTÉ AVEC UN CARBURANT QUI N’EST GÉNÉRALEMENT PAS MIS EN VENTE AU CANADA; LES PARAMÈTRES DU MOTEUR DOIVENT ÊTRE RÉGLÉS CONFORMÉMENT AUX INSTRUCTIONS DU FABRICANT”, (v) in the case of an engine that has been tested using alternative test procedures referred to in section 9, “STATIONARY ENGINE TESTED USING THE FOLLOWING ALTERNATIVE TEST PROCEDURES: [insert name of test procedures] / MOTEUR FIXE MIS À L’ESSAI SELON LES MÉTHODES D’ESSAI DE RECHANGE SUIVANTES : [inscrire le nom des méthodes d’essai]”, (vi) in the case of an engine that conforms to the emission standards referred to in section 11, “STATIONARY ENGINE / MOTEUR FIXE”, (vii) in the case of an engine that conforms to the alternative emission standards referred to in section 12, “MOBILE ENGINE FOR USE IN REMOTE LOCATIONS ONLY / MOTEUR MOBILE POUR UTILISATION EN RÉGIONS ÉLOIGNÉES SEULEMENT”, (viii) in the case of an engine that conforms to the alternative emission standards referred to in section 13, “MOBILE ENGINE FOR USE AT NORTH WARNING SYSTEM SITES ONLY / MOTEUR MOBILE POUR UTILISATION AUX SITES DU SYSTÈME D’ALERTE DU NORD SEULEMENT”, (ix) in the case of an engine that conforms to the alternative emission standards referred to in subsection 15(1), “ENGINE FOR USE IN CLASS I HAZARDOUS LOCATIONS ONLY / MOTEUR POUR UTILISATION DANS DES EMPLACEMENTS DANGEREUX DE CLASSE I SEULEMENT”, (x) in the case of an engine that conforms to the alternative emission standards referred to in subsection 16(1), “STATIONARY ENGINE FOR USE AS BACKUP OR EMERGENCY ENGINE / MOTEUR FIXE POUR UTILISATION COMME MOTEUR DE RÉSERVE OU D’URGENCE”, (xi) in the case of an engine that conforms to the alternative emission standards referred to in subsection 16(2), “STATIONARY ENGINE FOR USE AS A FIRE PUMP ENGINE ONLY / MOTEUR FIXE POUR UTILISATION COMME MOTEUR DE POMPE À INCENDIE SEULEMENT”, (xii) in the case of an engine that conforms to the alternative emission standards referred to in subsection 16(3), “STATIONARY ENGINE FOR USE IN REMOTE LOCATIONS / MOTEUR FIXE POUR UTILISATION EN RÉGIONS ÉLOIGNÉES”, and (xiii) in the case of an engine that conforms to the alternative emission standards referred to in subsection 22(1), “ADAPTED FOR OFF-ROAD USE WITHOUT AFFECTING EMISSION CONTROLS / MODIFIÉ POUR USAGE HORS ROUTE SANS NUIRE AU CONTRÔLE DES ÉMISSIONS”; (c) the model year of the engine; (d) the month and the four-digit year of manufacture of the engine, expressed as numbers separated by a non-numeric character or space, unless this information is permanently identified elsewhere on the engine; (e) the gross power or gross power category of the engine; (f) if the engine is installed in an off-road recreational vehicle, the numerical value of the exhaust emission standards to which it conforms and the applicable units of measure; (g) an identification of the emission control system, as specified in section 45(f), subpart A, of CFR 1068; (h) the name and trademark of the engine manufacturer or, if the manufacturer is authorized by another business entity to use that business entity’s name and trademark, that name and trademark; (i) the engine’s emission family; and (j) the engine displacement. (2) Subject to subsection 34(4), a compression-ignition engine that has a complete fuel system with a non-metallic fuel line or fuel tank and is fuelled with volatile liquid fuel — other than an engine that is covered by an EPA certificate, an engine that is used in a transportation refrigeration unit and that conforms to the alternative standards referred to in subsection 14(1) or a replacement engine — must bear a label that includes the following information, in addition to the information set out in subsection (1): (a) except in the case of a model of engine referred to in section 33, the statement “THIS ENGINE AND THE COMPLETE FUEL SYSTEM CONFORM TO ALL APPLICABLE STANDARDS PRESCRIBED BY THE CANADIAN REGULATIONS ENTITLED Off-road Compression-Ignition (Mobile and Stationary) and Large Spark-Ignition Engine Emission Regulations IN EFFECT FOR MODEL YEAR [insert model year] / CE MOTEUR ET LE SYSTÈME COMPLET D’ALIMENTATION EN CARBURANT SONT CONFORMES AUX NORMES APPLICABLES PRÉVUES PAR LE RÈGLEMENT CANADIEN INTITULÉ Règlement sur les émissions des moteurs hors route à allumage par compression (mobiles et fixes) et des gros moteurs hors route à allumage commandé EN VIGUEUR POUR L’ANNÉE DE MODÈLE [inscrire l’année de modèle]”; (b) the name of the company that installed the complete fuel system; and (c) the emission family in respect of evaporative emissions. (3) Paragraphs (1)(a) and (2)(a) and (b) do not apply if a national emissions mark is affixed to the engine or to the machine in which the engine is installed. (4) Paragraph (1)(g) does not apply if there is insufficient space on the label to accommodate the information referred to in that paragraph and that information is included in the emissions-related maintenance instructions. 29 (1) A large spark-ignition engine — other than an engine that meets the alternative standards referred to in section 19, an engine that is covered by an EPA certificate or a replacement engine — must bear a label that sets out (a) except in the case of a model of engine referred to in section 33, the statement “THIS ENGINE CONFORMS TO ALL APPLICABLE STANDARDS PRESCRIBED BY THE CANADIAN REGULATIONS ENTITLED Off-road Compression-Ignition (Mobile and Stationary) and Large Spark-Ignition Engine Emission Regulations IN EFFECT FOR MODEL YEAR [insert model year] / CE MOTEUR EST CONFORME AUX NORMES APPLICABLES PRÉVUES PAR LE RÈGLEMENT CANADIEN INTITULÉ Règlement sur les émissions des moteurs hors route à allumage par compression (mobiles et fixes) et des gros moteurs hors route à allumage commandé EN VIGUEUR POUR L’ANNÉE DE MODÈLE [inscrire l’année de modèle]”; (b) the following statements, as applicable: (i) in the case of an engine that is intended for use in constant-speed applications only, “USE IN CONSTANT-SPEED APPLICATIONS ONLY / UTILISEZ SEULEMENT DANS DES APPLICATIONS À VITESSE CONSTANTE”, (ii) in the case of an engine that is intended for use in variable-speed applications only, “USE IN VARIABLE-SPEED APPLICATIONS ONLY / UTILISEZ SEULEMENT DANS DES APPLICATIONS À VITESSE VARIABLE”, (iii) in the case of an engine that is intended for use in high-load applications only, “THIS ENGINE IS NOT INTENDED FOR OPERATION AT LESS THAN 75% OF FULL LOAD / CE MOTEUR N’EST PAS DESTINÉ À FONCTIONNER À MOINS DE 75 % DE SA CAPACITÉ MAXIMALE”, (iv) in the case of an engine referred to in subsection 8(2), “THIS ENGINE IS DESIGNED TO OPERATE USING FUEL THAT IS NOT GENERALLY OFFERED FOR SALE IN CANADA; ENGINE PARAMETERS MUST BE ADJUSTED ACCORDING TO THE MANUFACTURER’S INSTRUCTIONS / CE MOTEUR EST CONÇU POUR ÊTRE ALIMENTÉ AVEC UN CARBURANT QUI N’EST GÉNÉRALEMENT PAS MIS EN VENTE AU CANADA; LES PARAMÈTRES DU MOTEUR DOIVENT ÊTRE RÉGLÉS CONFORMÉMENT AUX INSTRUCTIONS DU FABRICANT”, (v) in the case of an engine referred to in subsection 18(3) that conforms to the alternate exhaust emission standards referred to in that subsection and that is not intended for use in high-load applications, “THIS ENGINE IS NOT INTENDED FOR OPERATION AT MORE THAN [insert percentage of full load based on the nature of the engine protection] OF FULL LOAD / CE MOTEUR N’EST PAS DESTINÉ À FONCTIONNER À PLUS DE [inscrire le pourcentage de sa capacité maximale selon la nature de la protection du moteur] DE SA CAPACITÉ MAXIMALE”, (vi) in the case of an engine that conforms to the “Blue Sky Series” standards referred to in subsection 18(4), “BLUE SKY SERIES”, and (vii) in the case of an engine that conforms to the alternative emission standards referred to in subsection 22(1), “ADAPTED FOR OFF-ROAD USE WITHOUT AFFECTING EMISSION CONTROLS / MODIFIÉ POUR USAGE HORS ROUTE SANS EFFET SUR LE CONTRÔLE DES ÉMISSIONS”; (c) the model year of the engine; (d) the month and the four-digit year of manufacture of the engine, expressed as numbers separated by a non-numeric character or space, unless this information is permanently identified elsewhere on the engine; (e) the numerical value of the exhaust emission standards to which it complies and the applicable units of measure; (f) an identification of the emission control system, using terms and abbreviations as specified in section 45(f), subpart A, of CFR 1068; (g) an identification of any requirements for fuel and lubricants; (h) the engine accessories that must be operating and the proper transmission gear during engine maintenance; (i) the name and trademark of the engine manufacturer or, if the manufacturer is authorized by another business entity to use that business entity’s name and trademark, that name and trademark; (j) the engine’s emission family; and (k) the engine displacement. (2) Subject to subsection 34(4), a large spark-ignition engine that has a complete fuel system — other than an engine that is covered by an EPA certificate or a replacement engine — must bear a label that includes the following information, in addition to the information set out in subsection (1): (a) except in the case of a model of engine referred to in section 33, the statement “THIS ENGINE AND THE COMPLETE FUEL SYSTEM CONFORM TO ALL APPLICABLE STANDARDS PRESCRIBED BY THE CANADIAN REGULATIONS ENTITLED Off-road Compression-Ignition (Mobile and Stationary) and Large Spark-Ignition Engine Emission Regulations IN EFFECT FOR MODEL YEAR [insert model year] / CE MOTEUR ET LE SYSTÈME COMPLET D’ALIMENTATION EN CARBURANT SONT CONFORMES AUX NORMES APPLICABLES PRÉVUES PAR LE RÈGLEMENT CANADIEN INTITULÉ Règlement sur les émissions des moteurs hors route à allumage par compression (mobiles et fixes) et des gros moteurs hors route à allumage commandé EN VIGUEUR POUR L’ANNÉE DE MODÈLE [inscrire l’année de modèle]”; (b) the name of the company that installed the complete fuel system; and (c) the emission family in respect of evaporative emissions. (3) Paragraphs (1)(a) and (2)(a) and (b) do not apply if a national emissions mark is affixed to the engine or to the machine in which the engine is installed. (4) Paragraph (1)(f), (g) or (h) does not apply if there is insufficient space on the label to accommodate the information referred to in one of those paragraphs and that information is included in the emissions-related maintenance instructions. 30 An engine that conforms to the alternative standards referred to in subsection 14(1) must bear either a label (a) that sets out (i) the statement “ENGINE TO BE USED IN A TRANSPORTATION REFRIGERATION UNIT ONLY / MOTEUR À UTILISER SEULEMENT DANS UN DISPOSITIF FRIGORIFIQUE DE TRANSPORT”, (ii) the model year of the engine, (iii) the month and the four-digit year of manufacture of the engine, expressed as numbers separated by a non-numeric character or space, unless this information is permanently identified elsewhere on the engine, (iv) the gross power or gross power category of the engine, (v) an identification of the emission control system, and (vi) the name of the engine manufacturer; or (b) that meets the requirement set out in section 645(d)(1), subpart G, of CFR 1039. 31 A replacement engine must bear a label that (a) sets out the following information: (i) in the case of a mobile engine, the statement “FOR USE AS A REPLACEMENT ENGINE ONLY — NOT FOR INSTALLATION IN A MACHINE THAT IS MORE THAN 40 YEARS OLD / POUR UTILISATION COMME MOTEUR DE REMPLACEMENT SEULEMENT — NE PEUT ÊTRE INSTALLÉ DANS UNE MACHINE DE PLUS DE 40 ANS”, (ii) in the case of a stationary engine, the statement “FOR USE AS A REPLACEMENT ENGINE ONLY — NOT FOR INSTALLATION IN A MACHINE THAT IS MORE THAN 15 YEARS OLD / POUR UTILISATION COMME MOTEUR DE REMPLACEMENT SEULEMENT — NE PEUT ÊTRE INSTALLÉ DANS UNE MACHINE DE PLUS DE 15 ANS”, (iii) if the engine conforms to the standards referred to in subparagraph 25(1)(a)(i) or (ii) or (b)(i) or (ii), the statement “TO REPLACE AN ENGINE THAT IS SUBJECT TO EMISSION STANDARDS FOR [insert the model year(s) or “tier(s)”, within the meaning of the CFR, of the engines that may be replaced] ENGINES ONLY / POUR REMPLACEMENT D’UN MOTEUR QUI EST ASSUJETTI AUX NORMES D’ÉMISSIONS POUR LES MOTEURS DE [inscrire l’année ou les années de modèle ou le « tier » ou les « tiers », au sens du CFR, des moteurs qui peuvent être remplacés] SEULEMENT”, (iv) the model year of the engine, (v) the month and the four-digit year of manufacture of the engine, expressed as numbers separated by a non-numeric character or space, unless this information is permanently identified elsewhere on the engine, (vi) the numerical value of the exhaust emission standards to which it conforms, if any, and the applicable units of measure, (vii) in the case of a compression-ignition engine, the gross power or gross power category of the engine, (viii) an identification of the emission control system, and (ix) the name of the engine manufacturer; or (b) meets the requirements set out in section 240(b)(5), subpart C, of CFR 1068. 32 An engine that is covered by an EPA certificate and that, as authorized by subsection 23(1) or (2), conforms to the standards referred to in the EPA certificate instead of the applicable standards referred to in sections 10 to 21, must bear a United States emission control information label that meets the requirements set out in the following provisions: (a) if the engine is a mobile compression-ignition engine, (i) in the case of an engine that is covered by an EPA certificate issued under CFR 1039, sections 135(b) to (g), subpart B, of CFR 1039, and, (A) if the engine is equipped with adjustable parameters and is designed to operate using fuel that is not generally offered for sale in Canada, section 615(b)(2), subpart G, of CFR 1039, and (B) if the engine is used in a transportation refrigeration unit, section 645(d)(1), subpart G, of CFR 1039, or (ii) in the case of an engine that is covered by an EPA certificate issued under CFR 86, section 35, subpart A, of CFR 86 and section 605(d)(5), subpart G, of CFR 1039; (b) if the engine is a stationary compression-ignition engine that is covered by an EPA certificate issued under CFR 60, CFR 1039 or CFR 1042, as applicable, (i) sections 4210(c), (f) and (g), subpart IIII, of CFR 60, (ii) sections 135(b) to (g), subpart B, of CFR 1039 and, if the engine is equipped with adjustable parameters and is designed to operate using fuel that is not generally offered for sale in Canada, section 615(b)(2), subpart G, of CFR 1039, or (iii) sections 135(b) to (g), subpart B, of CFR 1042; (c) if the engine is a large spark-ignition engine, (i) in the case of an engine that is covered by an EPA certificate issued under CFR 1048, sections 135(b) to (f), subpart B, of CFR 1048 and, if the engine is equipped with adjustable parameters and is designed to operate using fuel that is not generally offered for sale in Canada, section 625(b)(2), subpart G, of CFR 1048, (ii) in the case of an engine that is covered by an EPA certificate issued under CFR 86, section 35, subpart A, of CFR 86 and section 605(d)(5), subpart G, of CFR 1048, or (iii) in the case of an engine that is covered by an EPA certificate issued under CFR 1039, sections 135(b) to (g), subpart B, of CFR 1039, and, (A) if the engine is equipped with adjustable parameters and is designed to operate using fuel that is not generally offered for sale in Canada, section 615(b)(2), subpart G, of CFR 1039, and (B) if the engine is used in a transportation refrigeration unit, section 645(d)(1), subpart G, of CFR 1039; and (d) if the engine is equipped with a complete fuel system whose attached fuel lines and attached fuel tanks are covered by one or more EPA certificates issued under CFR 1060, sections 135(a) to (e), subpart B, of CFR 1060. 33 In the case of a model of engine in respect of which the Governor in Council has, by order, granted an exemption under section 156 of the Act, the engine must bear a label that sets out, in both official languages, the standard in respect of which the exemption has been granted, as well as the Privy Council number and date of the order. 34 (1) Subject to subsection (3), the national emissions mark and any label required by these Regulations, other than a label referred to in section 3

    The text continues in the official source.

    Related guides, FAQ and contract templates