Beta
SOR-2013-24:en
SOR-2013-24:en — Heavy-duty Vehicle and Engine Greenhouse Gas Emission Regulations
Beta. Legal information, not legal advice. LEGALDIGM is not a law firm. Check the official source for the current text.
Analyze this law with AI1 (1) The following definitions apply in these Regulations.
Act means the Canadian Environmental Protection Act, 1999. (Loi)
adjusted loaded vehicle weight means the numerical average of the curb weight and the GVWR, and in the case of vehicles referred to in subsection 26(6) with an adjusted loaded vehicle weight of more than 6 350 kg (14,000 pounds), the value corresponding to the nearest 225 kg (500 pounds) increment. (poids ajusté du véhicule chargé)
aftertreatment device means a catalytic converter, particulate filter or any other system or component mounted downstream of the exhaust valve or exhaust port that is designed to decrease engine exhaust emissions before they are released into the environment. (dispositif de traitement postcombustion)
A to B testing means testing performed in pairs to allow comparison of a vehicle A to a vehicle B, an engine A to an engine B or equipment A to equipment B, as the case may be. (essais A à B)
automatic tire inflation system means a pneumatically or electronically activated system that is installed on a vehicle or a trailer to maintain tire pressure at a specified value. (dispositif automatique de gonflage des pneus)
auxiliary emission control device means any element of design that senses temperature, vehicle speed, engine RPM, transmission gear, manifold vacuum, or any other parameter for the purpose of activating, modulating, delaying or deactivating the operation of any part of an emission control system. (dispositif antipollution auxiliaire)
averaging set means, for the purpose of a company’s participation in the CO2 emission credit system set out in sections 34 to 47 or sections 47.1 to 47.5, as the case may be, any of the following groups of fleets of vehicles, engines or trailers:
(a) Class 2B and Class 3 heavy-duty vehicles and cab-complete vehicles, excluding those that are vocational vehicles or incomplete vocational vehicles;
(b) vocational vehicles that are light heavy-duty vehicles and incomplete vocational vehicles that are to become light heavy-duty vehicles;
(c) medium heavy-duty vehicles and heavy-duty incomplete vehicles that are to become medium heavy-duty vehicles, other than those that are of a type referred to in the table to subsection 26(1.2) and in respect of which the company has made the election referred to in that subsection;
(d) heavy heavy-duty vehicles and heavy-duty incomplete vehicles that are to become heavy heavy-duty vehicles, other than those that are of a type referred to in the table to subsection 26(1.2) and in respect of which the company has made the election referred to in that subsection;
(d.1) vocational vehicles that are all of the same type referred to in the table to subsection 26(1.2) and in respect of which the company has made the election referred to in that subsection;
(e) light heavy-duty engines and medium heavy-duty engines that are spark-ignition engines;
(f) light heavy-duty engines that are compression-ignition engines;
(g) medium heavy-duty engines that are compression-ignition engines;
(h) heavy heavy-duty engines;
(i) full-aero box van trailers that are short dry box van trailers and full-aero box van trailers that are short refrigerated box van trailers; or
(j) full-aero box van trailers that are long dry box van trailers and full-aero box van trailers that are long refrigerated box van trailers. (groupe de calcul de points)
basic vehicle frontal area means the area enclosed by the geometric projection of the basic vehicle — including tires but not mirrors or air deflectors — along the longitudinal axis of the vehicle onto a plane perpendicular to that axis. (surface frontale du véhicule de base)
box van trailer means a trailer — other than a tank trailer that is designed to transport liquids or gases — that has an enclosed cargo space that is permanently attached to the trailer chassis, has fixed sides and a fixed nose and roof. (remorque fourgon)
brake horsepower or BHP means a unit of brake power that is equal to 745.7 watts, expressed in horsepower. (BHP)
bus means a vocational vehicle that is designed to carry more than 15 passengers. (autobus)
cab-complete vehicle means a heavy-duty incomplete vehicle with either a completed occupant compartment that requires only the addition of a cargo-carrying surface, work-performing equipment or load-bearing component to perform its intended functions or with the back of the cab cut out for the intended installation of a structure that permits access from the driver’s area to the back of the vehicle. (véhicule à cabine complète)
calibration means the set of specifications and tolerances specific to a particular design, version or application of a component or assembly that describes its operation over its working range. (calibrages)
CFR means the Code of Federal Regulations of the United States, as amended from time to time. (CFR)
CH4 means methane. (CH4)
Class 2B means a class of heavy-duty vehicle that has a GVWR of more than 3 856 kg (8,500 pounds) but not more than 4 536 kg (10,000 pounds). (classe 2B)
Class 3 means a class of heavy-duty vehicle that has a GVWR of more than 4 536 kg (10,000 pounds) but not more than 6 350 kg (14,000 pounds). (classe 3)
Class 4 means a class of heavy-duty vehicle that has a GVWR of more than 6 350 kg (14,000 pounds) but not more than 7 257 kg (16,000 pounds). (classe 4)
Class 5 means a class of heavy-duty vehicle that has a GVWR of more than 7 257 kg (16,000 pounds) but not more than 8 845 kg (19,500 pounds). (classe 5)
Class 6 means a class of heavy-duty vehicle that has a GVWR of more than 8 845 kg (19,500 pounds) but not more than 11 793 kg (26,000 pounds). (classe 6)
Class 7 means a class of heavy-duty vehicle that has a GVWR of more than 11 793 kg (26,000 pounds) but not more than 14 969 kg (33,000 pounds). (classe 7)
Class 8 means a class of heavy-duty vehicle that has a GVWR of more than 14 969 kg (33,000 pounds). (classe 8)
coach bus means a bus that is designed for intercity passenger transport and that is not equipped with features to accommodate standing passengers. (autocar)
compression-ignition engine means an engine that operates as a reciprocating internal combustion engine, but does not include an engine that operates under characteristics significantly similar to the theoretical Otto combustion cycle or an engine that uses a spark plug or other sparking device. (moteur à allumage par compression)
concrete mixer means a vocational vehicle that is designed to mix and transport concrete in a revolving drum that is permanently mounted. (bétonnière)
CO2 means carbon dioxide. (CO2)
CO2 family certification level, in respect of a company’s heavy-duty engines, means the maximum CO2 emission level determined by the company for a fleet, which is greater than or equal to the maximum CO2 deteriorated emission level value calculated in accordance with subsection 32(1) for the engines that are included in the fleet. (niveau de certification de la famille applicable au CO2)
curb weight means the actual or manufacturer’s estimated weight of a heavy-duty vehicle in operational status with all standard equipment and includes the weight of fuel at nominal tank capacity and the weight of optional equipment. (masse en état de marche)
day cab means a tractor cab that is not a sleeper cab. (cabine de jour)
deteriorated emission level means the emission level that results from applying the applicable deterioration factor to the emission test results for a vehicle or engine. (niveau d’émissions détérioré)
deterioration factor means the factor used to account for the variation, if any, between the maximum emission level during the useful life of a vehicle or engine and the undeteriorated emission level measured at the point corresponding to a maximum of 6 437 km (4,000 miles) of operation in relation to a vehicle that has stabilized emissions and to a maximum of 125 hours of operation in relation to an engine that has stabilized emissions, determined in accordance with
(a) sections 1819(d)(5) and 1823(m) of Title 40, chapter I, subchapter C, part 86, subpart S, of the CFR, in the case of Class 2B and Class 3 heavy-duty vehicles and cab-complete vehicles, excluding those that are vocational vehicles or incomplete vocational vehicles;
(b) section 241(c) of Title 40, chapter I, subchapter U, part 1037, subpart C, of the CFR, in the case of vocational vehicles, incomplete vocational vehicles, tractors and incomplete tractors; and
(c) section 150(g) of Title 40, chapter I, subchapter U, part 1036, subpart B, of the CFR, and section 241(c) of Title 40, chapter I, subchapter U, part 1036, subpart C, of the CFR, in the case of heavy-duty engines. (facteur de détérioration)
dry box van trailer means a box van trailer other than a refrigerated box van trailer. (remorque fourgon non frigorifique)
electric vehicle means a heavy-duty vehicle, other than a fuel cell vehicle, that is not equipped with an internal combustion engine and is powered solely by an external source of electricity or solar power or a combination of electricity and solar power. (véhicule électrique)
element of design means, in respect of a vehicle, engine or trailer,
(a) any control system, including computer software, electronic control systems and computer logic;
(b) any control system calibrations;
(c) the results of systems interaction; or
(d) any hardware items. (élément de conception)
emergency vehicle means a vocational vehicle that is designed for use as an ambulance or fire truck. (véhicule d’urgence)
emission control system means any emission control device, auxiliary emission control device, engine modification and strategy, and other element of design used to reduce exhaust emissions from a vehicle or engine. (système antipollution)
engine configuration means a unique combination of heavy-duty engine hardware and calibration that has an effect on measured emissions within an engine family or engine subfamily, as the case may be. (configuration de moteur)
engine family, in respect of a company’s heavy-duty engines other than those referred to in section 25, means
(a) if they are covered by an EPA certificate, the grouping for which the EPA certificate was issued; or
(b) if they are not covered by an EPA certificate, the grouping determined in accordance with section 230 of Title 40, chapter I, subchapter U, part 1036, subpart C, of the CFR. (famille de moteurs)
engine subfamily, in respect of a company’s heavy-duty engines other than those referred to in section 25, means the grouping within an engine family having the same CO2 family certification level, determined in accordance with section 230 of Title 40, chapter I, subchapter U, part 1036, subpart C, of the CFR. (sous-famille de moteurs)
EPA means the United States Environmental Protection Agency. (EPA)
EPA certificate means a certificate of conformity with U.S. federal standards issued by the EPA. (certificat de l’EPA)
family emission limit means
(a) in the case of CO2 emissions,
(i) in respect of a company’s vocational vehicles and incomplete vocational vehicles, the maximum CO2 emission level determined by the company for a fleet or subfleet, which is greater than or equal to the maximum CO2 emission rate determined in accordance with subsection 26(2) for the vocational vehicles and incomplete vocational vehicles that are included in the fleet or subfleet,
(ii) in respect of a company’s tractors and incomplete tractors, the maximum CO2 emission level determined by the company for a fleet or subfleet, which is greater than or equal to the maximum CO2 emission rate determined in accordance with subsection 27(2) for the tractors and incomplete tractors that are included in the fleet or subfleet, and
(iii) in respect of a company’s full-aero box van trailers, the maximum CO2 emission level determined by the company for a subfleet, which is greater than or equal to the maximum CO2 emission rate determined in accordance with subsection 33.1(3) for the trailers that are included in the subfleet; and
(b) in the case of N2O or CH4 emissions,
(i) in respect of a company’s Class 2B and Class 3 heavy-duty vehicles and cab-complete vehicles — excluding those that are vocational vehicles or incomplete vocational vehicles — the maximum N2O or CH4 emission level determined by the company for a fleet or subfleet, which is greater than or equal to the maximum N2O or CH4 emission value determined in accordance with section 24 for the vehicles or vehicle configurations that are included in the fleet or subfleet, and
(ii) in respect of a company’s heavy-duty engines, the maximum N2O or CH4 emission level determined by the company for a fleet, which is greater than or equal to the maximum N2O or CH4 deteriorated emission level value calculated using the applicable emission value determined in accordance with subsection 29(2) for the engine configurations that are included in the fleet. (limite d’émissions de la famille)
FTP-based city test means the Federal Test Procedure set out in section 127 of Title 40, chapter I, subchapter C, part 86, subpart B, of the CFR, to comply with the FTP emission standards. (essai en ville)
fuel cell vehicle means a heavy-duty vehicle propelled solely by an electric motor, the energy for the motor being supplied by an electrochemical cell that produces electricity via the non-combustion reaction of a consumable fuel, typically hydrogen. (véhicule à pile à combustible)
full-aero, in respect of a box van trailer, means that the trailer does not have any of the following features:
(a) a belly box that occupies at least half of the length of both sides of the trailer between the centreline of the landing gear when it is extended and the leading edge of the front wheels;
(b) a drop deck;
(c) a side-mounted, pull-out platform;
(d) one or more steps for side-door access;
(e) a side lift gate;
(f) a rear hinged loading ramp;
(g) a rear mount for a forklift;
(h) a rear lift gate or, for the 2023 model year or an earlier model year, a roll-up rear door. (totalement aérodynamique)
GAWR means the gross axle weight rating that is specified by a manufacturer as the load-carrying capacity of a single axle system, as measured at the tire-ground interface. (PNBE)
GCWR means the gross combination weight rating that is specified by a manufacturer as the maximum design loaded weight of a vehicle and trailer. (PNBC)
GEM computer simulation model means the EPA’s GEM computer simulation model referred to in section 520 of Title 40, chapter I, subchapter U, part 1037, subpart F, of the CFR. (modèle de simulation informatique GEM)
GVWR means the gross vehicle weight rating that is specified by a manufacturer as the maximum design loaded weight of a vehicle. (PNBV)
heavy-duty completed vehicle
heavy-duty engine means an engine that is designed to be used for motive power in a vocational vehicle or a tractor. (moteur de véhicule lourd)
heavy-duty incomplete vehicle means a heavy-duty vehicle, an on-road vehicle with a curb weight of more than 2 722 kg (6,000 pounds) or an on-road vehicle with a basic vehicle frontal area in excess of 4.2 m2 (45 square feet) that consists of, at a minimum, a chassis, a powertrain and wheels in the state in which all of those components are to be part of the vehicle, but that requires further manufacturing operations to be completed. (véhicule lourd incomplet)
heavy-duty vehicle means an on-road vehicle that has a GVWR of more than 3 856 kg (8,500 pounds) but does not include a medium-duty passenger vehicle as defined in subsection 1(1) of the On-Road Vehicle and Engine Emission Regulations or a vehicle regulated under the Passenger Automobile and Light Truck Greenhouse Gas Emission Regulations. (véhicule lourd)
heavy-haul tractor means a tractor of the 2021 model year or a subsequent model year that has a GCWR of 63 503 kg (140,000 pounds) or more. (tracteur routier à chargement lourd)
heavy heavy-duty engine means a heavy-duty engine that has cylinder liners designed for multiple rebuilds and is designed to be used in Class 8 heavy-duty vehicles. (gros moteur de véhicule lourd)
heavy heavy-duty vehicle means
(a) for the 2020 model year and earlier model years, a Class 8 heavy-duty vehicle; and
(b) for the 2021 model year and subsequent model years,
(i) a Class 6, Class 7 or Class 8 vocational vehicle that is equipped with a heavy heavy-duty engine,
(ii) a Class 8 vocational vehicle that is an electric vehicle,
(iii) a Class 8 vocational vehicle that is a fuel cell vehicle,
(iv) a Class 8 vocational vehicle that is a hybrid vehicle, or
(v) a Class 8 tractor. (gros véhicule lourd)
HFET-based highway test means the Highway Fuel Economy Test Procedure referred to in subpart B of Title 40, chapter I, subchapter Q, part 600, of the CFR. (essai sur route)
high-roof, in relation to a tractor, means having a roof height of 376 cm (148 inches) or more. (toit élevé)
hybrid engine or hybrid powertrain means an engine or a powertrain that is equipped with energy storage features — other than a conventional battery system or conventional flywheel — such as supplemental electric batteries and hydraulic accumulators. (moteur hybride ou groupe motopropulseur hybride)
hybrid vehicle means a heavy-duty vehicle that is equipped with energy storage features — other than a conventional battery system or conventional flywheel — such as supplemental electric batteries and hydraulic accumulators, in addition to an internal combustion engine or other engine that uses fuel. (véhicule hybride)
incomplete tractor means a heavy-duty incomplete vehicle that is designed to become a tractor on completion of manufacturing operations. (tracteur routier incomplet)
incomplete vocational vehicle means a heavy-duty incomplete vehicle that is designed to become a vocational vehicle on completion of manufacturing operations. (véhicule spécialisé incomplet)
innovative technology means a greenhouse gas emission reduction technology for which the total emission reduction attributable to it cannot be measured by either GEM computer simulation modelling or the test procedures specified under these Regulations. (technologie innovatrice)
light heavy-duty engine means a heavy-duty engine that is designed to be used in Class 2B, Class 3, Class 4 or Class 5 heavy-duty vehicles. (petit moteur de véhicule lourd)
light heavy-duty vehicle means a Class 2B, Class 3, Class 4 or Class 5 heavy-duty vehicle. (petit véhicule lourd)
long, in respect of a trailer, means more than 15.24 metres (50 feet) in length. (longue)
low-roof, in relation to a tractor, means having a roof height of 305 cm (120 inches) or less. (toit bas)
medium heavy-duty engine means a heavy-duty engine that is designed to be used in Class 6 and Class 7 heavy-duty vehicles. (moteur moyen de véhicule lourd)
medium heavy-duty vehicle means
(a) for the 2020 model year and earlier model years, a Class 6 or Class 7 heavy-duty vehicle; and
(b) for the 2021 model year and subsequent model years,
(i) a Class 6, Class 7 or Class 8 vocational vehicle that is not a hybrid vehicle and is equipped with an engine other than a heavy heavy-duty engine,
(ii) a Class 6 or Class 7 vocational vehicle that is an electric vehicle,
(iii) a Class 6 or Class 7 vocational vehicle that is a fuel cell vehicle,
(iv) a Class 6 or Class 7 vocational vehicle that is a hybrid vehicle, or
(v) a Class 7 tractor. (véhicule mi-lourd)
mid-roof, in relation to a tractor, means having a roof height of more than 305 cm (120 inches) but less than 376 cm (148 inches). (toit moyen)
mixed-use vocational vehicle means a vocational vehicle that
(a) is designed to operate at low speeds that are unsuitable for normal highway operation, has affixed components that are designed to operate in an off-road environment or has both of those characteristics; or
(b) has one or more of the following characteristics:
(i) it has an axle that has a GAWR of 13 154 kg (29,000 pounds) or more,
(ii) it cannot attain a speed of more than 53 km/h (33 miles per hour) over 3.2 km (2 miles),
(iii) it cannot attain a speed of more than 72 km/h (45 miles per hour) over 3.2 km (2 miles), it has an unloaded vehicle weight that is not less than 95% of its GVWR and it cannot carry occupants other than the driver and operating crew,
(iv) it cannot attain a speed of more than 87 km/h (54 miles per hour)
(A) due to parameters that are not adjustable parameters as defined in subsection 15(1), or
(B) without the engine with which it is equipped being at 95% or more of its maximum test speed in the highest available gear ratio. (véhicule spécialisé à usages divers)
model year means the year, determined in accordance with section 4, that is used by a manufacturer to designate a model of vehicle, engine or trailer. (année de modèle)
motor home means a vocational vehicle that is designed to provide temporary residential accommodations and that is equipped with at least four of the following features:
(a) a cooking appliance;
(b) a refrigerator;
(c) a self-contained toilet;
(d) a heating or air-conditioning system;
(e) a potable water supply system, including a faucet and a sink;
(f) a 110-125 volt alternating current (VAC) electrical supply system or propane supply system. (autocaravane)
multi-purpose vocational vehicle means a vocational vehicle that is neither a regional vocational vehicle nor an urban vocational vehicle. (véhicule spécialisé à usages multiples)
nominal tank capacity means the fuel tank’s volume that is specified by a manufacturer to the nearest three eighths of a litre (one tenth of a U.S. gallon). (capacité nominale du réservoir à carburant)
non-aero box van trailer means
(a) a box van trailer that is at least 10.67 metres (35 feet) in length and that has
(i) at least one of the following rear features:
(A) a hinged loading ramp,
(B) a lift gate,
(C) a mount for a forklift,
(D) for the 2023 model year or an earlier model year, a roll-up door, and
(ii) at least one of the following side features:
(A) a belly box that occupies at least half of the length of both sides of the trailer between the centreline of the landing gear when it is extended and the leading edge of the front wheels,
(B) a drop deck,
(C) a mounted, pull-out platform,
(D) one or more steps for side-door access,
(E) a lift gate; or
(b) a short refrigerated box van trailer that is less than 10.67 metres (35 feet) in length and has at least one of the side features listed in clauses (a)(ii)(A) to (E). (remorque fourgon non aérodynamique)
non-box trailer means a tank trailer that is designed to transport liquids or gases, a trailer that is designed to carry a temporarily mounted shipping container or a trailer that is designed to accommodate side-loading cargo onto a single, continuous load-bearing surface that runs from the rear of the trailer to at least the trailer’s kingpin and that may have curtains, straps or other devices to restrain or protect the cargo during transport, including side walls that do not completely enclose the cargo space. (remorque sans fourgon)
N2O means nitrous oxide. (N2O)
on-road vehicle means a self-propelled vehicle that is designed for or capable of transporting persons, property, material or permanently or temporarily affixed apparatus on a highway, but does not mean a vehicle that
(a) cannot exceed a speed of 40 km/h (25 miles per hour) on a level paved surface;
(b) lacks features customarily associated with safe and practical highway use such as a reverse gear, a differential or safety features that are required by federal or provincial laws;
(c) exhibits features that render its use on a highway unsafe, impractical or highly unlikely, such as tracked road contact means or inordinate size; or
(d) is a military vehicle that is designed for use in combat or combat support. (véhicule routier)
partial-aero, in respect of a box van trailer other than a non-aero box van trailer, means that the trailer
(a) has at least one of the following side features:
(i) a belly box that occupies at least half of the length of both sides of the trailer between the centreline of the landing gear when it is extended and the leading edge of the front wheels,
(ii) a drop deck,
(iii) a mounted, pull-out platform,
(iv) one or more steps for side-door access,
(v) a lift gate; or
(b) in the case of a long dry box van trailer or a long refrigerated box van trailer, has at least one of the following rear features:
(i) a hinged loading ramp,
(ii) a lift gate,
(iii) a mount for a forklift,
(iv) for the 2023 model year or an earlier model year, a roll-up door. (partiellement aérodynamique)
plug-in hybrid vehicle means a hybrid vehicle that has an energy storage system that can be recharged from an electric source that is not on board the vehicle. (véhicule hybride rechargeable)
power take-off means a secondary engine shaft or other system of a vehicle that provides substantial auxiliary power for purposes unrelated to vehicle propulsion or the functioning of customary vehicle accessories such as air conditioning, power steering and basic accessories. (prise de mouvement)
refrigerated box van trailer means a box van trailer that has a self-contained heating, ventilation or air-conditioning system. (remorque fourgon frigorifique)
regional vocational vehicle means a vocational vehicle that has any of the characteristics of a vehicle to which the regional duty cycle is applicable under section 510 of Title 40, chapter I, subchapter U, part 1037, subpart F, of the CFR. (véhicule spécialisé régional)
short, in respect of a trailer, means not more than 15.24 metres (50 feet) in length. (courte)
sleeper cab means a tractor cab that has a compartment located behind the driver’s seat that is designed to be used as a sleeping accommodation and that is accessible either from the driver’s compartment or from outside the vehicle. (cabine couchette)
spark-ignition engine means an engine that operates under characteristics significantly similar to the theoretical Otto combustion cycle and uses a spark plug or other sparking device. (moteur à allumage commandé)
static loaded radius means the distance between the level surface where the vehicle is located and the axle centre measured at curb weight when the vehicle is stationary, with the wheels parallel to the vehicle’s longitudinal centre line and the tires inflated to the manufacturer’s recommended cold tire inflation pressure. (rayon sous charge statique)
steady state duty cycle means the test cycle that is referred to in section 1362 of Title 40, chapter I, subchapter C, part 86, subpart N, of the CFR. (cycle de service permanent)
test group, in respect of a company’s Class 2B and Class 3 heavy-duty vehicles, excluding those that are vocational vehicles or incomplete vocational vehicles, and the company’s engines referred to in section 25, means
(a) if they are covered by an EPA certificate, the grouping for which the EPA certificate was issued; and
(b) if they are not covered by an EPA certificate, the grouping determined in accordance with section 1827 of Title 40, chapter I, subchapter C, part 86, subpart S, of the CFR. (groupe d’essai)
test weight means the vehicle weight that is used or represented during testing. (masse à l’essai)
tire pressure monitoring system means a system that is installed on a vehicle or a trailer to monitor the air pressure in each tire and alert the driver when the tire pressure falls below a specified value. (système de surveillance de la pression des pneus)
tire rolling resistance level means the rolling resistance of a tire configuration, expressed in kilograms per tonne. (niveau de résistance au roulement du pneu)
tractor means a Class 7 or Class 8 heavy-duty vehicle that is manufactured primarily for pulling a trailer but not for carrying cargo other than cargo in the trailer. (tracteur routier)
trailer means equipment with wheels that is designed to carry cargo and be pulled by a tractor when coupled to the tractor’s fifth wheel, excluding equipment that
(a) is less than 10.67 metres (35 feet) in length and has three axles;
(b) has four or more axles;
(c) has adjacent axles whose centrelines are at least 305 cm (120 inches) apart and, if the distance between the axles is adjustable, cannot be set closer together;
(d) is intended to be used as a temporary or permanent residence or as an office or other work space; or
(e) is designed for use in military combat or combat support. (remorque)
trailer family, in respect of a company’s trailers, means
(a) if they are covered by an EPA certificate, the grouping for which the EPA certificate was issued; or
(b) if they are not covered by an EPA certificate, the trailers within a grouping referred to in section 230 of Title 40, chapter I, subchapter U, part 1037, subpart C, of the CFR, except that a reference to “vehicle” in sections 230(b) and (d)(3) of Title 40, chapter I, subchapter U, part 1037, subpart C, of the CFR must be read as a reference to “trailer”. (famille de remorques)
transient duty cycle means the test cycle that is referred to in section 1333 of Title 40, chapter I, subchapter C, part 86, subpart N, of the CFR. (cycle de service transitoire)
urban vocational vehicle means a vocational vehicle that has any of the characteristics of a vehicle to which the urban duty cycle is applicable under section 510 of Title 40, chapter I, subchapter U, part 1037, subpart F, of the CFR. (véhicule spécialisé urbain)
vehicle configuration means, in respect of Class 2B and Class 3 heavy-duty vehicles and cab-complete vehicles, a configuration as defined in section 1819(d)(12)(i) of Title 40, chapter I, subchapter C, part 86, subpart S, of the CFR. (configuration de véhicule)
vehicle family, in respect of a company’s tractors or vocational vehicles, means
(a) if they are covered by an EPA certificate, the grouping for which the EPA certificate was issued; or
(b) if they are not covered by an EPA certificate, the grouping determined in accordance with section 230 of Title 40, chapter I, subchapter U, part 1037, subpart C, of the CFR. (famille de véhicules)
vehicle service class means any one of the following groups:
(a) light heavy-duty vehicles;
(b) medium heavy-duty vehicles; or
(c) heavy heavy-duty vehicles. (classe de service)
vehicle subconfiguration means, within a vehicle configuration of Class 2B and Class 3 heavy-duty vehicles and cab-complete vehicles, a unique combination of equivalent test weight and road load horsepower, and any other operational characteristics or parameters that may significantly affect CO2 emissions within the vehicle configuration. (sous-configuration de véhicule)
vocational tractor means any of the following tractors that are not designed primarily to operate at high and constant speeds such as on highways, or that would not benefit from efficiency improvements designed for line-haul tractors:
(a) a low-roof tractor that is designed for local pickup and delivery;
(b) a tractor that is designed for both on-road and off-road use, such as a tractor with a reinforced frame and increased ground clearance; or
(c) a tractor of the 2020 model year or an earlier model year that has a GCWR of 54 431 kg (120,000 pounds) or more. (tracteur routier spécialisé)
vocational vehicle means any of the following:
(a) a Class 4, Class 5 or Class 6 heavy-duty vehicle;
(b) a Class 7 or Class 8 heavy-duty vehicle that is not a tractor;
(c) a vocational tractor;
(d) a heavy-duty incomplete vehicle that is not a cab-complete vehicle and is equipped with an engine conforming to the alternative standard referred to in section 25; or
(e) a Class 2B or Class 3 heavy-duty vehicle that is not subject to section 1819 of Title 40, chapter I, subchapter C, part 86, subpart S, of the CFR. (véhicule spécialisé)
(2) Standards that are incorporated by reference in these Regulations from the CFR are those expressly set out in the CFR and must be read as excluding
(a) references to the EPA or the Administrator of the EPA exercising discretion in any way;
(b) references to the Secretary of Transportation exercising discretion in any way;
(c) alternative standards related to fleet averages, other averages, emission credits, small volume manufacturers or financial hardship; and
(d) standards or evidence of conformity of any authority other than the EPA.
(3) For the purposes of subsection (2), a reference in the CFR to “carbon-related exhaust emissions” and “CREE” must be read as “CO2 emissions”.
(4) The calculations and measurements in these Regulations must be rounded in accordance with section 20(e) of Title 40, chapter I, subchapter U, part 1065, subpart A, of the CFR, unless otherwise provided in
(a) these Regulations;
(b) part 1037 of Title 40, chapter I, subchapter U, of the CFR, for the applicable standards and test procedures in the case of trailers and heavy-duty vehicles other than those referred to in paragraph (b.1);
(b.1) section 1819 of Title 40, chapter I, subchapter C, part 86, subpart S, of the CFR, for the applicable standards and test procedures in the case of Class 2B and Class 3 heavy-duty vehicles and cab-complete vehicles, excluding those that are vocational vehicles or incomplete vocational vehicles; or
(c) part 1036 of Title 40, chapter I, subchapter U, of the CFR, for the applicable standards and test procedures in the case of heavy-duty engines.
(5) Unless otherwise provided in these Regulations, useful life refers to the period of time or use in respect of which an emission standard applies to, as the case may be,
(a) Class 2B and Class 3 heavy-duty vehicles and cab-complete vehicles — excluding those that are vocational vehicles or incomplete vocational vehicles — namely,
(i) for the 2020 model year and earlier model years, 11 years or 193 121 km (120,000 miles), whichever occurs first, and
(ii) for the 2021 model year and subsequent model years, 15 years or 241 401 km (150,000 miles), whichever occurs first;
(b) vocational vehicles that are light heavy-duty vehicles and incomplete vocational vehicles that are to become light heavy-duty vehicles, namely,
(i) for the 2020 model year and earlier model years, 10 years or 177 027 km (110,000 miles), whichever occurs first, and
(ii) for the 2021 model year and subsequent model years, 15 years or 241 401 km (150,000 miles), whichever occurs first;
(c) vocational vehicles that are medium heavy-duty vehicles, incomplete vocational vehicles that are to become medium heavy-duty vehicles, Class 7 tractors and incomplete tractors that are to become Class 7 tractors, namely, 10 years or 297 728 km (185,000 miles), whichever occurs first;
(d) vocational vehicles that are heavy heavy-duty vehicles, incomplete vocational vehicles that are to become heavy heavy-duty vehicles, Class 8 tractors and incomplete tractors that are to become Class 8 tractors, namely, 10 years or 700 064 km (435,000 miles), whichever occurs first;
(e) heavy-duty engines, namely,
(i) in the case of spark-ignition engines and of light heavy-duty engines that are compression-ignition engines of the 2021 model year or a subsequent model year, 15 years or 241 401 km (150,000 miles), whichever occurs first, and
(ii) in any other case, the same useful life as that which is set out for the type of engine in question in section 2 of Title 40, chapter I, subchapter C, part 86, subpart A, of the CFR for emissions of oxides of nitrogen (NOX), hydrocarbon (HC), particulate matter (PM) and carbon monoxide (CO); and
(f) trailers, namely, 10 years.
(6) Subject to subsections (7) and (8), “roof height” refers to the maximum height of a tractor, rounded to the nearest inch, excluding small accessories such as exhaust pipes and antennas, but including large accessories such as roof fairings, and measured with tires inflated to the manufacturer’s recommended cold tire inflation pressure and without occupants or cargo onboard.
(7) The roof height of a tractor must be measured with a static loaded radius equal to the arithmetic mean of the largest and smallest static loaded radius of the tires that are recommended for the tractor by the manufacturer.
(8) In the case of a tractor equipped with an adjustable roof fairing, the roof height must be measured with the fairing in its lowest setting.
(8.1) The length of a trailer corresponds to
(a) the outer dimensions of its load-carrying structure, excluding any aerodynamic devices and any heating, ventilating or air-conditioning systems; and
(b) in the case of a B-train trailer, the outer dimensions of its load-carrying structure, excluding its rear fifth-wheel coupling section, any aerodynamic devices and any heating, ventilating or air-conditioning systems.
(8.2) The number of axles on a vehicle or trailer includes any axles that can be used to carry the loaded or unloaded weight of the vehicle or the trailer while in motion, including lift axles.
(9) A family emission limit and a CO2 family certification level must be expressed to the same number of decimal places as the emission standard they replace.
(10) For the purposes of these Regulations, a spark-ignition engine of the 2020 model year or an earlier model year that is regulated as a diesel engine under part 86 of Title 40, chapter I, subchapter C, of the CFR must conform to the standards, test procedures and calculation methods applicable to a compression-ignition engine of the same model year.
(11) For the purposes of these Regulations, a compression-ignition engine of the 2020 model year or an earlier model year that is regulated as an Otto-cycle engine under part 86 of Title 40, chapter I, subchapter C, of the CFR must conform to the standards, test procedures and calculation methods applicable to a spark-ignition engine of the same model year.
(12) For the purposes of these Regulations, the following engines must conform to the standards, test procedures and calculation methods applicable to a compression-ignition engine of the same model year:
(a) a gas turbine heavy-duty engine; and
(b) a heavy-duty engine that is not a spark-ignition engine or compression-ignition engine.
1.1 For the purposes of these Regulations, a vehicle, engine or trailer of a given model year that is sold in Canada is considered to be sold concurrently in Canada and in the United States if a vehicle, engine or trailer of that model year that belongs to the same test group, vehicle family, engine family or trailer family is offered for sale in the United States during the 365 days preceding
(a) in the case of a vehicle, engine or trailer that is imported into Canada, the day on which it is imported; and
(b) in the case of a vehicle, engine or trailer that is manufactured in Canada,
(i) the day on which the national emissions mark is applied to the vehicle, engine or trailer, if known, or
(ii) if the day referred to in subparagraph (i) is not known, the day on which the main assembly of the vehicle or the manufacture of the engine or the trailer, as the case may be, is completed.
2 These Regulations apply to the vehicles, engines and equipment that are prescribed by subsections 5(1) to (3).
4 (1) Subject to subsection (3), a year that is used by a manufacturer as a model year must,
(a) if the period of production of a model of heavy-duty vehicle, heavy-duty engine or trailer does not include January 1 of a calendar year, correspond to the calendar year during which the period of production falls; and
(b) if the period of production of a model of heavy-duty vehicle, heavy-duty engine or trailer includes January 1 of a calendar year, correspond to that calendar year.
(2) The period of production of a model of heavy-duty vehicle, heavy-duty engine or trailer must include only one January 1.
(3) For vocational vehicles, incomplete vocational vehicles, tractors and incomplete tractors whose main assembly is completed on or after January 1, 2021, the vehicle’s model year is the calendar year corresponding to the calendar year during which its main assembly is completed. However, a company may choose to designate the vehicle’s model year as being
(a) the model year that corresponds to the calendar year after the calendar year during which the vehicle’s main assembly is completed; or
(b) the model year that corresponds to the calendar year before the calendar year during which the vehicle’s main assembly is completed if,
(i) in the case of a vehicle whose engine is installed in the United States, the engine’s model year is also from an earlier year in accordance with section 601(a)(2) of Title 40, chapter I, subchapter U, part 1037, subpart G, of the CFR and, if the engine is installed after March 31 of the calendar year during which the vehicle’s main assembly is completed, the company has obtained prior approval from the EPA, and
(ii) in the case of a vehicle whose engine is installed in Canada,
(A) the engine’s model year is also from an earlier year and the standards applicable under these Regulations to engines of that earlier model year are the same as those applicable to engines of a model year that corresponds to the calendar year during which the vehicle’s main assembly is completed, or
(B) the engine’s model year is the model year that corresponds to the calendar year before the calendar year during which the vehicle’s main assembly is completed and the engine is installed before March 31 of the calendar year during which the vehicle’s main assembly is completed.
5 (1) The following classes of vehicles are prescribed for the purposes of the definition vehicle in section 149 of the Act:
(a) Class 2B and Class 3 heavy-duty vehicles;
(b) vocational vehicles;
(c) tractors; and
(d) heavy-duty incomplete vehicles.
(2) Heavy-duty engines are prescribed for the purposes of the definition engine in section 149 of the Act.
(2.1) Box van trailers and non-box trailers are prescribed for the purposes of the definition equipment in section 149 of the Act.
(3) The prescribed classes of vehicles, engines and equipment set out in subsections (1), (2) and (2.1), respectively, do not include heavy-duty vehicles, heavy-duty engines or trailers that are to be exported and that are accompanied by written evidence establishing that they will not be sold for use or used in Canada.
(4) For the purposes of section 152 of the Act, the prescribed vehicles are the vehicles referred to in subsection (1) for which the main assembly is completed in Canada, other than a vehicle that will be used in Canada solely for purposes of exhibition, demonstration, evaluation or testing.
(5) For the purposes of section 152 of the Act, the prescribed engines are the engines referred to in subsection (2) that are manufactured in Canada, other than
(a) an engine that will be used in Canada solely for purposes of exhibition, demonstration, evaluation or testing;
(b) an engine that is to be installed in a heavy-duty vehicle before sale to the vehicle’s first retail purchaser; and
(c) an engine that is to be installed as a replacement engine in a heavy-duty vehicle that has a national emissions mark applied to it, if the replacement engine is
(i) of the same model year as the original engine, and
(ii) identical to or better than the original engine with respect to emissions.
(6) For the purposes of section 152 of the Act, the prescribed equipment is box van trailers and non-box trailers that are manufactured in Canada, other than trailers that will be used in Canada solely for purposes of exhibition, demonstration, evaluation or testing.
6 (1) A company that intends to apply a national emissions mark to a vehicle, engine or trailer must apply to the Minister for authorization.
(1.1) The application must be signed by a person who is authorized to act on behalf of the company and must include
(a) the name and street address of the company’s head office and, if different, its mailing address;
(b) the classes of vehicles, engines or trailers for which the authorization is requested;
(c) the street address of the location at which the national emissions mark will be applied to the vehicles, engines or trailers;
(d) the street address where the records referred to in section 59 will be maintained; and
(e) information demonstrating that the company is capable of verifying compliance with the standards set out in these Regulations.
(2) Subsection (1) does not apply to a company that, on the day on which these Regulations come into force, is authorized to apply the national emissions mark to a vehicle or engine under the On-Road Vehicle and Engine Emission Regulations.
7 (1) The national emissions mark is the mark set out in the schedule.
(2) The national emissions mark must be at least 7 mm in height and 10 mm in width.
(3) Subject to subsection 11(2), the national emissions mark must be displayed
(a) on or immediately beside the U.S. emission control information label or U.S. engine information label referred to in paragraph 53(d);
(b) on or immediately beside the compliance label applied in accordance with the Motor Vehicle Safety Regulations; or
(c) on or immediately beside the compliance label referred to in section 8, 9 or 9.1, as the case may be.
(4) The national emissions mark must be displayed on a label that
(a) is permanently applied to the vehicle, engine or trailer;
(b) is resistant to or protected against any weather condition; and
(c) bears inscriptions that are legible and indelible and that are indented, embossed or in a colour that contrasts with the background of the label.
(5) Subject to subsection (6), a company that has been authorized to apply the national emissions mark must display the authorization number assigned by the Minister in figures that are at least 2 mm in height, immediately below or to the right of the national emissions mark.
(6) A company is not required to display its authorization number on a vehicle or trailer if
(a) the company is authorized by the Minister of Transport to apply the national safety mark in accordance with the Motor Vehicle Safety Act;
(b) the company applies both the national emissions mark and the national safety mark to the vehicle or the trailer; and
(c) the national emissions mark is displayed on the same label as the national safety mark.
8 (1) Heavy-duty engines and the engines referred to in section 25 that are imported or manufactured in Canada — other than EPA-certified engines that bear the label referred to in subparagraph 53(d)(ii) — must bear a compliance label that sets out the following information:
(a) subject to subsection (2), the statement “THIS ENGINE CONFORMS TO ALL APPLICABLE STANDARDS PRESCRIBED BY THE CANADIAN REGULATIONS ENTITLED Heavy-duty Vehicle and Engine Greenhouse Gas Emission Regulations IN EFFECT FOR MODEL YEAR [insert model year] / CE MOTEUR EST CONFORME AUX NORMES QUI LUI SONT APPLICABLES PRÉVUES AU RÈGLEMENT CANADIEN INTITULÉ Règlement sur les émissions de gaz à effet de serre des véhicules lourds et de leurs moteurs EN VIGUEUR POUR L’ANNÉE DE MODÈLE [inscrire l’année de modèle]”;
(b) the name of the engine’s manufacturer;
(c) the engine’s model year if a national emissions mark is applied to the engine;
(d) subject to subsection (3), the engine’s date of manufacture;
(e) subject to subsection (3), the engine’s unique identification number;
(f) the model designations;
(g) the engine displacement;
(h) the identification of the emission control system;
(i) the engine family’s or test group’s identification code, as the case may be;
(j) the limits on the types of use for the engine to ensure that the emission standards set out in these Regulations are complied with;
(k) the engine specifications and adjustments recommended by the engine’s manufacturer;
(l) in the case of a spark-ignition engine, the valve lash, idle speed, ignition timing and idle air-fuel mixture setting procedure and value;
(m) in the case of a compression-ignition engine, the engine power specified by the manufacturer and expressed in HP, the RPM at the specified horsepower, the fuel rate at the specified horsepower expressed in mm3 per stroke, the valve lash, idle speed and initial injection timing; and
(n) in the case of a heavy-duty engine that is exempted under subsection 17(1.1), the engine’s model year and a statement, in both official languages, that the engine is exempted under that subsection.
(2) Paragraph (1)(a) does not apply when a national emissions mark is applied to the engine.
(3) The engine’s date of manufacture referred to in paragraph (1)(d) and unique identification number referred to in paragraph (1)(e) may, instead of being set out on the label, be permanently affixed, engraved or stamped on the engine.
(4) In the case of spark-ignition engines referred to in section 25, the label referred to in subsection (1) must also set out one of the following statements, whichever applies:
(a) a statement in both official languages that the engine conforms to the alternative greenhouse gas emission standards for engines of Class 2B and Class 3 heavy-duty vehicles; or
(b) the statement referred to in section 1819(k)(8)(v) of Title 40, chapter I, subchapter C, part 86, subpart S, of the CFR.
(5) In the case of compression-ignition engines referred to in subsection 31(1), the label referred to in subsection (1) must also set out one of the following statements, whichever applies:
(a) a statement in both official languages that the engine conforms to the alternative CO2 emission standard based on model year 2011 compression-ignition engines; or
(b) the statement referred to in section 620(d) of Title 40, chapter I, subchapter U, part 1036, subpart G, of the CFR.
9 (1) Heavy-duty vehicles that are imported or manufactured in Canada — other than EPA-certified heavy-duty vehicles that bear the label referred to in subparagraph 53(d)(i) — must bear a compliance label that sets out the following information:
(a) subject to subsection (2), the statement “THIS VEHICLE CONFORMS TO ALL APPLICABLE STANDARDS PRESCRIBED BY THE CANADIAN REGULATIONS ENTITLED Heavy-duty Vehicle and Engine Greenhouse Gas Emission Regulations IN EFFECT FOR MODEL YEAR [insert model year] / CE VÉHICULE EST CONFORME AUX NORMES QUI LUI SONT APPLICABLES PRÉVUES AU RÈGLEMENT CANADIEN INTITULÉ Règlement sur les émissions de gaz à effet de serre des véhicules lourds et de leurs moteurs EN VIGUEUR POUR L’ANNÉE DE MODÈLE [inscrire l’année de modèle]”;
(b) the name of the vehicle’s manufacturer;
(c) the vehicle’s model year if a national emissions mark is applied to the vehicle;
(d) subject to subsection (3), the date on which the vehicle’s main assembly is completed;
(e) the type of vehicle, in both official languages, referred to in paragraph 18(3)(a);
(f) the vehicle family’s or test group’s identification code, as the case may be;
(g) except in the case of a vocational vehicle, incomplete vocational vehicle, tractor or incomplete tractor of the 2021 model year or a subsequent model year, the identification of the vehicle’s emission control system;
(h) in the case of a vocational vehicle or incomplete vocational vehicle referred to in subsection 26(3), the vehicle’s model year and a statement, in both official languages, that the vehicle is exempted under that subsection;
(i) in the case of a vocational tractor or vocational tractor that is an incomplete tractor, a statement, in both official languages, that the vehicle is a vocational tractor;
(j) in the case of a vocational vehicle, incomplete vocational vehicle, tractor or incomplete tractor that is exempted under subsection 17(1), the vehicle’s model year and a statement, in both official languages, that the vehicle is exempted under that subsection;
(k) in the case of a Class 2B or Class 3 heavy-duty vehicle or cab-complete vehicle — excluding those that are vocational vehicles or incomplete vocational vehicles — the engine displacement and the CO2 emission value determined by variable A in accordance with subsection 23(1) for that vehicle configuration and if applicable, the N2O and CH4 family emission limits;
(l) in the case of a vocational vehicle, incomplete vocational vehicle, tractor or incomplete tractor referred to in subsection 12.2(2), a statement, in both official languages, that the vehicle is equipped with an engine that meets the conditions set out in that subsection 12.2(2) and conforms to the standards referred to in subsection 12.2(3);
(m) in the case of a hybrid vehicle referred to in subsection 12.2(4), a statement, in both official languages, that the vehicle is equipped with an engine that conforms to the applicable alternative standards referred to in that subsection; and
(n) in the case of a vocational vehicle or incomplete vocational vehicle in respect of which the company makes an election referred to in subsection 26(1.2), a statement to that effect, in both official languages, and the type of vocational vehicle or incomplete vocational vehicle referred to in column 1 of the table to that subsection.
(2) Paragraph (1)(a) does not apply if a national emissions mark is applied to the vehicle or if the information referred to in paragraph (1)(h) or (j) is set out on the label.
(3) The date referred to in paragraph (1)(d) may, instead of being set out on the label, be permanently affixed, engraved or stamped on the vehicle.
9.1 (1) Every box van trailer and non-box trailer that is imported or manufactured in Canada — other than EPA-certified trailers that bear the U.S. emission control information label referred to in subparagraph 53(d)(i) — must bear a compliance label that sets out the following information:
(a) subject to subsection (2), the statement “THIS TRAILER CONFORMS TO ALL APPLICABLE STANDARDS PRESCRIBED BY THE CANADIAN REGULATIONS ENTITLED Heavy-duty Vehicle and Engine Greenhouse Gas Emission Regulations IN EFFECT FOR MODEL YEAR [insert model year] / CETTE REMORQUE EST CONFORME AUX NORMES QUI LUI SONT APPLICABLES PRÉVUES AU RÈGLEMENT CANADIEN INTITULÉ Règlement sur les émissions de gaz à effet de serre des véhicules lourds et de leurs moteurs EN VIGUEUR POUR L’ANNÉE DE MODÈLE [inscrire l’année de modèle]”;
(b) the name of the trailer’s manufacturer;
(c) the trailer’s model year if a national emissions mark is applied to it;
(d) subject to subsection (3), the trailer’s date of manufacture;
(e) the type of trailer, in both official languages;
(f) the trailer family’s identification code; and
(g) in the case of a trailer that is exempted under section 17.1 or 17.2, a statement in both official languages that the trailer is exempted under that section and, if not already indicated under paragraph (c), the trailer’s model year.
(2) Paragraph (1)(a) does not apply if a national emissions mark is applied to the trailer.
(3) The trailer’s date of manufacture may, instead of being set out on the label, be permanently affixed, engraved or stamped on the trailer.
10 Any label that is required by these Regulations, other than a U.S. emission control information label or U.S. engine information label referred to in paragraph 53(d), must
(a) be applied to a conspicuous and readily accessible location;
(b) be permanently applied to the vehicle or the trailer and, in the case of an engine, be permanently applied to an engine part that is necessary for normal engine operation and does not normally require replacement during the engine’s useful life;
(c) be resistant to or protected against any weather condition;
(d) have lettering that is
(i) clear and indelible,
(ii) indented, embossed or in a colour that contrasts with the background colour of the label, and
(iii) in block capitals and numerals that are not less than 2 mm in height; and
(e) have units that are identified by the appropriate name or symbol.
11 (1) If a company alters a heavy-duty vehicle or heavy-duty incomplete vehicle that was in conformity with these Regulations in such a manner that its stated type of vehicle referred to in paragraph 18(3)(a) is no longer accurate, or if the company alters the emission control system, alters an engine configuration in a way that might affect emissions or replaces any of the components of the vehicle that might alter the value of a parameter used in the GEM computer simulation model, the company must
(a) ensure that the U.S. emission control information label referred to in subparagraph 53(d)(i), the compliance label referred to in section 9 and the national emissions mark, as the case may be, remain applied to the altered vehicle;
(b) ensure that the vehicle, once altered, conforms to all applicable standards;
(c) apply to the altered vehicle an additional label that sets out the following information:
(i) the words “THIS VEHICLE WAS ALTERED BY / CE VÉHICULE A ÉTÉ MODIFIÉ PAR”, followed by the name of the company that altered the vehicle,
(ii) the month and year during which the alteration was made to the vehicle,
(iii) the national emissions mark, and
(iv) the type of vehicle referred to in paragraph 18(3)(a), if it differs from the type set out on the compliance label referred to in section 9 or if the regulatory subcategory that is set out on the U.S. emission control information label referred to in subparagraph 53(d)(i) is changed, as the case may be; and
(d) obtain and produce the evidence of conformity referred to in section 54 for the altered vehicle in a form and manner that is satisfactory to the Minister before the vehicle leaves its possession or control.
(2) The national emissions mark referred to in subparagraph (1)(c)(iii) must be displayed on a label applied to the vehicle immediately beside any previously applied label on which the national emissions mark appears or immediately beside the U.S. emission control information label referred to in subparagraph 53(d)(i).
(3) A company that alters a vehicle in accordance with this section must not participate in the CO2 emission credit system set out in sections 34 to 47 with respect to that altered vehicle.
12 (1) Subject to subsection (2), these Regulations apply to vehicles for which the main assembly is completed on or after January 1, 2014.
(2) A company may elect to comply with these Regulations with respect to its heavy-duty vehicles of the 2014 model year for which the main assembly is completed before January 1, 2014 for the purpose of participation in the CO2 emission credit system set out in sections 34 to 47.
12.1 These Regulations apply to trailers whose manufacture is completed on or after January 1, 2020.
12.2 (1) Subject to subsections (2) and (4), every vocational vehicle, incomplete vocational vehicle, tractor and incomplete tractor whose main assembly is completed after the coming into force of this section must be equipped with a heavy-duty engine that conforms to the following standards:
(a) the standards set out in the On-Road Vehicle and Engine Emission Regulations that are applicable to heavy-duty engines as defined in subsection 1(1) of those Regulations that are of the following model year:
(i) in the case of a vehicle whose main assembly is completed before January 1, 2021, the model year of the engine with which the vocational vehicle, incomplete vocational vehicle, tractor or incomplete tractor is equipped, and
(ii) in the case of a vehicle whose main assembly is completed on or after January 1, 2021, the model year that corresponds to
(A) the calendar year during which the main assembly of the vocational vehicle, incomplete vocational vehicle, tractor or incomplete tractor in which the engine is installed is completed,
(B) the calendar year after the calendar year during which the main assembly of the vocational vehicle, incomplete vocational vehicle, tractor or incomplete tractor in which the engine is installed is completed, or
(C) if the conditions set out in subparagraph 4(3)(b)(i) or clause 4(3)(b)(ii)(A) or (B) are met, the calendar year before the calendar year during which the main assembly of the vocational vehicle, incomplete vocational vehicle, tractor or incomplete tractor in which the engine is installed is completed; and
(b) the s
The text continues in the official source.
