LEGALDIGMLEGALDIGM
    ← Canada
    Beta
    SOR-2016-151:en

    SOR-2016-151:en — Multi-Sector Air Pollutants Regulations

    Beta. Legal information, not legal advice. LEGALDIGM is not a law firm. Check the official source for the current text.

    Analyze this law with AI
    1 (1) For the purpose of protecting the environment and human health, Parts 1, 2 and 3 of these Regulations establish, respectively, requirements for the emission of the following air pollutants: (a) NOx from boilers and heaters in certain regulated facilities in various industrial sectors; (b) NOx from stationary spark-ignition engines that combust gaseous fuels in certain regulated facilities in various industrial sectors; and (c) NOx and SO2 from cement manufacturing facilities. (2) Part 4 sets out general rules related to (a) the CEMS Reference Method that governs the use of a Continuous Emissions Monitoring System; (b) alternative rules to those set out in documents incorporated by reference into these Regulations; and (c) the reporting, providing, recording and retention of information. 2 (1) The following definitions apply in these Regulations. Act means the Canadian Environmental Protection Act, 1999. (Loi) Alberta CEMS Code means the method entitled Continuous Emission Monitoring System (CEMS) Code (Pub. No.: Ref. 107) — published in May 1998 by Her Majesty the Queen in right of Alberta, as represented by the Minister responsible for Alberta Environmental Protection — as read in accordance with subsection (4). (Code SMECE de l’Alberta) alumina facility means a facility that is used or designed to produce alumina from bauxite for use in the production of aluminum. (installation de production d’alumine) aluminum facility means a facility that is used or designed (a) to produce aluminum from alumina; (b) to produce prebaked anodes for use in the production of aluminum; or (c) to calcinate petroleum coke for use in the production of aluminum. (aluminerie) asphalt refinery means a facility — other than a petroleum refinery — at which the annual volume of asphalt produced is greater than 33% of the annual volume of liquid petroleum products produced and that is used or designed to process, using distillation, (a) crude oil or bitumen; (b) blends of crude oil, or bitumen, with other hydrocarbon compounds; or (c) partially refined feedstock derived from crude oil or bitumen. (raffinerie d’asphalte) ASTM means ASTM International, formerly known as the American Society for Testing and Materials. (ASTM) ASTM D6522-11 means the method entitled Standard Test Method for Determination of Nitrogen Oxides, Carbon Monoxide, and Oxygen Concentrations in Emissions from Natural Gas-Fired Reciprocating Engines, Combustion Turbines, Boilers, and Process Heaters Using Portable Analyzers, published by ASTM. (méthode ASTM D6522-11) authorized official means (a) in respect of a responsible person who is an individual, that individual or another individual who is authorized to act on their behalf; (b) in respect of a responsible person that is a corporation, an officer of the corporation who is authorized to act on its behalf; and (c) in respect of a responsible person that is another entity, an individual who is authorized to act on its behalf. (agent autorisé) base metals facility means a pyrometallurgical or hydrometallurgical facility that is used or designed to recover or refine at least one of the following metals from feedstock that comes primarily from ore: (a) nickel; (b) copper; (c) zinc; (d) lead; (e) cobalt; and (f) chromium. (installation de production de métaux communs) boiler means combustion equipment — other than combustion equipment that is used only in the production of electricity for sale — that is used or designed to transfer thermal energy from the combustion of a fuel to water or steam or another fluid. (chaudière) cement manufacturing facility means a facility that is used or designed to produce clinker. (cimenterie) CEMS Reference Method means the EC CEMS Code or the Alberta CEMS Code. (méthode de référence des SMECE) CFR means Title 40, Chapter I of the Code of Federal Regulations of the United States. (CFR) chemicals facility means a facility that is used or designed to manufacture chemical substances from feedstock as its primary activity and where at least one of the following substances is manufactured: (a) adipic acid, esters of adipic acid, or amines of adipic acid; (b) titanium dioxide; (c) carbon black; (d) butyl rubber; (e) ethylene that is produced from refined petroleum, liquid hydrocarbons or natural gas; (f) ethylene glycol; (g) grain ethanol for use in industrial applications or as fuel; (h) linear alpha olefins; (i) ethylene-based polymers; (j) methanol; (k) iso-octane; (l) hydrogen that is produced, primarily for sale, from steam reforming; (m) linear alkyl benzene; (n) terephthalic acid; (o) paraxylene; (p) styrene or polystyrene; (q) sodium hydroxide; (r) citric acid; (s) nylon resins, fibres and filaments; and (t) nitric acid. (installation de fabrication de produits chimiques) Continuous Emission Monitoring System or CEMS means equipment for the sampling, conditioning and analyzing of emissions from a given source and the recording of data related to those emissions. (système de mesure et d’enregistrement en continu des émissions ou SMECE) diesel fuel means a fuel that can evaporate at atmospheric pressure, that boils at a temperature of at least 130ºC and at most 400ºC and that is for use in diesel engines. (carburant diesel) EC CEMS Code means the method entitled Protocols and Performance Specifications for Continuous Monitoring of Gaseous Emissions from Thermal Power Generation (EPS 1/PG/7) — published with revisions in December 2005 by Her Majesty the Queen in right of Canada, as represented by the Minister — as read in accordance with subsection (3). (Code SMECE d’EC) EC Method A means the method known as Method A: Determination of Sampling Site and Traverse Points in Reference Method EPS 1/RM/8. (méthode A de l’EC) EC Method B means the method known as Method B: Determination of Stack Gas Velocity and Volumetric Flow Rate in Reference Method EPS 1/RM/8. (méthode B de l’EC) EC Method D means the method known as Method D: Determination of Moisture Content in Reference Method EPS 1/RM/8. (méthode D de l’EC) engine means an engine that (a) when used, is stationary and is not in or on a machine that is self-propelled; (b) operates under characteristics significantly similar to the theoretical Otto combustion cycle; and (c) uses a spark plug or other sparking device. (moteur) EPA means the Environmental Protection Agency of the United States. (EPA) EPA Method 1 means the method entitled Method 1 — Sample and Velocity Traverses for Stationary Sources, set out in Appendix A-1 to Part 60 of the CFR. (méthode 1 de l’EPA) EPA Method 1A means the method entitled Method 1A — Sample and Velocity Traverses for Stationary Sources With Small Stacks or Ducts, set out in Appendix A-1 to Part 60 of the CFR. (méthode 1A de l’EPA) EPA Method 2 means the method entitled Method 2 — Determination of Stack Gas Velocity and Volumetric Flow Rate (Type S pitot tube), set out in Appendix A-1 to Part 60 of the CFR. (méthode 2 de l’EPA) EPA Method 3A means the method entitled Method 3A — Determination of Oxygen and Carbon Dioxide Concentrations in Emissions From Stationary Sources (Instrumental Analyzer Procedure), set out in Appendix A-2 to Part 60 of the CFR. (méthode 3A de l’EPA) EPA Method 4 means the method entitled Method 4 — Determination of Moisture Content in Stack Gases, set out in Appendix A-3 to Part 60 of the CFR. (méthode 4 de l’EPA) EPA Method 6C means the method entitled Method 6C — Determination of Sulfur Dioxide Emissions From Stationary Sources (Instrumental Analyzer Procedure), set out in Appendix A-4 to Part 60 of the CFR. (méthode 6C de l’EPA) EPA Method 7E means the method entitled Method 7E — Determination of Nitrogen Oxides Emissions from Stationary Sources (Instrumental Analyzer Procedure), set out in Appendix A-4 to Part 60 of the CFR. (méthode 7E de l’EPA) facility means the buildings, other structures and stationary equipment that are located on a single site or on adjacent sites that function as a single integrated site. (installation) gaseous fuel means a fuel that is gaseous at a temperature of 15.6ºC and an absolute pressure of 101.325 kPa. (combustible gazeux) gasoline means a petroleum distillate, or a blend of petroleum distillates, oxygenates or additives, that is suitable for use in a spark-ignition engine and that has the following characteristics, as determined by the applicable test method listed in the National Standard of Canada CAN/CGSB-3.5-2011, Automotive Gasoline: (a) a vapour pressure of at least 35 kPa; (b) an antiknock index of at least 80; (c) a distillation temperature, at which 10% of the fuel evaporates, of at least 35°C and at most 70°C; and (d) a distillation temperature, at which 50% of the fuel evaporates, of at least 60°C and at most 120°C. (essence) heater means combustion equipment, other than a boiler, that is used or designed to transfer thermal energy from the combustion of a fuel to a material that is being processed outside the combustion chamber. (four industriel) iron ore pelletizing facility means a facility that is used or designed to produce iron ore pellets from iron ore concentrate using an induration furnace. (installation de bouletage du minerai de fer) iron, steel and ilmenite facility means a facility — other than a foundry that produces iron or steel castings — that is used or designed to produce at least one of the following products: (a) metallurgical coke from coal; (b) titanium slag or iron from iron- or titanium-bearing ores or from iron ore pellets; and (c) steel from iron or scrap steel. (installation de production de fer, d’acier et d’ilménite) liquid petroleum product means (a) naphtha; (b) gasoline; (c) aviation turbine fuel; (d) kerosene; (e) diesel fuel; (f) light fuel oil; (g) heavy fuel oil; (h) naval distillate, bunker fuel or any other marine fuel; (i) gas oil; (j) lubricant basestock or petroleum-based lubricant; (k) asphalt; or (l) synthetic crude oil. (produit pétrolier liquide) nitrogen-based fertilizer facility means a facility that is used or designed to manufacture at least one of the following substances: (a) anhydrous ammonia, or aqueous ammonia, produced from steam methane reforming; and (b) urea. (installation de fabrication d’engrais à base d’azote) NOx means oxides of nitrogen, which is the sum of nitric oxide (NO) and nitrogen dioxide (NO2). (NOx) oil and gas facility means a facility, including an asphalt refinery or underground storage facility for gaseous fuel, that is used or designed (a) to extract hydrocarbons from underground deposits or reservoirs other than by means of thermal methods or surface mining; (b) to transport or process those hydrocarbons; (c) to transport or treat wastewater or waste that is related to the extraction or processing of those hydrocarbons for its injection underground; or (d) to inject that wastewater or waste underground. It does not include an oil sands facility, petroleum refinery, chemicals facility, nitrogen-based fertilizer facility or facility — other than an underground storage facility for gaseous fuel — that is primarily engaged in the local distribution of natural gas. (installation d’exploitation pétrolière et gazière) oil sands facility means a facility — other than a chemicals facility, nitrogen-based fertilizer facility or asphalt refinery — that is used or designed to engage in at least one of the following activities: (a) the surface mining of crude oil- or bitumen-containing sand from geological deposits; (b) the processing of that sand to separate crude oil or bitumen from that sand; (c) the extraction of crude oil or bitumen from underground deposits or reservoirs by means of thermal methods; and (d) the upgrading by means of the processing, using distillation, of crude oil or bitumen, or of blends of crude oil, or bitumen, with other hydrocarbon compounds, to produce a combined annual volume of gasoline, diesel fuel and lubricant basestock that is at most 40% of the facility’s annual volume of liquid petroleum products produced. (installation d’exploitation de sables bitumineux) operator means a person who has the charge, management or control of a boiler, heater, engine or cement manufacturing facility. (exploitant) petroleum refinery means a facility at which the combined annual volume of gasoline, diesel fuel and lubricant basestock produced is greater than 40% of the annual volume of liquid petroleum products produced and that is used or designed to process, using distillation, (a) crude oil or bitumen; (b) blends of crude oil, or bitumen, with other hydrocarbon compounds; or (c) partially refined feedstock derived from crude oil or bitumen. (raffinerie de pétrole) potash facility means a facility that is used or designed to produce potash, including a facility that is used or designed to extract potash-bearing ore. (installation de production de potasse) power plant means a facility that is used or designed to produce electricity for sale via the electric grid as its primary activity. (centrale électrique) ppmvd means parts per million, by volume on a dry basis. (ppmvs) pulp and paper facility means a facility that is used or designed to produce (a) pulp from wood or from other plant material or paper products; or (b) any product from pulp or a pulping process. (installation de production de pâte et papier) Reference Method EPS 1/RM/8 means the document entitled Reference Method for Source Testing: Measurement of Releases of Particulate from Stationary Sources, published in December 1993 by Her Majesty the Queen in right of Canada, as represented by the Minister. (Méthode de référence SPE 1/RM/8) responsible person means an owner or operator of a boiler or heater, an engine or a cement manufacturing facility. (personne responsable) SO2 means sulphur dioxide. (SO2) thermal method means a method of crude oil or bitumen extraction that involves the introduction of thermal energy into a geological formation in order to enhance the fluidity of crude oil or bitumen and to facilitate its extraction. It includes steam-assisted gravity drainage, cyclic steam stimulation, Toe-to-Heel Air Injection (THAI®), in situ combustion, flooding with heated water, solvent-assisted thermal methods and electro-thermal methods. (méthode thermique) underground storage facility for gaseous fuel means a facility — other than an oil sands facility, petrol refinery or asphalt facility — that is used or designed to store gaseous fuel underground. (installation de stockage souterrain de combustibles gazeux) year means a calendar year. (année) (2) For the purpose of interpreting any document that is incorporated by reference into these Regulations, “should” must be read to mean “must” and any recommendation or suggestion must be read as an obligation, unless the context requires otherwise. For greater certainty, the context of the accuracy or precision of a measurement can never require otherwise. (3) The EC CEMS Code is to be read as set out in Schedule 1. (4) The Alberta CEMS Code is to be read as set out in Schedule 2. (5) Any EPA method that is incorporated by reference into these Regulations must be read without reference to the exercise of discretion by the EPA or by the Administrator of the EPA. (6) In the event of an inconsistency between a provision of these Regulations and a document that is incorporated by reference into these Regulations, the provision prevails to the extent of the inconsistency. (7) Any method of the EPA, ASTM or GPA that is incorporated by reference into these Regulations is incorporated as amended from time to time. 3 Unless the context requires that a particular responsible person complies, a requirement set out in these Regulations in respect of, respectively, a boiler or heater, an engine or a cement manufacturing facility, including a requirement in respect of a kiln located in it, must be complied with by a responsible person for the boiler or heater, engine or cement manufacturing facility. 4 The following definitions apply in this Part and in Schedules 3 to 7. alternative gas means a gaseous fossil fuel other than natural gas. (gaz de remplacement) amendment day means the day on which the Regulations Amending the Multi-Sector Air Pollutants Regulations (Part 1 — Biomass) come into force. (date de modification) anode-baking furnace means a heater that bakes green anodes to produce blocks of carbon for use in the production of aluminum. (four de cuisson d’anodes) ASTM D1945-03 means the method entitled Standard Test Method for Analysis of Natural Gas by Gas Chromatography, published by ASTM. (méthode ASTM D1945-03) ASTM D1946-90 means the method entitled Standard Practice for Analysis of Reformed Gas by Gas Chromatography, published by ASTM. (méthode ASTM D1946-90) biomass means a liquid or solid fuel that consists only of non-fossilized organic material that originates from plants or animals but does not come from a geological formation, including (a) liquid and solid products or waste produced from that material; (b) liquids and solids recovered from that material, including from organic waste; and (c) sludge from wastewater treatment. (biomasse) biomass boiler means (a) a boiler that can reach at least 50% of its rated capacity when it is in a steady state and at least 90% of the input energy in its combustion chamber results from the introduction of biomass; and (b) in the case of a boiler that is commissioned or recommissioned on or after amendment day, a boiler that is linked to equipment that is capable of introducing a sufficient quantity of biomass as the input energy in its combustion chamber to allow it to meet the criteria set out in paragraph (a). (chaudière à biomasse) biomass heater means (a) a heater that can reach at least 50% of its rated capacity when it is in a steady state and at least 90% of the input energy in its combustion chamber results from the introduction of biomass; and (b) in the case of a heater that is commissioned or recommissioned on or after amendment day, a heater that is linked to equipment that is capable of introducing a sufficient quantity of biomass as the input energy in its combustion chamber to allow it to meet the criteria set out in paragraph (a). (four industriel à biomasse) blast furnace stove means a vertical cylindrical regenerator filled with refractory and used to preheat ambient air that is then introduced into a blast furnace used in ironmaking. (récupérateur de haut fourneau) CEMS test means a determination, by means of a CEMS in accordance with section 32, of the NOx emission intensity of a boiler or heater. (essai SMECE) chemical recovery boiler means a boiler whose fuel includes spent pulping liquor and that recovers chemical constituents from the combustion of that spent pulping liquor. (chaudière de récupération chimique) class 40, in relation to a pre-existing boiler or heater, describes a class 40 boiler or heater within the meaning of section 12. (classe 40) class 70, in relation to a pre-existing boiler or heater, describes a class 70 boiler or heater within the meaning of section 12. (classe 70) class 80, in relation to a pre-existing boiler or heater, describes a class 80 boiler or heater within the meaning of section 12. (classe 80) coke oven means an oven that converts coal to coke through distillation. (four à coke) coke oven battery means a heater that consists of a combustion chamber, with more than one burner, whose exhaust gas circulate between coke ovens. (batterie de fours à coke) commercial grade natural gas means natural gas that is supplied by a commercial supplier. (gaz naturel de qualité commerciale) commissioning date means the day on which a boiler or heater begins to produce thermal energy primarily for use in production or to provide heat. (date de mise en service) ethylene cracker means a heater that transforms a mixture of steam and hydrocarbons into hydrocarbon gases, notably ethylene. (craqueur d’éthylène) gaseous fossil fuel includes gaseous fossil fuel that is a by-product of an industrial process, or industrial operation, and that has constituents with thermal energy value. (combustible fossile gazeux) GPA  means the GPA Midstream Association, formerly known as the Gas Processors Association. (GPA) GPA 2261-25  means the method entitled Analysis for Natural Gas and Similar Gaseous Mixtures by Gas Chromatography, published by GPA. (méthode GPA 2261-25) GPA 2286-24  means the method entitled Method for the Extended Analysis of Natural Gas and Similar Gaseous Mixtures by Temperature Program Gas Chromatography, published by GPA.  (méthode GPA 2286-24) heat-recovery steam generator means equipment that captures useful thermal energy from the hot exhaust gas of a gas turbine, or from a set of reciprocating engines, to produce steam. (générateur de vapeur à récupération de chaleur) modern, in relation to a boiler or heater, describes a boiler or heater that is not transitional whose commissioning date is on or after the day on which these Regulations are registered. (moderne) natural gas means a gaseous fossil fuel that consists of at least 90% methane by volume. (gaz naturel) NOx emission intensity means the quantity of NOx emitted by a boiler or heater, expressed in grams of NOx emitted per gigajoule of thermal energy in the fuel (g/GJ), based on the higher heating value of the fuel combusted. (intensité d’émission de NOx) packaged, in relation to a boiler or heater, describes a boiler or heater that is received at the facility in a state of near-complete assembly and that requires, at the facility, (a) assembling any prefabricated components; (b) fixing it to its location; and (c) making the connections necessary for its operation. (préfabriqué) pre-existing, in relation to a boiler or heater, describes a boiler or heater whose commissioning date is before the day on which these Regulations are registered. (préexistant) preheated air means air that is preheated above ambient air temperature before it is introduced into the combustion chamber of a boiler or heater. (air préchauffé) rated capacity means (a) in relation to a pre-existing boiler or heater, the lesser of the following, expressed in GJ/h, as specified on the nameplate affixed to the boiler or heater or, in the absence of such a nameplate, as set out in a document provided by the manufacturer: (i) the maximum thermal energy — based on the higher heating value of the fuel combusted — that the boiler or heater was capable of producing in an hour on its commissioning date, and (ii) the maximum thermal energy — based on the higher heating value of the fuel combusted — that the boiler or heater is capable of producing in an hour; and (b) in relation to any other boiler or heater, the maximum thermal energy — based on the higher heating value of the fuel combusted — that the boiler or heater is capable of producing in an hour, expressed in GJ/h, as specified on the nameplate affixed to the boiler or heater or, in the absence of such a nameplate, as set out in a document provided by the manufacturer. (capacité nominale) recommissioning date means the day on which a boiler or heater begins to produce thermal energy primarily for use in production or to provide heat after (a) a major modification referred to in subsection 13(2); or (b) a redesign referred to in paragraph 10(2)(b). (date de remise en service) reheat furnace means a heater in which steel is reheated for hot rolling into basic shapes. (four de réchauffage) stack test means a determination, in accordance with sections 27 to 31, of the NOx emission intensity of a boiler or heater. (essai en cheminée) standard m3 has the meaning assigned to a cubic metre at standard pressure and standard temperature by the definition standard volume in subsection 2(1) of the Electricity and Gas Inspection Regulations. (m3 normalisé) steady state means an operating state that is other than start-up, shutdown or upset. (état stable) steam methane reformer means a heater that transforms a mixture of steam and hydrocarbons in the presence of a catalyst to produce hydrogen and carbon oxides and includes — if it shares a common stack with the heater — any integrated auxiliary boiler that is used to produce that steam or other integrated equipment that heats that steam. (reformeur de méthane à la vapeur) transitional, in relation to a boiler or heater, describes a boiler or heater that is located in a regulated facility set out in subsection 5(2) on its commissioning date and whose commissioning date occurs in the period that begins on the day on which these Regulations are registered and ends (a) if the boiler or heater is packaged, three months after that day; and (b) in any other case, 36 months after that day. (de transition) 5 (1) This Part applies in respect of a pre-existing, transitional or modern boiler or heater located in a regulated facility that is used or designed to combust gaseous fossil fuel and that has a rated capacity of at least 10.5 GJ/h. (2) The following are the regulated facilities: (a) oil and gas facilities; (b) oil sands facilities; (c) chemicals facilities; (d) nitrogen-based fertilizer facilities; (e) pulp and paper facilities; (f) base metals facilities; (g) potash facilities; (h) alumina facilities and aluminum facilities; (i) power plants; (j) iron, steel and ilmenite facilities; (k) iron ore pelletizing facilities; and (l) cement manufacturing facilities. (3) Despite subsections (1) and (2), this Part does not apply in respect of the following types of boiler or heater: (a) a heater that is used to dry, bake or calcinate materials, including a kiln as defined in section 101 and an anode-baking furnace; (b) a heater that is used in any process to chemically transform ore or intermediate products into bulk metallic products; (c) a coke oven battery; (d) a heater or boiler that is designed to combust coke oven gas; (e) a blast furnace stove; (f) a heater or boiler that is designed to combust blast furnace gas; (g) an ethylene cracker; (h) a steam methane reformer; (i) a reheat furnace; (j) a boiler or heater that is used only for activities that are subsequent to the hot rolling of steel into basic shapes at an iron, steel and ilmenite facility; (k) a chemical recovery boiler; (l) a biomass boiler or biomass heater; (m) a heat-recovery steam generator; (n) a boiler that combusts exhaust gases that arise from the partial combustion of coke in a vessel integrated with a fluid coking unit; and (o) a boiler or heater that is used only in the start-up of a facility or process and operated for fewer than 500 hours in each previous year of its operation. (4) For the purpose of paragraph (3)(l), the percentage of the input energy in a biomass boiler’s or biomass heater’s combustion chamber resulting from the introduction of biomass is to be determined, for a given hour while the boiler or heater is in a steady state, by the formula is the input energy resulting from the introduction of biomass for the given hour, determined by the formula is the quantity of the biomass combusted during the given hour, as measured by a flow meter on the input, expressed in kl for liquid biomass and in t for solid biomass, and is the higher heating value of the biomass combusted during the given hour, expressed in GJ/kl for liquid biomass and in GJ/t for solid biomass, being the higher heating value determined in accordance with any of the required HHV methods set out in section 22 that apply, or the default higher heating value set out in column 2 of the applicable table to Schedule 3 for the type of fuel set out in column 1; is the input energy resulting from the introduction of commercial grade natural gas for the given hour, determined by the formula is the quantity of the commercial grade natural gas combusted during the given hour, as measured by a flow meter on the input, expressed in standard m3, and is the higher heating value of the commercial grade natural gas combusted during the given hour, expressed in GJ/standard m3, being the higher heating value determined in accordance with any of the required HHV methods set out in section 22 that apply, or 0.03793; is the input energy resulting from the introduction of gaseous fossil fuel, other than commercial grade natural gas, for the given hour, determined by the formula is the quantity of the gaseous fossil fuel, other than commercial grade natural gas, combusted during the given hour, as measured by a flow meter on the input, expressed in standard m3, and is the higher heating value of the gaseous fossil fuel, other than commercial grade natural gas, combusted during the given hour, expressed in GJ/standard m3, determined in accordance with any of the required HHV methods set out in section 22 that apply; is the input energy resulting from the introduction of a fuel other than biomass or gaseous fossil fuel during the given hour, determined by the formula is the quantity of the ith fuel, other than gaseous fossil fuel, combusted during the given hour, as measured by a flow meter on the input, expressed in standard m3 for gaseous fuels, in kl for liquid fuels and in t for solid fuels, is the higher heating value of the ith fuel, other than gaseous fossil fuel, combusted during the given hour, expressed in GJ/standard m3 for gaseous fuels, in GJ/kl for liquid fuels and in GJ/t for solid fuels, being the higher heating value determined in accordance with any of the required HHV methods set out in section 22 that apply, or the default higher heating value set out in column 2 of the applicable table to Schedule 3 for the type of fuel set out in column 1, and is the ith fuel, other than biomass or gaseous fossil fuel, combusted, where i goes from 1 to n and where n is the number of those fuels combusted; and is the input energy, expressed in GJ, that originates from a source other than the combustion of fuel in the boiler’s or heater’s combustion chamber during the given hour, determined in accordance with generally accepted engineering principles. (5) A responsible person for a biomass boiler or biomass heater must, on the Minister’s request, provide to the Minister any of the following: (a) information and supporting documents obtained from the manufacturer of the boiler or heater that demonstrates that it is a biomass boiler or biomass heater, as the case may be; or (b) the results of a field test that (i) was conducted for a period of at least one hour, by a person who is independent of all responsible persons for the boiler or heater and demonstrates that the boiler or heater is a biomass boiler or biomass heater, as the case may be, and that the percentage referred to in subsection (4) has been determined in accordance with that subsection, and (ii) is supported by documents in the possession of a responsible person for the boiler or heater that establish that the independent person referred to in subparagraph (i) (A) is an engineer who is, under the laws of the province in which the biomass boiler or biomass heater is located, authorized to practise engineering in relation to combustion equipment, or (B) has demonstrated knowledge of, and at least five years’ experience as the technical lead of projects that involved, the design of combustion equipment. 6 (1) Subject to section 10, the NOx emission intensity of a modern boiler that, for a given hour, has at least 50% of the input energy in its combustion chamber resulting from the introduction of gaseous fossil fuel set out in column 1 of the table to this subsection and that has a thermal efficiency set out in column 2 must not, for that hour, exceed the limit set out in column 3. (2) For the purpose of subsection (1), the thermal efficiency of a modern boiler for the given hour (a) if there has been a determination made in accordance with section 18, is the result of the most recent such determination; and (b) in any other case, is deemed to be less than 80%. 7 (1) Subject to section 10, the NOx emission intensity of a modern heater — that, for a given hour, has at least 50% of the input energy in its combustion chamber resulting from the introduction of gaseous fossil fuel set out in column 1 of the table to this subsection and that has a difference between the temperature of its preheated air and the ambient air set out in column 2 must not, for that hour, exceed the limit set out in column 3. (2) For the purpose of subsection (1), the difference between the temperature of a modern heater’s preheated air and the ambient air, expressed in °C, for the given hour (a) if there has been a determination of that difference made in accordance with section 24 within the previous 12 months, is the result of the most recent of such determination; and (b) in any other case, is deemed to be 0°C. 8 For the purpose of determining the type of gaseous fossil fuel — natural gas or alternative gas — introduced into the combustion chamber of a boiler or heater, the percentage of methane in the fuel must be determined in accordance with section 16. 9 The NOx emission intensity of a transitional boiler or heater that, for a given hour, has at least 50% of the input energy in its combustion chamber resulting from the introduction of gaseous fossil fuel must not, for that hour, exceed the following limit: (a) 26 g/GJ, if the boiler or heater has a rated capacity of at least 10.5 GJ/h and at most 105 GJ/h; and (b) subject to section 10, 40 g/GJ, if the boiler or heater has a rated capacity greater than 105 GJ/h. 10 (1) The NOx emission intensity of a redesigned boiler or heater that, for a given hour, has at least 50% of the input energy in its combustion chamber resulting from the introduction of gaseous fossil fuel must not, for that hour, exceed the limit of 26 g/GJ. (2) A redesigned boiler or heater is one that (a) on its commissioning date, was not designed to combust gaseous fossil fuel; and (b) after the day on which these Regulations are registered, is redesigned to combust, on its recommissioning date, gaseous fossil fuel. 11 The NOx emission intensity of a pre-existing boiler or heater that is class 80 or class 70 — other than those referred to in subsections 13(1) and 14(1) and (2) — and that, for a given hour, has at least 50% of the input energy in its combustion chamber resulting from the introduction of gaseous fossil fuel must not, for that hour, exceed the limit of 26 g/GJ, as of (a) January 1, 2026, for a class 80 boiler or heater; and (b) January 1, 2036, for a class 70 boiler or heater. 12 (1) A pre-existing boiler or heater is classified — in accordance with its classification NOx emission intensity determined in accordance with subsection 34(1) or redetermined under subsection 36(1) or 36.1(1) — as follows: (a) class 80, if its classification NOx emission intensity is determined to be at least 80 g/GJ; (b) class 70, if its classification NOx emission intensity is determined to be at least 70 g/GJ and less than 80 g/GJ; and (c) class 40, in any other case. (2) A pre-existing boiler or heater — other than a redesigned boiler or heater referred to in subsection 10(2) — that is not classified under subsection (1) is deemed to be class 80 and to have a classification NOx emission intensity of 80 g/GJ. 13 (1) Subject to section 14, the NOx emission intensity of a class 80 or class 70 boiler or heater that has undergone a major modification before, respectively, January 1, 2026 or January 1, 2036 must not, as of its recommissioning date — for each hour during which at least 50% of the input energy in its combustion chamber results from the introduction of gaseous fossil fuel — exceed the limit of 26 g/GJ. (2) A major modification is (a) for a boiler or heater with a single burner or double burner, the replacement of a burner; (b) for a boiler or heater that has at least three burners, the replacement, within a period of at most 60 months, of at least three burners; (c) the addition of a burner; or (d) the relocation of a boiler or heater. 14 (1) The NOx emission intensity of a class 80 or class 70 boiler or heater that undergoes a major modification that involves the use of combustion modification techniques must, as of its recommissioning date following the major modification, not — for each hour during which at least 50% of the input energy in its combustion chamber results from the introduction of gaseous fossil fuel — exceed the limit of 50% of its classification NOx emission intensity, if (a) before the major modification is carried out, a responsible person for the boiler or heater provides to the Minister (i) the name of the manufacturer of the boiler or heater, along with its serial number, make and model and the information referred to in section 1 of Schedule 6, (ii) documents, provided to the responsible person by a person who is independent of them, that establish that the NOx emission intensity of the boiler or heater could not be at most 26 g/GJ when it operates under (A) any circumstances that include the use of combustion modification techniques, and (B) the conditions set out in subsection 27(2), (iii) a signed certificate, provided to the responsible person by another person who is independent of both the responsible person and the independent person referred to in subparagraph (ii), that indicates that that other person has reviewed the documents described in subparagraph (ii) and agrees that the documents establish that the NOx emission intensity of the boiler or heater could not be at most 26 g/GJ when it operates under the circumstances and conditions described in subparagraph (ii), and (iv) documents that establish that each of the independent persons referred to in subparagraphs (ii) and (iii) (A) is an engineer who is, under the laws of the province in which the boiler or heater is located, authorized to practise engineering in relation to combustion modification techniques, or (B) has demonstrated knowledge of, and at least five years’ experience as the technical lead of projects that involved, the design of combustion modification techniques; and (b) after that recommissioning date, the NOx emission intensity of the boiler or heater is more than 26 g/GJ. (2) The NOx emission intensity of a class 80 or class 70 boiler or heater referred to in clause 34(1)(b)(i)(B) that has undergone a major modification that involved the use of combustion modification techniques must, as of the day that is 12 months after the day on which these Regulations are registered, not — for each hour during which at least 50% of the input energy in its combustion chamber results from the introduction of gaseous fossil fuel — exceed the limit of 50% of its classification NOx emission intensity, if (a) before that day, a responsible person for the boiler or heater provides the Minister with the information set out in subparagraphs (1)(a)(i) to (iv); and (b) after the boiler’s or heater’s recommissioning date, the NOx emission intensity of the boiler or heater is more than 26 g/GJ. (3) For the purpose of this section, combustion modification techniques are techniques to reduce the formation of thermal NOx in the combustion chamber of a boiler or heater by modifying the combustion process. They include the use of low-NOx burners and of flue gas recirculation. 15 The percentage of the input energy in a boiler’s or heater’s combustion chamber resulting from the introduction of gaseous fossil fuel, for a given hour while the boiler or heater is in a steady state, must be determined by the formula is the input energy resulting from the introduction of commercial grade natural gas for the given hour, determined by the formula is the quantity of the commercial grade natural gas combusted during the given hour, as measured by a flow meter on the input, expressed in standard m3, and is the higher heating value of the commercial grade natural gas combusted during the given hour, expressed in GJ/standard m3, being the higher heating value determined in accordance with any of the required HHV methods set out in section 22 that apply, or 0.03793; is the input energy resulting from the introduction of gaseous fossil fuel, other than commercial grade natural gas, for the given hour, determined by the formula is the quantity of the gaseous fossil fuel, other than commercial grade natural gas, combusted during the given hour, as measured by a flow meter on the input, expressed in standard m3, and is the higher heating value of the gaseous fossil fuel, other than commercial grade natural gas, combusted during the given hour, expressed in GJ/standard m3, determined in accordance with any of the required HHV methods set out in section 22 that apply; is the input energy resulting from the introduction of a fuel other than gaseous fossil fuel during the given hour, determined by the formula is the quantity of the ith fuel other than gaseous fossil fuel combusted during the given hour as measured by a flow meter on the input, expressed in a given unit, is the higher heating value of the ith fuel other than gaseous fossil fuel combusted during the given hour, expressed in GJ/the given unit, being the higher heating value determined in accordance with any of the required HHV methods set out in section 22 that apply, or the default higher heating value set out in column 2 of the applicable table to Schedule 3 for the type of fuel set out in column 1 of that table, and is the ith fuel other than gaseous fossil fuel combusted, where i goes from 1 to n and where n is the number of those fuels combusted; and is the input energy, expressed in GJ, that originates from a source other than the combustion of fuel in the boiler’s or heater’s combustion chamber during the given hour, determined in accordance with generally accepted engineering principles. 16 (1) The percentage of methane in the gaseous fossil fuel introduced into the combustion chamber of a boiler or heater, for a given hour, must be determined, by volume, as a weighted average by the formula is the concentration of methane, determined in accordance with subsection (2), in the natural gas introduced into the combustion chamber during the given hour, expressed as a decimal fraction; is the quantity of the natural gas introduced into the combustion chamber during the given hour, as measured by a flow meter on the input, expressed in standard m3; is the concentration of methane, determined in accordance with subsection (2), in the alternative gas introduced into the combustion chamber during the given hour, expressed as a decimal fraction; and is the quantity of the alternative gas introduced into the combustion chamber during the given hour, as measured by a flow meter on the input, expressed in standard m3. (2) The concentration of methane in the gaseous fossil fuel introduced into the combustion chamber is (a) for commercial grade natural gas, either (i) to be determined in accordance with ASTM D1945-03, ASTM D1946-90, GPA 2261-25 or GPA 2286-24 , or (ii) fixed as 95%; and (b) for any other gaseous fossil fuel, to be determined in accordance with ASTM D1945-03, ASTM D1946-90, GPA 2261-25 or GPA 2286-24, whichever applies. 17 If the concentration of methane in the commercial grade natural gas introduced into the combustion chamber is fixed as 95%, in accordance with subparagraph 16(2)(a)(ii), the higher heating value of the commercial grade natural gas must, for the purpose of paragraph 29(b), be fixed as 0.03793 in accordance with subparagraph (a)(ii) of the description of HHVi in that paragraph. 18 The thermal efficiency of a modern boiler, for a given day, must be determined by the formula is the percentage of loss of thermal efficiency due to the thermal energy contained in the boiler’s flue gas determined on a dry basis for an hour in the given day, determined in accordance with section 19; is the percentage of loss of thermal efficiency due to the thermal energy contained in the water in the boiler’s flue gas for an hour in the given day, determined in accordance with section 20; is the percentage of loss of thermal efficiency due to radiation and to convection of the boiler’s surfaces for an hour in the given day, being for a watertube boiler, the percentage of loss of thermal efficiency that is set out in, as applicable, column 2, 3 or 4 of Schedule 4, if the boiler operates during that hour at, respectively, 100%, 80% or 60% of its rated capacity, for the rated capacity of the boiler set out in column 1 of that Schedule and for that percentage , or interpolated on a linear basis from the rated capacity of the boiler within the applicable range of rated capacities as between two consecutive rows of rated capacities set out in column 1 of Schedule 4, and the percentage of loss of thermal efficiency at which the boiler operates during that hour as set out in the range between the percentages set out in columns 2 and 3 of Schedule 4, if it operates between 100% and 80% of its rated capacity, or the range between percentages set out in columns 3 and 4 of that Schedule, if it operates between 80% and 60% of its rated capacity, for a firetube boiler, 0.5%, and in any other case, 1%; and is the percentage of loss of thermal efficiency due to other sources, which is deemed to be 0.1%. 19 Ldfg referred to in section 18 must be determined for an hour in the given day by the formula is the average temperature, expressed in °C, of the flue gas, as measured in the stack, during that hour; is the average temperature , expressed in °C, of the air introduced into the combustion chamber during that hour; is the higher heating value of the fuel combusted during that hour, expressed on a mass basis in kJ/kg, being for commercial grade natural gas, the higher heating value, determined in accordance with any of the required HHV methods set out in section 22 that apply, or 51 800 kJ/kg, and in any other case, the weighted average of the higher heating value of each fuel combusted during that hour, expressed on a mass basis in kJ/kg, determined in accordance with any of the required HHV methods set out in section 22 that apply; and is the average ratio of the mass of the flue gas to the mass of the fuel combusted, expressed in kg/kg, during that hour, determined by the formula is the percentage of oxygen, determined by volume on a dry basis, in the flue gas, determined in accordance with EPA Method 3A or ASTM D6522-11, is the ratio of the stoichiometric mass of the flue gas to the mass of the fuel combusted, expressed in kg/kg, being for commercial grade natural gas, the ratio determined in accordance with paragraph (b), or 15.3 kg/kg, and in any other case, the ratio determined by the formula: is the concentration of carbon in the fuel combusted, expressed in kg of carbon per kg of that fuel, is the concentration of hydrogen in the fuel combusted, expressed in kg of hydrogen per kg of that fuel, is the concentration of nitrogen in the fuel combusted, expressed in kg of nitrogen per kg of that fuel, is the concentration of sulphur in the fuel combusted, expressed in kg of sulphur per kg of that fuel, and is the concentration of oxygen in the fuel combusted, expressed in kg of oxygen per kg of that fuel. 20 Lw referred to in section 18 must be determined for an hour of the given day by the formula is the concentration of hydrogen in the fuel combusted during that hour, expressed in kg of hydrogen per kg of that fuel, being for commercial grade natural gas, a weighted average calculated on the basis of the concentration — expressed in kg/kg — of each of the constituents of the commercial grade natural gas, as determined in accordance with ASTM D1945-03, ASTM D1946-90, GPA 2261-25 or GPA 2286-24, or 0.237 kg/kg, and in any other case, the concentration determined in accordance with subsections 23(1) and (2); is the average temperature, expressed in °C, of the flue gas, as measured in the stack during that hour; is the average temperature, expressed in °C, of the air introduced into the combustion chamber during that hour; and is the higher heating value of the fuel combusted during that hour, expressed on a mass basis in kJ/kg, being for commercial grade natural gas, the higher heating value determined in accordance with any of the required HHV methods set out in section 22 that apply, or 51 800 kJ/kg, and in any other case, the weighted average of the higher heating value of each fuel introduced into the combustion chamber, expressed on a mass basis in kJ/kg, determined in accordance with any of the required HHV methods set out in section 22 that apply; 21 The value for commercial grade natural gas for HHVm in sections 19 and 20, for Ms in section 19 and for H in section 20 must all be either (a) determined (i) for H, as a weighted average calculated on the basis of determinations made in accordance with the one of the ASTM methods referred to in subparagraph (a)(i) of H, (ii) for HHVm, in accordance with subparagraph (a)(i) of HHVm, and (iii) for Ms, by the formula set out in paragraph (b) of Ms; or (b) fixed as the applicable ratio referred to, respectively, in H, HHVm and Ms. 22 The required HHV methods are (a) for gaseous fuels, as applicable, (i) the ASTM D1826-94 method entitled Standard Test Method for Calorific (Heating) Value of Gases in Natural Gas Range by Continuous Recording Calorimeter, published by ASTM, (ii) the ASTM D3588-98 method entitled Standard Practice for Calculating Heat Value, Compressibility Factor, and Relative Density of Gaseous Fuels, published by ASTM, (iii) the ASTM D4891-89 method entitled Standard Test Method for Heating Value of Gases in Natural Gas Range by Stoichiometric Combustion, published by ASTM, and (iv) the method GPA Standard 2172-25 entitled Calculation of Gross Heating Value, Relative Density, Compressibility and Theoretical Hydrocarbon Liquid Content for Natural Gas Mixtures for Custody Transfer, published by GPAn; (b) for liquid fuels, as applicable, (i) the ASTM D240-09 method entitled Standard Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb Calorimeter, published by ASTM, and (ii) the ASTM D4809-09ae1 method entitled Standard Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb Calorimeter (Precision Method), published by ASTM; and (c) for solid fuels, as applicable, (i) the ASTM D5865-12 method entitled Standard Test Method for Gross Calorific Value of Coal and Coke, published by ASTM, and (ii) the ASTM D5468-02 method entitled Standard Test Method for Gross Calorific and Ash Value of Waste Materials, published by ASTM. 23 (1) The concentration of carbon, hydrogen, nitrogen, sulphur and oxygen per kilogram of fuel introduced into the combustion chamber must be determined as a weighted average of the concentration of each of the constituents of each fuel in accordance with subsection (2). (2) The concentration of the constituents of fuel must be determined (a) for gaseous fuels, in accordance with, as applicable, (i) ASTM D1945-03, (ii) ASTM D1946-90, (iii) GPA 2261-25, and (iv) GPA 2286-24; (b) for liquid fuels, (i) in the case of the concentration of carbon, hydrogen and nitrogen, in accordance with the ASTM D5291-10 method entitled Standard Test Methods for Instrumental Determination of Carbon, Hydrogen, and Nitrogen in Petroleum Products and Lubricants, published by ASTM, (ii) in the case of the concentration of sulphur, in accordance with the ASTM D4294-10 method entitled Standard Test Method for Sulfur in Petroleum and Petroleum Products by Energy Dispersive X-ray Fluorescence Spectrometry, published by ASTM, and (iii) in the case of the concentration of oxygen, to be the remaining concentration after removing the determinations made for the concentrations of carbon, hydrogen, nitrogen and sulphur; and (c) for solid fuel that (i) is coal or coke, (A) in the case of the concentration of carbon, hydrogen and nitrogen, in accordance with the ASTM D5373-08 method entitled Standard Test Methods for Instrumental Determination of Carbon, Hydrogen, and Nitrogen in Laboratory Samples of Coal, published by ASTM, (B) in the case of the concentration of sulphur, in accordance with the ASTM D4239-12 method entitled Standard Test Method for Sulfur in the Analysis Sample of Coal and Coke Using High-Temperature Tube Furnace Combustion, published by ASTM, and (C) in the case of the concentration of oxygen, to be the remaining concentration after removing the determinations made for the concentrations of carbon, hydrogen, nitrogen and sulphur, and (ii) is derived from waste, (A) in the case of the concentration of carbon and hydrogen, in accordance with the ASTM E777-08 method entitled Standard Test Method for Carbon and Hydrogen in the Analysis Sample of Refuse-Derived Fuel, published by ASTM, (B) in the case of the concentration of nitrogen, in accordance with the ASTM E778-08 method entitled Standard Test Methods for Nitrogen in the Analysis Sample of Refuse-Derived Fuel, published by ASTM , (C) in the case of the concentration of sulphur, in accordance with the ASTM E775-87(2008)e1 method entitled Standard Test Methods for Total Sulfur in the Analysis Sample of Refuse-Derived Fuel, published by ASTM, and (D) in the case of the concentration of oxygen, to be the remaining concentration after removing the determinations made for the concentrations of carbon, hydrogen, nitrogen and sulphur. 24 For a modern heater that is equipped to preheat air, the difference between the temperature of its preheated air and the ambient air, for a given hour, must be determined by the formula is the average temperature, expressed in °C, of the heater’s preheated air introduced into the combustion chamber during the given hour, as measured at the point of introduction to the combustion chamber; and is the average temperature, expressed in °C, of the ambient air introduced into the preheater during the given hour, as measured at the point of introduction to the air preheater. 25 The NOx emission intensity of a boiler or heater must be determined by means of (a) a stack test or a CEMS test, if (i) the boiler’s or heater’s rated capacity is at most 262.5 GJ/h, or (ii) the boiler’s or heater’s rated capacity is more than 262.5 GJ/h and its NOx emission intensity was less than 80% of the NOx emission intensity limit applicable to it under any of sections 6, 7, 9 to 11, 13 and 14, as determined by means of one or more stack tests during (A) its initial test conducted under section 33, and (B) each of the first two compliance tests conducted under subparagraph 38(2)(c)(i); and (b) subject to subsections 26(1) and paragraphs 33(2)(a) and 38(2)(a), a CEMS test in any other case. 26 (1) The NOx emission intensity of a boiler or heater that is to be determined under paragraph 25(b) must be determined for a given hour in accordance with subsection (2), if the boiler or heater (a) is not equipped with a CEMS; and (b) has been identified under subsection (5) with another boiler or heater whose NOx emission intensity is determined for that given hour by means of a CEMS test as a rolling hourly average. (2) The NOx emission intensity of a boiler or heater referred to in paragraph (1)(a) for each hour is the greater of (a) the result of a stack test that is applicable to that hour, and (b) the rolling hourly average for that hour determined by means of a CEMS test conducted on the other boiler or heater referred to in paragraph (1)(b). (3) A boiler or heater referred to in paragraph (1)(a) may be identified with another boiler or heater referred to in paragraph (1)(b) if the following conditions are met: (a) they have the same manufacturer; (b) they have the same rated capacity; (c) they are designed to have the same NOx emission intensity; (d) they have the same equipment to preheat air, if any; (e) they combust fuel from a common source; (f) they are juxtaposed; and (g) they are (i) both class 80, (ii) both class 70, (iii) both transitional or modern, or one is transitional and the other is modern, or (iv) both redesigned within the meaning of paragraph 10(2)(b). (4) The identification is made as of (a) for class 80 boilers or heaters that underwent a major modification, the recommissioning date of the boiler or heater referred to in paragraph (1)(a); (b) for class 70 boilers or heaters, the earlier of (i) the recommissioning date of the boiler or heater referred to in paragraph (1)(a), if it underwent a major modification, and (ii) January 1, 2036; (c) for transitional or modern boilers or heaters, the commissioning date of the boiler or heater referred to in paragraph (1)(a); and (d) for redesigned boilers or heaters referred to in section 10, the recommissioning date of the boiler or heater referred to in paragraph (1)(a). (5) The identification is made on the recording of the following information: (a) the name of the manufacturer — along with the serial number, make and model — of the boiler or heater referred to in paragraph (1)(a); (b) the name of the manufacturer — along with the serial number, make and model — of the other boiler or heater referred to in paragraph (1)(b); (c) documentation that establishes that those boilers or heaters meet the conditions set out in paragraphs (3)(b) to (g); (d) an indication that the boiler or heater referred to in paragraph (a) is identified with the boiler or heater referred to in paragraph (b); and (e) the date of the recording. (6) At most four boilers or heaters may be identified under subsection (5) with a given other boiler or heater referred to in paragraph (1)(b). 26.1 (1) A stack test or CEMS test at a common stack may be used to determine the NOx emission intensity for all of the boilers and heaters that share the common stack and are operating during the test. (2) For the purposes of sections 34 and 36, if the only devices that share a common stack and are operating during a stack test or CEMS test are boilers or heaters, the result of that test applies when determining the NOx emission intensity of each of those boilers or heaters. (3) For the purposes of sections 34 and 36, if a boiler or heater shares a common stack with a device to which this Part does not apply and that is operating during the test, the NOx emission intensity of that boiler or heater is determined by the formula is the energy, expressed in GJ, of the fuel combusted during the test by the rth boiler or heater; is the NOx emission intensity measured during the test, expressed in g/GJ; is the energy, expressed in GJ, of the fuel combusted during the test by the uth device; is the manufacturer’s guaranteed NOx emission intensity value, expressed in g/GJ for the uth device or, if the manufacturer has not provided such a guarantee, 26 g/GJ; is the rth boiler or heater to which this Part applies that is operating at the common stack during the test, where r goes from 1 to n and n is the number of boilers or heaters that meet those criteria; and is the uth device to which this Part does not apply that is operating at the common stack during the test, where u goes from 1 to n and n is the number of devices that meet those criteria. (4) For greater certainty, if subsection (2) or (3) applies with respect to section 34, the stack test or CEMS test must have been conducted during the reference period described in subsection 34(1). (5) For the purposes of sections 33 and 38, the NOx emission intensity of a boiler or heater that shares a common stack with any other device is deemed not to exceed the applicable limit set out in section 6, 7, 9 to 11, 13 or 14 if the NOx emission intensity of the common stack does not exceed the limit that is determined by the formula is the energy, expressed in GJ, of the fuel combusted during the test by the jth boiler or heater; is the NOx emission intensity limit, expressed in g/GJ, that applies to the jth boiler or heater; is the energy, expressed in GJ, of the fuel combusted during the test by the kth boiler or heater; is the classification

    The text continues in the official source.

    Related guides, FAQ and contract templates