Beta
SOR-2011-87:en
SOR-2011-87:en — Aviation Occupational Health and Safety Regulations
Beta. Legal information, not legal advice. LEGALDIGM is not a law firm. Check the official source for the current text.
Analyze this law with AI1.1 (1) The following definitions apply in these Regulations.
Act means Part II of the Canada Labour Code. (Loi)
approved organization means an organization that is approved by any province for the teaching of first aid. (organisme agréé)
CSA means the Canadian Standards Association. (CSA)
oxygen-deficient atmosphere means an atmosphere in which there is less than 18% by volume of oxygen at a pressure of one atmosphere or in which the partial pressure of oxygen is less than 135 mm Hg. (air à faible teneur en oxygène)
protection equipment includes safety materials, equipment, devices and clothing. (équipement de protection)
qualified person means, in respect of a specified duty, a person who, because of their knowledge, training and experience, is qualified to perform that duty safely and properly. (personne qualifiée)
readily available means, in respect of a document, present and easily accessible at the work place at all times. (facilement accessible)
safety restraining device means a safety harness, seat, rope, belt, strap, chain or lifeline designed to be used by a person to protect them from falling and includes every fitting, fastening or accessory attached to it. (dispositif de retenue)
(2) The incorporation by reference of any standard in these Regulations is an incorporation of the standard as amended from time to time.
(3) Despite any provision in any standard incorporated by reference in these Regulations, a reference to another publication in that standard is a reference to the publication as amended from time to time.
1.11 These Regulations apply to any person who is not an employee but who performs for an employer to which these Regulations apply activities whose primary purpose is to enable the person to acquire knowledge or experience, and to the employer, as if that person were an employee of the employer, and every provision of these Regulations must be read accordingly.
1.2 These Regulations apply in respect of employees employed on board aircraft while in operation and in respect of persons granted access to those aircraft by the employer.
1.3 If an employer is required by section 125 or 125.1 of the Act to keep a record the employer shall keep and maintain the record and make it readily available for examination by the Head of Compliance and Enforcement, the policy committee or, if there is no policy committee, the work place committee or the health and safety representative for the work place to which it applies.
1.4 In the event of an inconsistency between any standard incorporated by reference in these Regulations and any other provision of these Regulations, that other provision prevails to the extent of the inconsistency.
2.1 The following definitions apply in this Part.
A-weighted sound pressure level means a sound pressure level as determined by a measurement system that includes an A-weighting filter that its manufacturer represents as meeting the requirements set out in the International Electrotechnical Commission International Standard IEC 61672-1:2002(E), 1st edition 2002-2005 Electroacoustics – Sound Level Meters. (niveau de pression acoustique pondérée A)
dBA means decibel A-weighted and is a unit of A-weighted sound pressure level. (dBA)
noise exposure level (Lex,8) means 10 times the logarithm to the base 10 of the time integral over any 24-hour period of a squared A-weighted sound pressure divided by 8, the reference sound pressure being 20 μPa. (niveau d’exposition (Lex,8))
sound level meter means a device for measuring sound pressure level that its manufacturer represents as meeting the performance requirements for a Type 2 instrument as specified in the International Electrotechnical Commission International Standard IEC 61672-1:2002(E), 1st edition 2002-2005 Electroacoustics – Sound Level Meters. (sonomètre)
sound pressure level means 20 times the logarithm to the base 10 of the ratio of the root mean square pressure of a sound to the reference sound pressure of 20 μPa, expressed in decibels. (niveau de pression acoustique)
2.2 (1) For the purposes of this Part, the exposure of an employee to sound shall be measured using an instrument that
(a) is recommended for that measurement in clause 4.3 of CSA Standard CAN/CSA-Z107.56-13, Measurement of Noise Exposure; and
(b) is certified, by a certification body accredited by the Standards Council of Canada to grant the certification, as meeting the requirements for such an instrument set out in clause 4 of that Standard.
(2) The exposure of an employee to sound shall be measured in accordance with clauses 5, 6.4.1, 6.4.4, 6.5.2, 6.5.4, 6.6.2 and 6.6.4 of the Standard referred to in paragraph (1)(a).
(3) For the purposes of this Part, the measurement and calculation of the noise exposure level (Lex,8) to which an employee is exposed shall take into account their exposure to A-weighted sound pressure levels of 74 dBA and greater.
(4) For the purposes of this Part, the measurement and calculation of the noise exposure level (Lex,8) may also take into account the exposure of the employee to A-weighted sound pressure levels that are less than 74 dBA.
2.3 (1) If an employee may be exposed, to an A-weighted sound pressure level equal to or greater than 84 dBA for a period that is likely to endanger the employee’s hearing, the employer shall, without delay,
(a) appoint a qualified person to carry out an investigation of the degree of potential exposure; and
(b) notify the work place committee or the health and safety representative of the investigation and the name of the person appointed to carry out the investigation.
(2) The measurement of the A-weighted sound pressure level shall be performed instantaneously, during normal working conditions, using the slow response setting of a sound level meter.
(3) In the investigation referred to in subsection (1), the following matters shall be considered:
(a) the sources of sound on board the aircraft;
(b) the A-weighted sound pressure levels to which the employee is likely to be exposed and the duration of such exposure;
(c) the methods being used to reduce the exposure;
(d) whether the exposure of the employee is likely to exceed the limits established by paragraph 2.4(a); and
(e) whether the employee is likely to be exposed to a noise exposure level (Lex,8) equal to or greater than 84 dBA.
(4) On completion of the investigation and after consultation with the work place committee or the health and safety representative, the person appointed to carry out the investigation shall write, sign and date a report setting out their
(a) observations respecting the matters considered under subsection (3);
(b) recommendations respecting the measures that should be taken in order to comply with sections 2.4 to 2.8; and
(c) recommendations respecting the use of hearing protectors by employees who are exposed to a noise exposure level (Lex,8) equal to or greater than 84 dBA but not greater than 87 dBA.
(5) The report shall be kept by the employer at a location accessible to affected employees for a period of 10 years after the date of the report.
(6) If it is stated in the report that an employee is likely to be exposed to a noise exposure level (Lex,8) equal to or greater than 84 dBA, the employer shall, without delay,
(a) provide the employee with written information describing the hazards associated with exposure to high levels of sound;
(b) make the report readily available to the employee; and
(c) post and keep posted in a conspicuous place at a location accessible to the employee a notice stating where the report may be reviewed.
2.4 No employee shall, in any 24-hour period, be exposed to
(a) an A-weighted sound pressure level set out in column 1 of the schedule to this Part for a duration of exposure exceeding the applicable duration set out in column 2; or
(b) a noise exposure level (Lex,8) that exceeds 87 dBA.
2.5 If feasible, every employer shall, by engineering controls or other physical means other than hearing protectors, reduce an employee’s exposure to a sound level that does not exceed the limits referred to in section 2.4.
2.6 If it is not feasible for an employer, without providing hearing protectors to maintain an employee’s exposure to a sound level that does not exceed the limits referred to in section 2.4, the employer shall, without delay,
(a) make a report in writing to the Head of Compliance and Enforcement setting out the reasons why it is not feasible to do so; and
(b) provide a copy of the report to the work place committee or the health and safety representative.
2.7 (1) If an employer is required to make a report in accordance with section 2.6, the employer shall, as soon as feasible, provide every employee who is exposed to the sound level referred to in section 2.4 with a hearing protector that
(a) is certified, by a certification body accredited by the Standards Council of Canada to grant the certification, as meeting the requirements set out in CSA Standard CAN/CSA–Z94.2-02 (R2007), Hearing Protection Devices — Performance, Selection, Care and Use; and
(b) prevents the exposure to the sound level referred to in section 2.4.
(2) If an employer provides a hearing protector to an employee under subsection (1), the employer shall, in consultation with the work place committee or the health and safety representative, formulate and implement a program to train the employee in the fitting, care and use of the hearing protector.
2.8 If an employee may be exposed to an A-weighted sound pressure level that is likely to exceed the limits established by paragraph 2.4(a), the employer shall ensure that employees are warned, in writing and by signage on board the aircraft, of a potentially hazardous level of sound on board the aircraft.
3.1 In this Part, electrical equipment means equipment for the generation, distribution or use of electricity.
3.2 [Repealed, SOR/2019-246, s. 360]
3.3 All testing or work performed on electrical equipment on board an aircraft shall be performed by a qualified person.
3.4 If there is a risk that an employee may receive a hazardous electrical shock during the performance of the work referred to in section 3.3, the employee shall use insulated protection equipment and tools that will protect the employee from injury.
3.5 If electrical equipment on board an aircraft is live or may become live, no employee shall work on the equipment unless
(a) the employer has instructed the employee in procedures that are safe for work on live conductors;
(b) a safety ground is connected to the equipment; or
(c) the equipment is separated or disconnected from every source of electrical, hydraulic, pneumatic or other kind of energy that is capable of making electrical equipment dangerous.
3.6 If an employee is working on or near electrical equipment that is live or may become live, the employer shall ensure that the electrical equipment is guarded.
3.7 If two or more employees are working on or in connection with electrical equipment, they shall be fully informed by the employer with respect to ensuring that the work is coordinated in a safe manner.
3.8 If an employee identifies a defect in electrical equipment that may render it unsafe for use, the employee shall, as soon as possible, mark or tag the electrical equipment as unsafe for use and report the defect to the person in charge of the aircraft.
4.1 The following definitions apply in this Part.
galley area means an area used for the storage or preparation of food on board an aircraft. (office)
washroom means a room on board an aircraft that contains a toilet or a washbasin. (salle d’eau)
4.2 (1) If feasible, the employer shall provide a room that contains a toilet and a washbasin.
(2) If it is not feasible to comply with subsection (1), the employer shall, if feasible, provide a room that contains a toilet.
(3) If it is not feasible to comply with subsection (1) or (2), the employer shall, if feasible, provide a room that contains a washbasin.
(4) If feasible, the employer shall provide a washroom for the sole use of the employees.
4.3 (1) Every employer shall ensure that each washroom and galley area used by employees is maintained in a clean and sanitary condition and cleaned at least once in every 24 hour period in which they are used.
(2) Employees who use washrooms and galley areas shall keep them as clean and in as sanitary a condition as possible.
(3) All work that may cause dusty or unsanitary conditions shall be carried out in a manner that will prevent the contamination of the air by dust or other substances injurious to health.
4.4 (1) Each container that is used for solid or liquid waste, other than a disposable plastic garbage bag, shall be
(a) leak-proof;
(b) constructed so that it can be easily cleaned and maintained in a sanitary condition; and
(c) equipped with a tight-fitting cover or enclosed in a manner that does not present a health or safety hazard.
(2) Each container shall be emptied as soon as feasible after it becomes full and at least once in every 24-hour period in which it is used.
(3) If disposable plastic garbage bags are used, they shall be
(a) leak-proof;
(b) strong enough to support their contents when full; and
(c) closed and secured when full and disposed of at the first opportunity.
4.5 Every washroom shall be enclosed in such a manner as to provide for a reasonable amount of privacy for its occupant.
4.6 Toilet paper shall be provided in each washroom that contains a toilet.
4.7 (1) The employer must provide the following items in each washroom that contains a toilet:
(a) menstrual products, including clean and hygienic tampons and menstrual pads; and
(b) a covered container for the disposal of menstrual products.
(2) If it is not feasible to provide menstrual products in a washroom, the employer shall provide them in another location in the same work place that is controlled by the employer, accessible by employees at all times and offers a reasonable amount of privacy.
4.8 If vermin have entered any enclosed part of a work place, the employer shall, as soon as feasible, take all steps necessary to eliminate the vermin and prevent their re-entry.
4.9 (1) In those washrooms that contain a washbasin, every employer shall ensure that the water supply to the washbasin is sufficient to serve the employees.
(2) In every washroom that contains a washbasin, the employer shall ensure that the following are provided:
(a) soap or other cleaning agent in a dispenser at each washbasin;
(b) single-use hand towels in sufficient quantity to serve the employees using the washroom; and
(c) a non-combustible container for the disposal of used towels.
(3) If hot water is provided for personal washing, it shall be maintained at a temperature of not more than 43°C.
(4) If it is not feasible to comply with subsection (1), the employer shall ensure that sufficient antiseptic agent is provided to employees.
4.10 (1) Every employer shall ensure that employees are provided with potable water in sufficient quantity for drinking, personal washing and food preparation.
(2) The potable water shall meet the microbiological quality guidelines set out in the Guidelines for Canadian Drinking Water Quality, prepared by the Federal-Provincial-Territorial Committee on Drinking Water and published by the Department of Health.
4.11 If a portable storage container for potable water is used,
(a) the container shall be equipped with an airtight cover that can be securely closed;
(b) the container shall be used only for the purpose of storing potable water;
(c) the container shall not be stored in a washroom; and
(d) the water shall be drawn from the container by a tap, a ladle used only for the purpose of drawing water from the container or any other means that precludes the contamination of the water.
4.12 If potable water is not supplied by a drinking fountain the employer shall provide sanitary single-use drinking cups or bottled water.
4.13 Any ice that is added to potable water or used for the contact refrigeration of foodstuffs shall be
(a) made from potable water; and
(b) stored and handled in a manner that prevents contamination.
4.14 (1) Each employee who handles food as part of their duties shall be instructed and trained in food handling practices to follow in order to prevent the contamination of food.
(2) No employee who is suffering from a disease that can be transmitted through the handling of food shall handle food.
4.15 Food stored by an employer for the consumption by employees shall be stored in conditions that will prevent the food from becoming a hazard to the employees when consumed.
4.16 All equipment and utensils that come into contact with food shall be
(a) smooth and free from cracks, crevices, pitting or unnecessary indentations; and
(b) cleaned to maintain their surfaces in a sanitary condition.
4.17 No person shall prepare, store or eat food
(a) in a place where a hazardous substance may contaminate food, dishes or utensils;
(b) in a washroom; or
(c) in any other place where food may be contaminated.
4.18 (1) If dry ice is used for the refrigeration of food, it shall be
(a) contained in a manner that prevents injury to employees; and
(b) marked, tagged or otherwise identified in a manner that assists employees in using it safely.
(2) An employee who handles or is exposed to dry ice shall be instructed and trained in precautions to be taken for its safe use and procedures to follow in the event of injury.
4.19 Food waste and garbage shall be
(a) handled in a manner that prevents the contamination of food;
(b) held in leak-proof, non-absorptive, easily-cleaned containers with tight-fitting covers, in a separate enclosed area or container, until removal for disposal; and
(c) removed as frequently as is necessary to prevent unsanitary conditions.
4.20 If meals are provided for employees, the employer shall ensure that a clean and sanitary eating area is provided.
4.21 All reusable equipment that may expose an employee to a health hazard shall be maintained in a clean and sanitary condition.
5.1 The following definitions apply in this Part.
airborne asbestos fibres means asbestos fibres that are longer than 5 μm (micrometres) with an aspect ratio equal to or greater than 3:1 and that are carried by the air. (fibres d’amiante aéroportées)
asbestos means actinolite, amosite, anthophyllite, chrysotile, crocidolite and tremolite in their fibrous form. (amiante)
asbestos-containing material means
(a) any article that is manufactured and contains 1% or more asbestos by weight at the time of manufacture or that contains a concentration of 1% or more asbestos as determined in accordance with Method 9002 set out in the document entitled NIOSH Manual of Analytical Methods, published by the National Institute for Occupational Safety and Health, as amended from time to time, or in accordance with a scientifically proven method used to collect and analyze a representative sample of the material; and
(b) any material that contains a concentration of 1% or more asbestos as determined in accordance with Method 9002 set out in the document entitled NIOSH Manual of Analytical Methods, published by the National Institute for Occupational Safety and Health, as amended from time to time, or in accordance with a scientifically proven method used to collect and analyze a representative sample of the material. (matériau contenant de l’amiante)
clearance air sampling means the action of taking samples to determine if the concentration of airborne asbestos fibres inside an enclosure is below the limit referred to in section 5.16 to permit the dismantling of a containment system. (échantillonnage de l’air après décontamination)
containment system means an isolation system that is designed to effectively contain asbestos fibre within a designated work area where asbestos-containing material is handled, removed, encapsulated or enclosed. (confinement)
encapsulation means the treatment of an asbestos-containing material with a sealant that penetrates the material and binds the asbestos fibres together, and the treatment of the surface of the asbestos-containing material with a sealant that creates a membrane on the surface, to prevent the release of asbestos fibres into the air. (encapsulation)
enclosure means a physical barrier such as drywall, plywood or metal sheeting that, as part of the containment system, isolates asbestos-containing material from adjacent areas in a building to prevent the release of airborne asbestos fibres into those areas. (encloisonnement)
friable means, in respect of asbestos-containing material, that the material, when dry, can be easily crumbled or powdered by hand pressure. (friable)
glove bag means a polyethylene or polyvinyl chloride bag that is affixed around an asbestos-containing source and that permits asbestos-containing material to be removed while minimizing the release of airborne asbestos fibres into the work place. (sac à gants)
hazard information means, in respect of a hazardous substance, information on the proper and safe storage, handling, use and disposal of the hazardous substance, including information relating to the health and physical hazards that it presents. (renseignements sur les risques)
HEPA filter means a high-efficiency particulate air filter that has been tested to ensure efficiency equal to or exceeding 99.97% for removal of airborne particles having a mean aerodynamic diameter of 0.3 µm (micrometres) from the air. (filtre HEPA)
high-risk activity means an activity that involves the handling or disturbance of friable asbestos-containing material or is carried out in proximity to friable asbestos-containing material, that requires a high level of control to prevent exposure to excessive concentrations of airborne asbestos fibres and that includes
(a) the removal or disturbance of more than 1 m2 of friable asbestos-containing material in a work place, even if the activity is divided into smaller jobs,
(b) the spray application of a sealant to a friable asbestos-containing material,
(c) the cleaning or removal of air-handling equipment, other than filters, in a building that has sprayed-on fireproofing or sprayed-on thermal insulation that is asbestos-containing material,
(d) the repair, alteration or demolition of all or part of a kiln, metallurgical furnace or similar structure that contains asbestos-containing material,
(e) the breaking, cutting, drilling, abrading, grinding, sanding or vibrating of non-friable asbestos-containing material, if the activity is carried out by means of power tools that are not attached to dust-collecting devices equipped with HEPA filters, and
(f) the repair, alteration or demolition of all or part of a building in which asbestos is or was used in the manufacture of products, unless the asbestos was cleaned up and removed. (activité à risque élevé)
lower explosive limit means the lower limit of flammability of a chemical agent or a combination of chemical agents at ambient temperature and pressure, expressed
(a) for a gas or vapour, as a percentage in air by volume; and
(b) for dust, as the weight of dust per volume of air. (limite explosive inférieure)
low-risk activity means an activity that involves the handling of asbestos-containing material or is carried out in proximity to non-friable asbestos-containing material and that includes
(a) the installation or removal of ceiling tiles that are made of non-friable asbestos-containing material and cover an area of less than 7.5 m2,
(b) the installation or removal of other non-friable asbestos-containing material, if the material is not being broken, cut, drilled, abraded, ground, sanded or vibrated and dust is not being generated,
(c) the breaking, cutting, drilling, abrading, grinding, sanding or vibrating of non-friable asbestos-containing material, if the material is wetted to control the spread of dust or fibres and the activity is carried out only by means of non-powered hand-held tools, and
(d) the removal of less than 1 m² of drywall in which joint cement containing asbestos has been used. (activité à faible risque)
moderate-risk activity means an activity that involves the handling of asbestos-containing material or is carried out in proximity to friable asbestos-containing material, that is not otherwise classified as a low-risk activity or high-risk activity and that includes
(a) the removal of all or part of a false ceiling to gain access to a work area, if asbestos-containing material is likely to be found on the surface of the false ceiling,
(b) the removal or disturbance of 1 m2 or less of friable asbestos-containing material during repair, alteration, maintenance or demolition work in a work place,
(c) the enclosure of friable asbestos-containing material,
(d) the application of tape, sealant or other covering to pipe or boiler insulation that is asbestos-containing material,
(e) the removal of ceiling tiles that are asbestos-containing material, if the tiles cover an area of greater than 2 m2 and are removed without being broken, cut, drilled, abraded, ground, sanded or vibrated,
(f) the breaking, cutting, drilling, abrading, grinding, sanding or vibrating of non-friable asbestos-containing material, if the material is not wetted to control the spread of dust or fibres and the activity is carried out only by means of non-powered hand-held tools,
(g) the removal of 1 m2 or more of drywall in which joint cement that is asbestos-containing material has been used,
(h) the breaking, cutting, drilling, abrading, grinding, sanding or vibrating of non-friable asbestos-containing material, if the activity is carried out by means of power tools that are attached to dust-collecting devices equipped with HEPA filters,
(i) the removal of insulation that is asbestos-containing material from a pipe, duct or similar structure using a glove bag, and
(j) the cleaning or removal of filters used in air-handling equipment in a building that has sprayed-on fireproofing that is asbestos-containing material. (activité à risque modéré)
product identifier has the same meaning as in subsection 1(1) of the Hazardous Products Regulations. (identificateur de produit)
readily available[Repealed, SOR/2025-79, s. 36]
supplier has the same meaning as in section 2 of the Hazardous Products Act. (fournisseur)
work activity means any low-risk activity, moderate-risk activity or high-risk activity or any activity that is ancillary to that activity, and the supervision of that activity and that ancillary activity. (activité de travail)
5.2 This Part does not apply to the handling or transportation of dangerous goods to which the Transportation of Dangerous Goods Act, 1992 and regulations made under that Act apply.
5.3 Every employer shall keep a record of all hazardous substances that are used, handled or stored for use on board an aircraft and may either keep such a record in the work place or keep a centralized record in respect of several work places.
5.4 (1) If the health or safety of an employee is likely to be endangered by exposure to a hazardous substance in a work place, the employer shall, without delay,
(a) appoint a qualified person to carry out an investigation in that regard; and
(b) notify the work place committee or the health and safety representative of the proposed investigation, and of the name of the qualified person appointed to investigate, so that they may participate in the investigation.
(2) In an investigation, the following criteria shall be taken into consideration:
(a) the chemical, biological and physical properties of the hazardous substance;
(b) the routes of exposure to the hazardous substance;
(c) the acute and chronic effects on health of exposure to the hazardous substance;
(d) the quantity of the hazardous substance to be handled;
(e) the manner in which the hazardous substance is stored, used, handled and disposed of;
(f) the control methods used to eliminate or reduce exposure of the employees to the hazardous substance;
(g) the concentration or level of the hazardous substance to which an employee is likely to be exposed; and
(h) whether the concentration of an airborne chemical agent or the level of ionizing or non-ionizing radiation is likely to exceed 50% of the values referred to in section 5.16 or the limits referred to in subsection 5.19(2).
5.5 On completion of the investigation and after consultation with the work place committee or the health and safety representative,
(a) the qualified person shall sign a written report setting out
(i) the person’s observations respecting the criteria considered in accordance with subsection 5.4(2), and
(ii) the person’s recommendations respecting the manner of compliance with sections 5.7 to 5.19, including recommendations respecting sampling and testing methods; and
(b) the employer shall develop and implement a written procedure for the control of the concentration or level of the hazardous substance on board an aircraft and make it readily available for examination by employees in any form, as determined in consultation with the policy committee or, if there is no policy committee, the work place committee or the health and safety representative.
5.6 The report shall be kept by the employer for a period of 30 years from the day on which the qualified person signs the report.
5.7 (1) If the report recommends a medical examination for the employees likely to be exposed to a hazardous substance, the employer shall consult a physician to ascertain the necessity for that medical examination.
(2) For the purposes of subsection (1), a physician shall conclude that a medical examination is necessary only if, in light of the factors referred to in subsection 5.4(2), the likelihood and consequences of exposure to the hazardous substance outweigh the intrusiveness of the medical examination or the disruption to bodily integrity that might be necessary.
(3) If a physician considers that a medical examination is necessary, the employer shall not permit an employee to handle the hazardous substance unless a physician acceptable to the employee has examined the employee and declared the employee fit, or fit with restrictions, to handle the hazardous substance.
(4) For the purposes of determining whether an employee is fit, or fit with restrictions, a physician shall
(a) take into account
(i) the factors referred to in subsection 5.4(2), and
(ii) the likely effects of handling the hazardous substance on the employee’s health and that of other employees and the capacity of the employee to perform the work; and
(b) perform only those tests or examinations that are necessary to make that determination.
(5) If the physician examining an employee under subsection (3) declares the employee fit with restrictions to handle the hazardous substance, the employer shall not permit the employee to handle the hazardous substance except in accordance with the specified restrictions.
(6) If an employer consults a physician under subsection (1), the employer shall keep a copy of the physician’s decision with the report referred to in section 5.5.
(7) The cost of a medical examination referred to in subsection (3) shall be borne by the employer.
5.8 Every hazardous substance on board an aircraft shall be stored, handled or used in a manner that minimizes the hazard related to that substance.
5.9 If a hazardous substance is stored, handled or used on board an aircraft, any hazard resulting from that storage, handling or use shall be confined to as small an area as possible.
5.10 Every container for a hazardous substance that is used on board an aircraft shall be designed and constructed so that it protects the employees from any health or safety hazard that is caused by the hazardous substance.
5.11 The quantity of a hazardous substance for use or processing on board an aircraft shall, if feasible, be limited to the minimum quantity required.
5.12 If a hazardous substance is on board an aircraft, signs shall be posted in conspicuous places on board the aircraft warning of the presence of the hazardous substance and stating any precautions to be taken to prevent or reduce any health or safety hazard.
5.13 (1) Every employer shall, in consultation with the policy committee or, if there is no policy committee, the work place committee or the health and safety representative, develop and implement an employee education and training program with respect to hazard prevention and control on board an aircraft, including with respect to hazardous substances.
(2) The employee education and training program shall include
(a) the education and training of each employee who handles or is exposed to or who is likely to handle or be exposed to a hazardous substance, with respect to
(i) the product identifier of the hazardous substance,
(ii) all hazard information disclosed by the supplier or by the employer on a safety data sheet or label,
(iii) all hazard information of which the employer is aware or ought to be aware,
(iv) the observations referred to in subparagraph 5.5(a)(i),
(v) the information disclosed on a safety data sheet referred to in section 5.21 and the purpose and significance of that information, and
(vi) in respect of hazardous products on board an aircraft, the information required to be disclosed on a safety data sheet and on a label under Division 3 and the purpose and significance of that information;
(b) the education and training of each employee who is referred to in paragraph (a), with respect to
(i) the procedures to follow to implement sections 5.8 and 5.9,
(ii) the procedures to follow for the safe storage, handling, use and disposal of hazardous substances, including procedures to be followed in an emergency involving a hazardous substance, and
(iii) the procedures to follow if an employee on board an aircraft is exposed to a hazardous product in gas, liquid, solid, vapour, fume, mist, fog or dust form that escapes from processing equipment, from control emission equipment or from a product that is outside of or on board the aircraft; and
(c) the education and training of each employee on the procedures to follow to access electronic or paper versions of reports, records of education and training given and safety data sheets.
(3) Every employer shall, in consultation with the policy committee or, if there is no policy committee, the work place committee or the health and safety representative, review and, if necessary, revise the employee education and training program
(a) at least once a year;
(b) whenever there is a change in conditions in respect of the presence of hazardous substances on board an aircraft; and
(c) whenever new hazard information in respect of a hazardous substance on board an aircraft becomes available to the employer.
5.14 The employer shall keep a paper or electronic record of the education and training given to every employee and shall
(a) make it readily available for examination by the employee in any form, as determined in consultation with the policy committee or, if there is no policy committee, the work place committee or the health and safety representative; and
(b) keep it for a period of two years from the day on which the employee ceases to handle or be exposed to the hazardous substance, or is no longer likely to handle or be exposed to the hazardous substance.
5.15 No person shall use a hazardous substance in a work place if a non-hazardous substance or one that is less hazardous can be used instead.
5.16 (1) No employee shall be exposed to a concentration of an airborne chemical agent, other than airborne asbestos fibres, in excess of the value for that chemical agent adopted by the American Conference of Governmental Industrial Hygienists in its publication entitled Threshold Limit Values (TLVs) and Biological Exposure Indices (BEIs), as amended from time to time.
(1.1) An employer shall ensure that an employee’s exposure to a concentration of airborne asbestos fibres is as close to zero as possible, but in any event the employer shall ensure that the concentration does not exceed the value for airborne asbestos fibres adopted by the American Conference of Governmental Industrial Hygienists in its publication entitled Threshold Limit Values (TLV) and Biological Exposure Indices (BEI), as amended from time to time.
(2) If the concentration of an airborne chemical agent is likely to exceed the value referred to in subsection (1) or if the concentration of airborne asbestos fibres is likely to exceed zero, air samples shall be taken by a qualified person and the concentration of the chemical agent or the airborne asbestos fibres shall be determined
(a) in accordance with the standards set out by the United States National Institute for Occupational Safety and Health in the NIOSH Manual of Analytical Methods; or
(b) if no specific standards for the chemical agent are listed in the document referred to in paragraph (a), in accordance with a scientifically proven method used to collect and analyze a representative sample of the chemical agent.
(3) A paper or electronic record of each determination made under subsection (2) shall be kept by the employer at a location accessible to affected employees, for a period of 3 years from the date of the determination.
(4) The record shall include
(a) the date, time and location of the analysis;
(b) the hazardous substance in respect of which the analysis was made;
(c) the sampling and testing method used;
(d) the result obtained; and
(e) the name and occupation of the person who made the analysis.
5.17 (1) Subject to subsection (2), the concentration of an airborne chemical agent or combination of airborne chemical agents on board an aircraft shall be less than 50% of the lower explosive limit of the chemical agent or combination of chemical agents.
(2) If a source of ignition may ignite an airborne chemical agent or combination of airborne chemical agents on board an aircraft, the concentration of the chemical agent or the combination of chemical agents shall not exceed 10% of the lower explosive limit of the chemical agent or combination of chemical agents.
5.18 If feasible, the employer shall provide automated warning and detection systems if the seriousness of any exposure to a hazardous substance requires the use of those systems.
5.19 (1) If a device that is capable of producing and emitting energy in the form of electromagnetic waves or acoustical waves is used on board an aircraft, the radiation to which an employee is exposed shall not exceed the limits recommended in Chapter 2 of Safety Code 6, Limits of Human Exposure to Radiofrequency Electromagnetic Fields in the Frequency Range from 3 kHz to 300 GHz published by the Department of Health.
(2) If an employee works on or near a device that may emit nuclear energy, the employer shall ensure that the exposure of the employee to nuclear energy does not exceed the radiation dose limits set out in the Radiation Protection Regulations.
5.19.1 (1) If asbestos-containing material is present in a work place and there is the potential for a release of asbestos fibres or employee exposure to asbestos fibres, an employer shall ensure that the qualified person who is carrying out a hazard investigation under section 5.4 takes into consideration the type of asbestos, the condition of the asbestos-containing material, the friability of the asbestos-containing material, the accessibility to and likelihood of damage to the asbestos-containing material and the potential for the release of asbestos fibres or employee exposure to asbestos fibres.
(2) At the completion of an investigation carried out under section 5.4, the employer shall ensure that a record of the location, friability and condition of the asbestos-containing material and the type of asbestos contained in that material is kept and made readily available for examination by employees and is in any form as determined in consultation with the policy committee or, if there is no policy committee, the work place committee or the health and safety representative.
5.19.2 Before undertaking any work activity that involves asbestos-containing material, an employer shall, in consultation with the policy committee or, if there is no policy committee, the work place committee or the health and safety representative, develop, implement and administer an asbestos exposure control plan that requires the employer to
(a) ensure that a hazard investigation under section 5.4 has been carried out by a qualified person and, in the event that there is a change in the work activity, review any report that was prepared as a result of the investigation and, if necessary, have a qualified person carry out another investigation;
(b) ensure that a qualified person classifies the work activity as a low-risk activity, moderate-risk activity or high-risk activity;
(c) ensure that all asbestos-containing material present in the work place that is exposed or that will be disturbed is identified by signs and labels or by any other effective manner;
(d) ensure that all friable asbestos-containing material present in the work place is controlled by removal, enclosure or encapsulation or by any other effective manner to prevent employee exposure to asbestos;
(e) ensure that procedures and control measures for moderate-risk activities and high-risk activities are developed and implemented; and
(f) develop and implement an employee education and training program that is specific to asbestos-containing material.
5.19.3 If an employee who is undertaking automotive service procedures may be exposed to asbestos from friction material or dust arising from that material, an employer shall ensure that
(a) the use of compressed air, brushes or similar means to dry-remove friction material dust from automotive assemblies is prohibited; and
(b) signs to advise employees of the hazards and required precautions are posted in service work areas where friction material is handled or dust arising from that material is generated.
5.19.4 (1) During any work activities that involve friable asbestos-containing materials, an employer shall ensure that the following activities are carried out frequently and at regular intervals as determined by a qualified person, at the end of each work shift and immediately after the work activity is completed:
(a) all asbestos dust, waste and debris are removed by vacuuming with a vacuum cleaner that is equipped with a HEPA filter, damp-mopping or wet-sweeping the area that is contaminated with the asbestos dust, waste or debris; and
(b) any drop sheets that are contaminated with asbestos dust, waste or debris are wetted.
(2) All asbestos dust, waste or debris and any drop sheets that are contaminated with asbestos dust, waste or debris shall be placed in a container referred to in section 5.19.11.
5.19.5 If a glove bag is used for the removal of asbestos insulation from pipes, ducts and similar structures, an employer shall ensure that
(a) the glove bag is sealed to prevent the release of asbestos fibres into the work area;
(b) the glove bag is inspected for damage or defects immediately before it is attached to the pipe, duct or similar structure and at regular intervals during its use;
(c) all waste from asbestos-containing material that is on surfaces is washed to the bottom of the glove bag and all exposed asbestos-containing material is encapsulated when it is inside the glove bag;
(d) the glove bag is evacuated using a vacuum cleaner that is equipped with a HEPA filter to remove the air inside the bag prior to the removal of the glove bag; and
(e) after the glove bag is removed, all exposed surfaces are cleaned with a damp cloth and a vacuum cleaner that is equipped with a HEPA filter.
5.19.6 (1) Before leaving a work area that is contaminated with asbestos-containing material, an employee shall
(a) if their protective clothing is to be reused, decontaminate the clothing with a damp cloth or a vacuum cleaner that is equipped with a HEPA filter before taking the clothing off; or
(b) if their protective clothing is not to be reused, place the clothing in a container referred to in section 5.19.11.
(2) An employer shall provide employees with a facility reserved for washing their hands and face, and employees shall wash their hands and face using that facility before leaving a work area that is contaminated with asbestos-containing material.
5.19.7 As soon as feasible after any work activity that involves asbestos-containing material is completed, an employee shall clean reusable tools, equipment, rigid barriers and portable enclosures that are contaminated with asbestos with a damp cloth or a vacuum cleaner that is equipped with a HEPA filter.
5.19.8 (1) An employer shall ensure that a qualified person takes air samples to test for airborne asbestos fibres
(a) in the vicinity of the containment system during any work activity that involves asbestos-containing material and, in the case of a work activity that lasts longer than 24 hours, at least daily;
(b) in the clean room during removal and clean-up operations and, in the case of removal and clean-up operations that last longer than 24 hours, at least daily; and
(c) in contaminated areas that are inside the containment system as necessary during removal and clean-up operations.
(2) The employer shall ensure that the following air samples are taken:
(a) two samples for every area in an enclosure that is 10 m2 or less;
(b) three samples for every area in an enclosure that is more than 10 m2 and not more than 500 m2; and
(c) five samples for every area in an enclosure that is more than 500 m2.
(3) Within 24 hours after obtaining the air sampling test results, the employer shall
(a) post a copy of the results in a conspicuous place in the work place; and
(b) make the results available to the policy committee, if any, the work place committee and the health and safety representative.
5.19.9 (1) Before dismantling a containment system and after all asbestos dust, waste and debris have been cleaned up, removed or encapsulated, an employer shall ensure that clearance air samples are taken inside the enclosure and that the concentration of airborne asbestos fibres is determined in accordance with Method 7400 set out in the document entitled NIOSH Manual of Analytical Methods, published by the National Institute for Occupational Safety and Health, as amended from time to time, or in accordance with a scientifically proven method used to collect and analyze a representative sample of airborne asbestos fibres.
(2) When conducting clearance air sampling, the employer shall ensure that forced air is used inside the enclosure to dislodge any asbestos fibres from all surfaces and keep them airborne.
(3) Clearance air sampling shall be taken until the concentrations of airborne asbestos fibres do not exceed the values referred to in subsection 5.16(1.1).
5.19.10 Within 24 hours after obtaining the clearance air sampling test results, the employer shall
(a) post a copy of the results in a conspicuous place in the work place; and
(b) make the results available to the policy committee, if any, the work place committee and the health and safety representative, and provide a copy of the results to the Head of Compliance and Enforcement.
5.19.11 Containers for the containment of asbestos dust, waste and debris and asbestos-containing material shall be
(a) dust-tight;
(b) suitable to contain the dust, waste or debris;
(c) impervious to asbestos;
(d) identified as containing asbestos dust, waste or debris;
(e) cleaned with a damp cloth or a vacuum cleaner that is equipped with a HEPA filter immediately before being removed from the work area; and
(f) removed from the work place frequently and at regular intervals as determined by a qualified person.
5.20 Every container of a hazardous substance, other than a hazardous product, that is stored, handled, used or pending disposal on board an aircraft shall be labelled in a manner that discloses clearly the generic name of the substance and the hazard information in respect of the substance.
5.21 If a safety data sheet in respect of a hazardous substance, other than a hazardous product, that is stored, handled, used or pending disposal on board an aircraft may be obtained from the supplier of the hazardous substance, the employer shall obtain a copy of the safety data sheet and make it readily available for examination by employees in any form, as determined in consultation with the policy committee or, if there is no policy committee, the work place committee or the health and safety representative.
5.22 The following definitions apply in this Division.
bulk shipment has the same meaning as in subsection 5.5(1) of the Hazardous Products Regulations. (expédition en vrac)
container means any package or receptacle, including a bag, barrel, bottle, box, can, cylinder, drum and storage tank. (contenant)
hazardous waste means a hazardous product that is acquired or generated for recycling or recovery or is intended for disposal. (résidu dangereux)
significant new data has the same meaning as in subsection 5.12(1) of the Hazardous Products Regulations. (nouvelles données importantes)
supplier label means a label prepared by a supplier that discloses any information elements required by the Hazardous Products Act. (étiquette du fournisseur)
supplier safety data sheet means a safety data sheet prepared by a supplier that discloses any information elements required by the Hazardous Products Act. (fiche de données de sécurité du fournisseur)
work place label means a label prepared by an employer in accordance with this Division. (étiquette du lieu de travail)
work place safety data sheet means a safety data sheet prepared by an employer in accordance with subsection 5.25(1). (fiche de données de sécurité du lieu de travail)
5.23 (1) This Division does not apply in respect of any
(a) tobacco or a tobacco product as defined in section 2 of the Tobacco and Vaping Products Act;
(b) manufactured article as defined in section 2 of the Hazardous Products Act; or
(c) wood or a product made of wood.
(2) This Division, other than section 5.28.1, does not apply to hazardous waste.
5.24 (1) Subsections (2) to (4) do not apply in respect of a hazardous product that is
(a) a hazardous product, other than wood or a product made of wood, that is listed in Schedule 1 to the Hazardous Products Act; or
(b) a nuclear substance, as defined in section 2 of the Nuclear Safety and Control Act, that is radioactive.
(2) If a hazardous product is received on board an aircraft by an employer, the employer shall, without delay, obtain a supplier safety data sheet in respect of the hazardous product from the supplier, unless the employer is already in possession of a supplier safety data sheet that
(a) is for a hazardous product that both has the same product identifier and is from the same supplier;
(b) discloses information that is current at the time that the hazardous product is received; and
(c) was prepared and dated less than three years before the day on which the hazardous product is received.
(3) If the supplier safety data sheet in respect of a hazardous product on board an aircraft is three years old or more, the employer shall, if feasible, obtain from the supplier a current supplier safety data sheet.
(4) If it is not feasible for an employer to obtain a current supplier safety data sheet, the employer shall update the hazard information on the most recent supplier safety data sheet that the employer has received, on the basis of the ingredients disclosed on that supplier safety data sheet and on the basis of any significant new data that becomes available to the employer.
5.25 (1) Subject to section 5.29, if an employer receives a supplier safety data sheet, the employer may prepare a work place safety data sheet to be used on board an aircraft in place of the supplier safety data sheet if
(a) the work place safety data sheet discloses at least the information disclosed on the supplier safety data sheet;
(b) the information disclosed on the work place safety data sheet does not disclaim or contradict the information disclosed on the supplier safety data sheet;
(c) the supplier safety data sheet is readily available for examination by employees in any form, as determined in consultation with the policy committee or, if there is no policy committee, the work place committee or the health and safety representative; and
(d) the work place safety data sheet discloses that the supplier safety data sheet is available on board the aircraft.
(2) An employer shall review the accuracy of the information disclosed on a work place safety data sheet referred to in subsection (1) and update it as soon as feasible after new hazard information or significant new data becomes available to the employer.
(3) If the information required to be disclosed on the work place safety data sheet is not available or not applicable to the hazardous product, the employer shall, in place of the information, insert the words “not available” or “not applicable”, as the case may be, in the English version and the words “non disponible” or “sans objet”, as the case may be, in the French version, of the work place safety data sheet.
5.26 (1) Every employer shall, on board an aircraft in which an employee is likely to handle or be exposed to a hazardous product, keep readily available a copy of the work place safety data sheet or the supplier safety data sheet, as the case may be, in English and in French, for examination by employees and by any policy committee, work place committee or health and safety representative.
(2) The work place safety data sheet and supplier safety data sheet shall be made readily available in any form, as determined in consultation with the policy committee, or if there is no policy committee, the work place committee or the health and safety representative.
5.27 (1) Each hazardous product, other than a hazardous product listed in subsection 5.24(1), on board an aircraft and each container in which the hazardous product is contained on board an aircraft shall, if the hazardous product or the container is received from a supplier,
(a) in the case where the hazardous product is in a bulk shipment, be accompanied by a supplier label;
(b) in the case where the employer has agreed in writing to apply a label to the inner container of the hazardous product, have applied to it a supplier label as soon as feasible after the hazardous product is received from the supplier; and
(c) in any other case, have applied to it a supplier label.
(2) Subject to section 5.29, if a hazardous product, other than a hazardous product listed in subsection 5.24(1), is received from a supplier and an employer places the hazardous product on board an aircraft in a container other than the one in which it was received from the supplier, the employer shall apply to the container a supplier label or work place label that discloses the following information:
(a) the product identifier;
(b) the hazard information in respect of the hazardous product; and
(c) a statement indicating that a safety data sheet for the hazardous product is available on board the aircraft.
(3) Subject to sections 5.28 and 5.29, no person shall remove, deface or modify the supplier label applied to a hazardous product, or its container, that is on board an aircraft.
5.28 (1) If, on board an aircraft, a label applied to a hazardous product or the container of a hazardous product becomes illegible or is removed from the hazardous product or the container, the employer shall replace the label with a work place label that discloses the following information:
(a) the product identifier;
(b) the hazard information in respect of the hazardous product; and
(c) a statement indicating that a safety data sheet for the hazardous product is available on board the aircraft.
(2) An employer shall review the accuracy of the information on a work place label and update it as soon as feasible after new hazard information or significant new data becomes available to the employer.
5.28.1 (1) If a hazardous product on board an aircraft is hazardous waste, the employer shall disclose the generic name and hazard information in respect of the hazardous product by
(a) applying a label to the hazardous waste or its container; or
(b) posting a sign in a conspicuous place near the hazardous waste or its container.
(2) The employer shall provide education and training to employees regarding the safe storage and handling of hazardous waste that is found in the work place.
5.29 (1) If an employer has filed a claim for exemption from the requirement to disclose information on a safety data sheet or on a label under subsection 11(2) of the Hazardous Materials Information Review Act, the employer shall disclose, in place of the information that the employer is exempt from disclosing,
(a) if there is no final disposition of the proceedings in relation to the claim, the date on which the claim for exemption was filed and the registry number assigned to the claim under section 10 of the Hazardous Materials Information Review Regulations; and
(b) if the final disposition of the proceedings in relation to the claim is that the claim is valid, a statement that an exemption has been granted and the date on which the exemption was granted.
(2) However, if a claim for exemption is in respect of a product identifier, the employer shall, on the safety data sheet or label of the hazardous product, disclose, in place of that product, a code name or code number specified by the employer as the product identifier for that hazardous product.
5.30 For the purposes of subsection 125.2(1) of the Act, a medical professional is a nurse who is registered or licensed under the laws of a province.
6.1 (1) If feasible, every employer shall eliminate any health or safety hazard in the work place or reduce it to a safe limit.
(2) If it is not feasible to eliminate a health or safety hazard or reduce it to a safe limit, the employer shall provide every person granted access to the work place who may be exposed to the hazard with protection equipment prescribed by this Part.
6.2 All protection equipment shall be designed to protect the person from the hazard for which it is provided and shall not in itself create a hazard.
6.3 All protection equipment provided by the employer shall be maintained, inspected and tested by a qualified person and, if necessary to prevent a health hazard, be maintained in a clean and sanitary condition by a qualified person.
6.4 If there is a risk of head injury, protective headwear shall be used.
6.5 (1) If there is a risk of foot injury, protective footwear that is certified, by a certification body accredited by the Standards Council of Canada to grant such certification, as meeting the standards set out in CSA Standard CAN/CSA-Z195-09, Protective Footwear, shall be used.
(2) If there is a risk of slipping, non-slip footwear shall be used.
6.6 (1) If, in a workplace, there is a risk of injury to the eyes or face, the employer shall provide every person who is granted access to the work place with eye or face protection equipment that is selected by the employer in accordance with Annex A of CSA Group Standard CSA Z94.3, Eye and face protectors, as amended from time to time, and that meets the requirements set out in that standard.
(2) If there is routine exposure to irritating airborne chemical agents, intense heat, liquid splashes, molten metals or similar agents in a work place, contact lenses shall not be worn.
6.7 If there is a risk of exposure to an airborne hazardous substance or an oxygen-deficient atmosphere, the employer shall provide a respiratory protective device that is selected, fitted, used and maintained in accordance with the manufacturer’s ins
The text continues in the official source.
