Beta
SOR-2010-201:en
SOR-2010-201:en — Passenger Automobile and Light Truck Greenhouse Gas Emission Regulations
Beta. Legal information, not legal advice. LEGALDIGM is not a law firm. Check the official source for the current text.
Analyze this law with AI1 (1) The following definitions apply in these Regulations.
Act means the Canadian Environmental Protection Act, 1999. (Loi)
advanced technology vehicle means an electric vehicle, a plug-in hybrid electric vehicle or a fuel cell vehicle. (véhicule à technologie de pointe)
alcohol dual fuel vehicle means a vehicle that
(a) is designed to operate either on
(i) alcohol fuel or gasoline, or
(ii) alcohol fuel or diesel fuel;
(b) yields equal or greater energy efficiency, calculated in accordance with section 510(g)(1) of Title 40, chapter I, part 600, subpart F, of the CFR, while operating on alcohol fuel as it does while operating on gasoline or diesel fuel; and
(c) meets or exceeds the minimum driving range set out in section 5(a) of Title 49, subtitle B, chapter V, part 538, of the CFR. (véhicule à alcool à double carburant)
alcohol fuel means a fuel mixture containing 85% or more by volume of methanol, ethanol, or other alcohols. (alcool carburant)
approach angle means the smallest angle, in a plan side view of a vehicle, formed by the level surface on which the vehicle is standing and a line tangent to the front tire static loaded radius arc and touching the underside of the vehicle forward of the front tire. (angle d’approche)
automobile means any four-wheeled self-propelled vehicle that is designed for use on highways and that has a GVWR of less than 4 536 kg (10,000 pounds), except
(a) a vehicle manufactured in different stages by two or more manufacturers, if no intermediate or final-stage manufacturer of that vehicle manufactures more than 10,000 multistage vehicles per year; and
(b) a work truck. (automobile)
axle clearance means the vertical distance from the level surface on which a vehicle is standing to the lowest point on the axle differential of the vehicle. (garde au sol sous les essieux)
break-over angle means the supplement of the largest angle, in the plan side view of a vehicle, that can be formed by two lines tangent to the front and rear static loaded radii arcs and intersecting at a point on the underside of the vehicle. (angle de rampe)
cargo box length at the floor means the longitudinal distance between the inside front of the cargo box and the inside of the closed endgate as measured at the surface of the cargo box floor along the vehicle’s centreline. (longueur de caisse au plancher)
cargo box length at the top of the body means the longitudinal distance between the inside front of the cargo box and the inside of the closed endgate as measured at the height of the top of the cargo box along the vehicle’s centreline. (longueur de caisse au sommet de la carrosserie)
cargo box width means the width of the cargo box as measured at the cargo box’s narrowest point between the wheelhouses. (largeur de la caisse de chargement)
car line
CFR means the Code of Federal Regulations of the United States as amended from time to time. (CFR)
CO2 means carbon dioxide. (CO2)
curb weight means, at the manufacturer’s choice, the actual or manufacturer’s estimated weight of a vehicle in operational status with all standard equipment and weight of fuel at nominal tank capacity and the weight of optional equipment. (masse en état de marche)
departure angle means the smallest angle, in a plan side view of a vehicle, formed by the level surface on which the vehicle is standing and a line tangent to the rear tire static loaded radius arc and touching the underside of the vehicle rearward of the rear tire. (angle de sortie)
electric vehicle means a vehicle that
(a) conforms to the emission standards of bin 1 set out in a horizontal row in Table S04-1 in section 1811 of Title 40, chapter I, subchapter C, part 86, subpart S, of the CFR;
(b) is powered solely by an electric motor drawing current from a rechargeable energy storage system, provided that recharge energy can be drawn from a source that is not on-board the vehicle; and
(c) does not have an on-board combustion engine-generator system as a means of providing electrical energy. (véhicule électrique)
emergency vehicle means a vehicle that is manufactured primarily for use as an ambulance or a police vehicle. (véhicule d’urgence)
EPA means the United States Environmental Protection Agency. (EPA)
EPA certificate means a certificate of conformity to U.S. federal standards issued by the EPA. (certificat de l’EPA)
fire fighting vehicle means a passenger automobile or light truck that is designed to be used under emergency conditions to transport personnel and equipment and to support the suppression of fires and the mitigation of other emergency situations. (véhicule d’incendie)
footprint means the result of the product of the average width (measured in inches and rounded to the nearest tenth of an inch) of the lateral distance between the centrelines of the front and rear base tires at ground, multiplied by the longitudinal distance between the front and rear wheel centrelines (measured in inches and rounded to the nearest tenth of an inch), divided by 144 and rounded to the nearest tenth of a square foot. (empreinte)
fuel cell vehicle means an electric vehicle propelled solely by an electric motor, the energy for the motor being supplied by an electrochemical cell that produces electricity without fuel combustion. (véhicule à pile à combustible)
full-size pick-up truck means a light truck that has a passenger compartment and a cargo box without a permanently fixed roof and that meets the following specifications:
(a) a cargo box width of 121.9 cm (48 inches) or more;
(b) a cargo box length of 152.4 cm (60 inches) or more, which length corresponds to the lesser of the cargo box length at the top of the body and the cargo box length at the floor; and
(c) a towing capability of 2 267 kg (5,000 pounds) or more or a payload capability of 771 kg (1,700 pounds) or more. (grosse camionnette)
GCWR means the gross combination weight rating specified by a manufacturer as the maximum combined weight of a towing vehicle, its passengers and its cargo, plus the weight of the trailer and its cargo. (PNBC)
GVWR means the gross vehicle weight rating specified by a manufacturer as the maximum design loaded weight of a single vehicle. (PNBV)
hybrid electric vehicle means a vehicle that is powered by an electric motor drawing current from a rechargeable energy storage system from an on-board electric source and by an internal combustion engine or heat engine. (véhicule électrique hybride)
light truck means an automobile
(a) that has four-wheel drive or a GVWR of more than 2 722 kg (6,000 pounds) and that has at least four of the following characteristics calculated when the automobile is at curb weight, on a level surface, with the front wheels parallel to the automobile’s longitudinal centreline and the tires inflated to the manufacturer’s recommended pressure:
(i) approach angle of not less than 28 degrees,
(ii) break-over angle of not less than 14 degrees,
(iii) departure angle of not less than 20 degrees,
(iv) running clearance of not less than 20 centimetres,
(v) front and rear axle clearances of not less than 18 centimetres; or
(b) that is designed to perform at least one of the following functions:
(i) transport more than 10 persons,
(ii) provide temporary living quarters,
(iii) transport property on an open bed,
(iv) provide greater cargo-carrying than passenger-carrying volume, the cargo-carrying volume of a vehicle sold with a second-row seat being determined with that seat installed, regardless of whether or not the manufacturer has described that seat as optional,
(v) permit expanded use of the automobile for cargo-carrying purposes through the removal or stowing of seats to create a flat surface extending from the forwardmost point of installation of those seats to the rear of the automobile’s interior, with automobiles of the 2012 and subsequent model years being equipped with at least three rows of designated seating positions as standard equipment. (camion léger)
mild hybrid electric technology means a technology that includes automatic start/stop capability and regenerative braking capability, and with which the recovered energy is at least 15% but less than 65% of the total braking energy, as determined in accordance with the test procedure set out in section 116(d) of Title 40, chapter I, part 600, subpart B, of the CFR. (technologie électrique hybride légère)
model type means passenger automobiles or light trucks that have the same combination of car line, transmission class and basic engine or basic electric motor. (type de modèle)
model year means the year, as determined under section 4, that is used by a manufacturer to designate a model of vehicle. (année de modèle)
natural gas dual fuel vehicle means a vehicle that
(a) is designed to operate either on
(i) natural gas or gasoline, or
(ii) natural gas or diesel fuel;
(b) yields equal or greater energy efficiency, calculated in accordance with section 510(g)(1) of Title 40, chapter I, part 600, subpart F, of the CFR, while operating on natural gas as it does while operating on gasoline or diesel fuel; and
(c) meets or exceeds the minimum driving range set out in section 5(a) of Title 49, subtitle B, chapter V, part 538, of the CFR. (véhicule à gaz naturel à double carburant)
natural gas vehicle means a vehicle designed to operate exclusively on natural gas. (véhicule au gaz naturel)
nominal tank capacity means the volume of the fuel tank specified by the manufacturer to the nearest three eighths of a litre (one tenth of a U.S. gallon). (capacité nominale du réservoir à carburant)
passenger automobile means any automobile, other than a light truck, that is designed for use in the transportation of not more than 10 persons. (automobile à passagers)
payload capability means the difference between the GVWR and curb weight of a vehicle. (charge utile)
plug-in hybrid electric vehicle means a hybrid electric vehicle that has the capability to recharge its energy storage system from an electric source that is not on board the vehicle. (véhicule électrique hybride rechargeable)
running clearance means the vertical distance from the level surface on which a vehicle is standing to the lowest point on the vehicle, excluding any point on a component that forms part of the vehicle’s unsprung weight. (jeu fonctionnel)
static loaded radius arc means a portion of a circle whose centre is the centre of a standard tire-rim combination of a vehicle and whose radius is the distance from that centre to the level surface on which the vehicle is standing, measured with the vehicle at curb weight, the wheel parallel to the vehicle’s longitudinal centreline and the tire inflated to the manufacturer’s recommended pressure. (arc du rayon sous charge)
strong hybrid electric technology means a technology that includes automatic start/stop capability and regenerative braking capability, and with which the recovered energy is at least 65% of the total braking energy, as determined in accordance with the test procedure set out in section 116(d) of Title 40, chapter I, part 600, subpart B, of the CFR. (technologie électrique hybride complète)
temporary living quarters means a space in the interior of an automobile that includes sleeping surfaces and household conveniences and in which people may temporarily live. (abri provisoire)
towing capability means the difference between the GCWR and GVWR of a vehicle. (capacité de remorquage)
transmission class
useful life means the period of time or use in respect of which an emission standard applies to a vehicle, as follows
(a) in the case of a passenger automobile or light truck other than a medium-duty passenger vehicle as defined in subsection 1(1) of the On-Road Vehicle and Engine Emission Regulations — 10 years or 120,000 miles; whichever occurs first; or
(b) in the case of a light truck that is a medium-duty passenger vehicle as defined in subsection 1(1) of the On-Road Vehicle and Engine Emission Regulations — 11 years or 120,000 miles; whichever occurs first. (durée de vie utile)
work truck means a vehicle that has a GVWR of more than 3 856 kg (8,500 pounds) and less than or equal to 4 536 kg (10,000 pounds) and does not include a medium-duty passenger vehicle as defined in subsection 1(1) of the On-Road Vehicle and Engine Emission Regulations. (camion de travail)
zero-emission vehicle means an automobile that is an electric vehicle, a plug-in hybrid electric vehicle or a fuel cell vehicle. (véhicule zéro émission )
(2)
(3) Standards that are incorporated by reference in these Regulations from the CFR are those expressly set out in the CFR and must be read as excluding
(a) references to the EPA or the Administrator of the EPA exercising discretion in any way;
(b) references to the Secretary of Transportation exercising discretion in any way;
(c) alternative standards related to fleet averages, other averages, emission credits, small volume manufacturers, or financial hardship; and
(d) standards or evidence of conformity of any authority other than the EPA.
1.1 For the purposes of these Regulations, a vehicle of a specific model year that is sold in Canada is considered to be sold concurrently in Canada and in the United States if a vehicle of that model year that belongs to the same test group is offered for sale in the United States during the 365 days preceding
(a) in the case of a vehicle that is imported into Canada, the day on which the vehicle is imported; and
(b) in the case of a vehicle that is manufactured in Canada,
(i) the day on which the national emissions mark is applied to the vehicle, if known, or
(ii) if the day referred to in subparagraph (i) is not known, the day on which the main assembly of the vehicle was completed.
2 The purpose of these Regulations is to reduce greenhouse gas emissions from passenger automobiles and light trucks by establishing
(a) emission standards and test procedures that are aligned with the federal requirements of the United States; and
(b) requirements that, beginning in model year 2026, will incrementally lead to all new passenger automobiles and light trucks being zero-emission vehicles as of model year 2035.
3 These Regulations set out
(a) prescribed classes of vehicles for the purposes of section 149 of the Act;
(b) requirements respecting the conformity of passenger automobiles and light trucks with greenhouse gas emission standards for the purposes of section 153 of the Act;
(c) requirements respecting the conformity of fleets of passenger automobiles and light trucks with greenhouse gas emission standards and other requirements for carrying out the purposes of Division 5 of Part 7 of the Act;
(d) a credit system for the purposes of section 162 of the Act;
(e) requirements respecting the conformity of combined fleets, as defined in subsection 30.1(1), with requirements for zero-emission vehicles; and
(f) a system of compliance units related to zero-emission vehicles.
4 (1) A year that is used by a manufacturer as a model year must
(a) if the period of production of a model of vehicle does not include January 1 of a calendar year, correspond to the calendar year during which the period of production falls; or
(b) if the period of production of a model of vehicle includes January 1 of a calendar year, correspond to that calendar year.
(2) The period of production of a model of vehicle must include only one January 1.
5 (1) In these Regulations, subject to subsection (2), the following classes of vehicles are prescribed for the purposes of the definition vehicle in section 149 of the Act:
(a) passenger automobiles; and
(b) light trucks.
(2) The prescribed classes of vehicles referred to in subsection (1) do not include any vehicle that is being exported and that is accompanied by written evidence establishing that it will not be sold or used in Canada.
(3) For the purposes of section 152 of the Act, the prescribed vehicles are the vehicles referred to in subsection (1) for which the main assembly is completed in Canada, except any vehicle that will be used in Canada solely for purposes of exhibition, demonstration, evaluation or testing.
6 (1) Any company that intends to apply the national emissions mark set out in Schedule 2 to the On-Road Vehicle and Engine Emission Regulations to a vehicle must apply to the Minister for authorization in accordance with subsection 7(2) of those Regulations.
(2) Subsection (1) does not apply to any company that, since September 23, 2010 or an earlier date, has been authorized to apply the national emissions mark to a vehicle under the On-Road Vehicle and Engine Emission Regulations.
7 A company that applies a national emissions mark to a vehicle must comply with section 8 of the On-Road Vehicle and Engine Emission Regulations.
8 (1) In subsection 10(2) and sections 13 to 40, fleet refers to
(a) all passenger automobiles or all light trucks of a specific model year that a company manufactures in Canada or imports into Canada for the purpose of sale of those vehicles to the first retail purchaser; or
(b) if a company makes an election under section 24, all passenger automobiles or all light trucks of a specific model year that a company manufactures in Canada or imports into Canada for the purpose of sale of those vehicles to the first retail purchaser that have not been included in the temporary optional fleet created under section 24 for that model year.
(2) Despite subsection (1), a company may, for the purposes of sections 13 to 40, elect to exclude from its fleets and its temporary optional fleets any of the following:
(a) the passenger automobiles or light trucks that it manufactures and that will be used in Canada solely for the purposes of exhibition, demonstration, evaluation or testing, if it reports its election to exclude those vehicles in its end of model year report;
(b) the passenger automobiles or light trucks that it imports into Canada solely for the purposes of exhibition, demonstration, evaluation or testing, if it makes a declaration in accordance with section 41 of the On-Road Vehicle and Engine Emission Regulations and reports its election to exclude those vehicles in its end of model year report.
(3) A company’s fleet of passenger automobiles or light trucks of the 2011 model year does not include vehicles that were manufactured before September 23, 2010, unless the company elects to include all of its passenger automobiles or light trucks of the 2011 model year in the fleet in question and reports that election in its end of model year report.
(4) Despite subsection (1), a company may, for the purposes of sections 10, 13 to 31 and 33 to 40, elect to exclude emergency vehicles from its fleets and its temporary optional fleets of passenger automobiles and light trucks of the model year corresponding to the year during which this subsection comes into force and any subsequent model year, if it reports that election in its end of model year report for that model year.
9 (1) An emission control system that is installed in a vehicle to enable it to conform to the standards set out in these Regulations must be in conformity with subsection 11(1) of the On-Road Vehicle and Engine Emission Regulations.
(2) A vehicle must not be equipped with a defeat device.
(3) Subsections 11(3) and (4) of the On-Road Vehicle and Engine Emission Regulations apply, except that the test procedures in question are the ones set out in section 11.
(4) Despite subsection (2), an emergency vehicle or fire fighting vehicle may be equipped with a defeat device if the device is one that is activated during emergency response operations to maintain speed, torque or power in either of the following circumstances:
(a) the emission control system is in an abnormal state; or
(b) the device acts to maintain the emission control system in a normal state.
10 (1) Subject to subsection (2) and section 12, passenger automobiles and light trucks of the 2012 model year or a subsequent model year must conform to the following exhaust emission standards for nitrous oxide (N2O) and methane (CH4) for the applicable model year:
(a) the standards for nitrous oxide (N2O) and methane (CH4) set out in section 1818(f)(1) of Title 40, chapter I, subchapter C, part 86, subpart S, of the CFR;
(b) the standards for nitrous oxide (N2O) set out in section 1818(f)(1) of Title 40, chapter I, subchapter C, part 86, subpart S, of the CFR and the alternative standards for methane (CH4) determined in accordance with section 1818(f)(3) of that subpart;
(c) the alternative standards for nitrous oxide (N2O) determined in accordance with section 1818(f)(3) of Title 40, chapter I, subchapter C, part 86, subpart S, of the CFR and the standards for methane (CH4) set out in section 1818(f)(1) of that subpart; or
(d) the alternative standards for nitrous oxide (N2O) and methane (CH4) determined in accordance with section 1818(f)(3) of Title 40, chapter I, subchapter C, part 86, subpart S, of the CFR.
(2) Instead of complying with subsection (1), a company may elect to include the exhaust emissions of nitrous oxide (N2O) and methane (CH4) of its passenger automobiles and light trucks of a model year when calculating their carbon-related exhaust emission value as set out in subsection 18.1(2) in respect of each of its fleets of that model year.
(3) A company that makes an election under subsection (2) must ensure that it applies to all models of passenger automobiles and light trucks that it manufactures or imports.
11 The standards referred to in section 10 are the certification and in-use standards for the applicable useful life, taking into account the test procedures, fuels and calculation methods set out for those standards in subpart B of Title 40, chapter I, subchapter C, part 86 of the CFR and in subpart B of Title 40, chapter I, subchapter Q, part 600, of the CFR.
12 (1) Every vehicle of a specific model year that is covered by an EPA certificate and that bears the label referred to in paragraph 36(1)(d) must conform to, instead of the standards set out in sections 9 and 10, the certification and in-use standards referred to in the EPA certificate.
(2) For the purposes of subsection 153(3) of the Act, the provisions of the CFR that are applicable to a vehicle referred to in subsection (1), pursuant to the EPA certificate, correspond to the certification and in-use standards referred to in subsection (1).
(3) For the purposes of subsection 153(3) of the Act, the EPA is the prescribed agency.
13 Subject to sections 14, 20 and 21, a company must ensure that the fleet average CO2 equivalent emission value for each fleet of its passenger automobiles and fleet of its light trucks of the 2011 and subsequent model years does not exceed the applicable fleet average CO2 equivalent emission standard for the model year in question.
14 (1) A company that manufactured or imported at least one passenger automobile or light truck but in total not more than 749 passenger automobiles and light trucks of either the 2008 or 2009 model years for sale in Canada is not subject to sections 13 and 17 to 20 for vehicles of the 2012 model year or a subsequent model year if
(a) the average number of passenger automobiles and light trucks that were manufactured or imported by the company for sale in Canada is less than 750 for the three consecutive model years preceding the model year that is one year before the model year in question; and
(b) the company submits a declaration as set out in section 35.
(1.1) A company that did not manufacture or import any passenger automobiles or light trucks of the 2011 to 2016 model years for sale in Canada during the 2010 to 2016 calendar years is not subject to sections 13 and 17 to 20 for vehicles of the 2017 model year or a subsequent model year if the company submits a declaration as set out in section 35 and
(a) in the case of the first model year for which the company manufactures or imports passenger automobiles or light trucks for sale in Canada, the company manufactures or imports in total less than 750 passenger automobiles and light trucks;
(b) in the case of the second model year for which the company manufactures or imports passenger automobiles or light trucks for sale in Canada, the company manufactures or imports in total less than 750 passenger automobiles and light trucks;
(c) in the case of the third model year for which the company manufactures or imports passenger automobiles or light trucks for sale in Canada, the company manufactures or imports in total less than 750 passenger automobiles and light trucks; and
(d) in the case of any subsequent model year, the average number of passenger automobiles and light trucks that are or were manufactured or imported by the company for sale in Canada for that model year and for the two preceding model years is less than 750.
(2) If, for the three consecutive model years preceding the model year in question, the average number of passenger automobiles and light trucks that were manufactured or imported by a company for sale in Canada is equal to or greater than 750 — other than by reason of the company purchasing another company — the company becomes subject to sections 13, 17 to 20 and 33 for its passenger automobiles and light trucks of the following model year:
(a) if that average number is less than 7,500, that of the second model year after the last model year used to establish the average number; or
(b) if that average number is equal to or greater than 7,500, that of the model year after the last model year used to establish the average number.
15 (1) If any of the calculations in these Regulations, except for those in paragraphs 17(4)(b) and (5)(b), subsections 17(6) and (7) and 18.1(1), (5) and (10), sections 18.2 and 18.3 and subsections 18.4(1), 30.13(1), 30.14(3) and 30.21(2) and (3), results in a number that is not a whole number, the number must be rounded to the nearest whole number in accordance with section 6 of the ASTM International method ASTM E29-93a, entitled Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications.
(2) If any of the calculations in paragraphs 17(4)(b) and (5)(b), subsections 17(6) and (7) and 18.1(1), (5) and (10), sections 18.2 and 18.3 and subsection 18.4(1) results in a number that is not a whole number, the number must be rounded to the nearest tenth of a unit in accordance with section 6 of that method.
(3) If any of the calculations in subsections 30.13(1), 30.14(3) and 30.21(2) and (3) results in a number that is not a whole number, the number must be rounded to the nearest ten-thousandth of a unit in accordance with section 6 of that method.
16 (1) A company must calculate the fleet average CO2 equivalent emission standard, expressed in grams of CO2 equivalent per mile, in respect of its fleet of passenger automobiles and its fleet of light trucks of the 2011 model year, by dividing 8,887 by the following:
(a) in the case of passenger automobiles, the manufacturer specific passenger automobile fuel economy level for the 2011 model year determined in accordance with section 5(b) of Title 49, subtitle B, chapter V, part 531, of the CFR, applicable to that model year; and
(b) in the case of light trucks, the manufacturer specific light truck fuel economy level for the 2011 model year determined in accordance with section 5(a) of Title 49, subtitle B, chapter V, part 533, of the CFR, applicable to that model year.
(2) For the purposes of subsection (1), the equation in Figure 1 set out in section 5 of parts 531 and 533 of Title 49, subtitle B, chapter V, of the CFR, is modified as follows:
(a) “N” is the total number of passenger automobiles or light trucks in the fleet;
(b) “Ni” is the number of passenger automobiles or light trucks in each group “i” in the fleet; and
(c) “i” is a group of passenger automobiles or light trucks of the same model type and that have the same footprint.
17 (1) For the purposes of this section, passenger automobiles or light trucks of the same model type and that have the same footprint constitute a group.
(2)
(3) Subject to sections 24 and 28.1, a company must calculate the fleet average CO2 equivalent emission standard for its fleet of passenger automobiles and its fleet of light trucks of the 2012 model year and subsequent model years in accordance with the following formula:
is the CO2 emission target value for each group of passenger automobiles or light trucks, determined in accordance with subsection (4), (5), (6) or (7), as the case may be, and expressed in grams of CO2 per mile;
is the number of passenger automobiles or light trucks in the group in question; and
is the total number of passenger automobiles or light trucks in the fleet.
(4) For fleets of the 2012 to 2016 models years, the CO2 emission target value applicable to a group of passenger automobiles of a given model year corresponds to the following:
(a) in the case of each group with a footprint that is less than or equal to 3.8 m2 (41 square feet), the CO2 emission target value is as set out in the following table for the model year in question:
(b) in the case of each group with a footprint that is greater than 3.8 m2 (41 square feet) and less than or equal to 5.2 m2 (56 square feet), the CO2 emission target value is to be calculated using the following formula:
is the footprint of the group, expressed in square feet, and
is the value set out in the following table for the model year in question:
(c) in the case of each group with a footprint that is greater than 5.2 m2 (56 square feet), the CO2 emission target value is as set out in the following table for the model year in question:
(5) For fleets of the 2012 to 2016 model years, the CO2 emission target value applicable to a group of light trucks of a given model year corresponds to the following:
(a) in the case of each group with a footprint that is less than or equal to 3.8 m2 (41 square feet), the CO2 emission target value is as set out in the following table for the model year in question:
(b) in the case of each group with a footprint that is greater than 3.8 m2 (41 square feet) and less than or equal to 6.1 m2 (66 square feet), the CO2 emission target value is to be calculated using the following formula:
is the footprint of the group, expressed in square feet, and
is the value set out in the following table for the model year in question:
(c) in the case of each group with a footprint that is greater than 6.1 m2 (66 square feet), the CO2 emission target value is as set out in the following table for the model year in question:
(6) The CO2 emission target value applicable to a given group of passenger automobiles of the 2017 model year and subsequent model years corresponds to the value determined for that group in accordance with section 1818(c)(2)(i) of Title 40, chapter I, subchapter C, part 86, subpart S, of the CFR.
(7) The CO2 emission target value applicable to a given group of light trucks of the 2017 model year and subsequent model years corresponds to the value determined for that group in accordance with section 1818(c)(3)(i) of Title 40, chapter I, subchapter C, part 86, subpart S, of the CFR.
(8) Despite the definition CFR in subsection 1(1), the provisions of the CFR referred to in subsections (6) and (7) are as they read on February 28, 2022.
18 A company must calculate the fleet average CO2 equivalent emission value for its fleet of passenger automobiles and its fleet of light trucks of the 2011 model year and subsequent model years in accordance with the following formula:
is the fleet average carbon-related exhaust emission value for each fleet, calculated in accordance with subsections 18.1(1) and (2), taking into account subsections 18.1(6) and (7);
is the allowance for the reduction of air conditioning refrigerant leakage, calculated in accordance with subsection 18.2(1);
is the allowance for the improvement of air conditioning system efficiency, calculated in accordance with subsection 18.2(2);
is the allowance for the use of innovative technologies that result in a measurable CO2 emission reduction, which corresponds to the sum of the allowances calculated in accordance with subsections 18.3(1), (3) or (3.1), and (5); and
is the CO2 allowance for full-size pick-up trucks, calculated in accordance with subsection 18.4(1).
18.1 (1) The fleet average carbon-related exhaust emission value for the 2011 model year, expressed in grams of CO2 equivalent per mile, is calculated by dividing 8,887 by the company’s fleet average fuel economy for that model year calculated in accordance with the following formula:
is the fuel economy level for each model type, expressed in miles per gallon, determined in accordance with the following provisions, taking into account subsection 19(2):
in the case of advanced technology vehicles, the provisions of section 208 of Title 40, chapter I, part 600, subpart C, of the CFR, for the model year in question, or
in all other cases, the provisions of section 510(c)(2) of Title 40, chapter I, part 600, subpart F, of the CFR, for the model year in question;
is the number of vehicles of the model type in question in the fleet; and
is the total number of vehicles in the fleet.
(2) Subject to subsections (8) and (10), a company must calculate the fleet average carbon-related exhaust emission value for each of its fleets of the 2012 model year and subsequent model years using the following formula:
is the following carbon-related exhaust emission value for each model type and includes, if an election is made under subsection 10(2), the exhaust emission for nitrous oxide (N2O) and methane (CH4):
in the case of electric vehicles and fuel cell vehicles, 0 grams of CO2 equivalent per mile,
in the case of plug-in hybrid electric vehicles, the value determined in accordance with section 113(n)(2) of Title 40, chapter I, part 600, subpart B, of the CFR for the model year in question, taking into account subsection 19(2) and the following clarifications, and expressed in grams of CO2 equivalent per mile:
the value in respect of exhaust emissions is determined in accordance with section 510(j)(2) of Title 40, chapter I, part 600, subpart F, of the CFR, and
the equivalent value in respect of the electricity grid for the electricity that is used to recharge the energy storage system is equal to 0 grams of CO2 equivalent per mile, or
in all other cases, the value determined in accordance with section 510(j)(2) of Title 40, chapter I, part 600, subpart F, of the CFR, for the model year in question, taking into account subsection 19(2), and expressed in grams of CO2 equivalent per mile;
is the number of vehicles of the model type in question in the fleet; and
is the total number of vehicles in the fleet.
(3) When calculating the fleet average carbon-related exhaust emission value in accordance with subsections (1) and (2) for fleets of the 2011 to 2016 model years, a company may, for the purposes of the descriptions of B and C in subsections (1) and (2), elect to multiply the number of advanced technology vehicles in its fleet by 1.2, if the company reports that election and indicates the number of credits obtained as a result of that election in its end of model year report.
(4) Subject to subsection (5), when calculating the fleet average carbon-related exhaust emission value in accordance with subsection (2) for fleets of the 2017 to 2024 model years, a company may, for the purposes of the descriptions of B and C in subsection (2), elect to multiply the number of advanced technology vehicles, natural gas vehicles or natural gas dual fuel vehicles in its fleet by the number set out in the following table in respect of that type of vehicle for the model year in question, if the company reports that election and indicates the number of credits obtained as a result of that election and the number of vehicles in question in its end of model year report.
(5) A company may make an election under subsection (4) in respect of a plug-in hybrid electric vehicle of the 2017 to 2024 model years only if the vehicle has an all-electric driving range equal to or greater than 16.4 km (10.2 miles) or an equivalent all-electric driving range equal to or greater than 16.4 km (10.2 miles). The all-electric driving range and the equivalent all-electric driving range are determined in accordance with section 1866(b)(2) of Title 40, chapter I, subchapter C, part 86, subpart S, of the CFR.
(6) For the purposes of subsections (1) and (2) for fleets of the 2011 to 2015 model years, and for the purposes of section 29 for fleets of the 2008 to 2010 model years, if the fleet contains alcohol dual fuel vehicles or natural gas dual fuel vehicles, the fleet average carbon-related exhaust emission value is the greater of
(a) the fleet average carbon-related exhaust emission value calculated in accordance with subsections (1) and (2), and
(b) the fleet average carbon-related exhaust emission value calculated in accordance with subsections (1) and (2) with the assumption that all alcohol dual fuel vehicles and natural gas dual fuel vehicles operate exclusively on gasoline or diesel fuel, minus the applicable limit set out in section 510(i) of Title 40, chapter I, part 600, subpart F, of the CFR.
(7) For the purposes of section 510(j)(2)(vi) of Title 40, chapter I, part 600, subpart F, of the CFR, a company may use an alternative value for the weighting factor “F” if the company provides the Minister with evidence demonstrating that the alternative value is more representative of its fleet.
(8) For the purposes of paragraphs (a) and (b) of the description of A in subsection (2), a company must replace the carbon-related exhaust emission value, referred to in the description of A in that subsection, with the value determined under subsection (10) for all of the electric vehicles and plug-in hybrid electric vehicles in its fleets of the model year corresponding to the year during which this subsection comes into force, and subsequent model years until the 2016 model year, that are in excess of the following applicable maximum number of advanced technology vehicles:
(a) 30,000 vehicles, in the case of a company that manufactured or imported less than 3,750 advanced technology vehicles of the 2012 model year for sale in Canada and that has already included 30,000 advanced technology vehicles in its fleets of the 2011 to 2016 model years, or in its fleets of the 2008 to 2016 model years, if the company obtained early action credits in respect of its fleets of the 2008 to 2010 model years; or
(b) 45,000 vehicles, in the case of a company that manufactured or imported 3,750 or more advanced technology vehicles of the 2012 model year for sale in Canada and that has already included 45,000 advanced technology vehicles in its fleets of the 2011 to 2016 model years, or in its fleets of the 2008 to 2016 model years, if the company obtained early action credits in respect of its fleets of the 2008 to 2010 model years.
(9)
(10) For any electric vehicles and plug-in hybrid electric vehicles that are in excess of the applicable maximum number, a company must determine the carbon-related exhaust emission value for the model year in question, taking into account subsection 19(2) and expressing the result in grams of CO2 equivalent per mile, in accordance with
(a) in the case of electric vehicles, section 113(n)(1) of Title 40, chapter I, part 600, subpart B, of the CFR — excluding the measure for the limited number of vehicles referred to in the description of CREE — except that the description of AVGUSUP in that section is equal to 0.210; and
(b) in the case of plug-in hybrid electric vehicles, section 113(n)(2) of Title 40, chapter I, part 600, subpart B, of the CFR, taking into account the following clarifications:
(i) the value in respect of exhaust emissions is determined in accordance with section 510(j)(2) of Title 40, chapter I, part 600, subpart F, of the CFR, and
(ii) the equivalent value in respect of the electricity grid for the electricity that is used to recharge the energy storage system is determined in accordance with section 113(n)(1) of Title 40, chapter I, part 600, subpart B, of the CFR — excluding the measure for the limited number of vehicles referred to in the description of CREE — except that the description of AVGUSUP in that section is equal to 0.210.
(11) For the purposes of subsection (8), a company must count its fuel cell vehicles before counting the other advanced technology vehicles.
18.2 (1) A company may elect to calculate, using the following formula, an allowance for the use, in its fleet of passenger automobiles or light trucks, of air conditioning systems that incorporate technologies designed to reduce air conditioning refrigerant leakage:
is the CO2 equivalent leakage reduction for each air conditioning system in the fleet that incorporates those technologies, determined in accordance with section 1867 of Title 40, chapter I, subchapter C, part 86, of the CFR and expressed in grams of CO2 equivalent per mile;
is the number of passenger automobiles or light trucks in the fleet that are equipped with the air conditioning system; and
is the total number of passenger automobiles or light trucks in the fleet.
(2) A company may elect to calculate, using the following formula, an allowance for the use, in its fleet of passenger automobiles or light trucks, of air conditioning systems that incorporate technologies designed to reduce air-conditioning-related CO2 emissions by improving air conditioning system efficiency:
is the air conditioning efficiency allowance for each air conditioning system in the fleet that incorporates those technologies, determined in accordance with the provisions relating to credits in section 1868 of Title 40, chapter I, subchapter C, part 86, of the CFR and expressed in grams of CO2 per mile;
is the number of passenger automobiles or light trucks in the fleet that are equipped with the air conditioning system; and
is the total number of passenger automobiles or light trucks in the fleet.
18.3 (1) Subject to subsections (3) and (3.1), a company may elect to calculate an allowance for the use, in its fleet of the 2014 model year and subsequent model years, of innovative technologies that result in a measurable CO2 emission reduction and that are referred to in section 1869(b)(1) of Title 40, chapter I, subchapter C, part 86, subpart S, of the CFR, using the following formula:
is the allowance for each of those technologies that is used in the fleet, determined in accordance with section 1869(b)(1) of Title 40, chapter I, subchapter C, part 86, of the CFR and expressed in grams of CO2 per mile;
is the number of passenger automobiles or light trucks in the fleet that are equipped with the innovative technology; and
is the total number of passenger automobiles or light trucks in the fleet.
(2) Instead of determining the allowance for each innovative technology that is used in the fleet in accordance with the description of A in subsection (1), a company may
(a) determine that allowance in accordance with the provisions for the 5-cycle methodology set out in section 1869(c) of Title 40, chapter I, subchapter C, part 86, of the CFR, expressed in grams of CO2 per mile;
(b) use the credit value approved by the EPA for that technology under section 1869(e) of Title 40, chapter I, subchapter C, part 86, of the CFR, expressed in grams of CO2 per mile, if the company provides the Minister with evidence of that approval in its end of model year report; or
(c) determine that allowance in accordance with an alternative procedure, if the company provides the Minister with evidence demonstrating that the alternative procedure allows for a more accurate determination of the emission reduction attributable to the innovative technology and that the allowance determined in accordance with that procedure more accurately represents that emission reduction.
(3) If, for one of the 2014 to 2022 model years, the 2027 model year or any subsequent model year, the total of the allowances for innovative technologies that a company elects to determine, for a single vehicle, in accordance with the description of A in subsection (1) is greater than 10 grams of CO2 per mile, the company must calculate, using the following formula, the allowance for the use, in its fleet of passenger automobiles or light trucks of that model year, of innovative technologies that result in a measurable CO2 emission reduction and that are referred to in section 1869(b)(1) of Title 40, chapter I, subchapter C, part 86, subpart S, of the CFR:
is the allowance for each innovative technology for which an allowance is determined for the purposes of subsection (4);
is the number of passenger automobiles or light trucks that are equipped with the innovative technology that is used for the purposes of subsection (4); and
is the total number of passenger automobiles or light trucks in the fleet.
(3.1) If, for a model year of the 2023 to 2026 model years, the total of the allowances for innovative technologies that a company elects to determine, for a single vehicle, in accordance with the description of A in subsection (1) is greater than 15 grams of CO2 per mile, the company must calculate, using the formula set out in subsection (3), the allowance for the use, in its fleet of passenger automobiles or light trucks of that model year, of innovative technologies that result in a measurable CO2 emission reduction and that are referred to in section 1869(b)(1) of Title 40, chapter I, subchapter C, part 86, subpart S, of the CFR.
(4) For the purposes of subsections (3) and (3.1), the company must perform the following calculation and ensure that the result does not exceed 10 or 15 grams of CO2 per mile, respectively:
is the allowance for each innovative technology that is used in the fleet and that the company decides to take into account, determined in accordance with subsection (1);
is the number of passenger automobiles in the fleet that are equipped with the innovative technology in question and that the company decides to take into account;
is the number of light trucks in the fleet that are equipped with the innovative technology in question and that the company decides to take into account;
is the total number of passenger automobiles in the fleet; and
is the total number of light trucks in the fleet.
(5) A company may elect to calculate, using the following formula, an allowance for the use, in its fleet of passenger automobiles or light trucks, of innovative technologies — other than those referred to in subsection (1) — that result in a measurable CO2 emission reduction:
is the allowance for each innovative technology that is used in the fleet, determined in accordance with the provisions for the 5-cycle methodology set out in section 1869(c) of Title 40, chapter I, subchapter C, part 86, of the CFR and expressed in grams of CO2 per mile;
is the number of passenger automobiles or light trucks in the fleet that are equipped with the innovative technology; and
is the total number of passenger automobiles or light trucks in the fleet.
(6) If the 5-cycle methodology referred to in subsection (5) cannot adequately measure the emission reduction attributable to an innovative technology, a company may, instead of determining the allowance for the innovative technology in accordance with the description of A in subsection (5),
(a) use the credit value approved by the EPA for that technology under section 1869(e) of Title 40, chapter I, subchapter C, part 86, of the CFR, expressed in grams of CO2 per mile, if the company provides the Minister with evidence of the EPA approval in its end of model year report; or
(b) determine that allowance in accordance with an alternative procedure, if the company provides the Minister with evidence demonstrating that the alternative procedure allows for a more accurate determination of the emission reduction attributable to the innovative technology and that the allowance determined in accordance with that procedure more accurately represent that emission reduction.
18.4 (1) Subject to subsections (2) to (4), a company may elect to calculate, using the following formula, a CO2 allowance for the presence, in its fleet, of full-size pick-up trucks equipped with hybrid electric technologies and of full-size pick-up trucks that achieve carbon-related exhaust emission values below the applicable target value:
is the allowance for the use of hybrid electric technologies, namely,
10 grams of CO2 per mile for mild hybrid electric technologies, or
20 grams of CO2 per mile for strong hybrid electric technologies;
is the number of full-size pick-up trucks in the fleet that are equipped with mild hybrid electric technologies or that are equipped with strong hybrid electric technologies, as the case may be;
is the allowance for full-size pick-up trucks that achieve a certain carbon-related exhaust emission value, namely,
10 grams of CO2 per mile for full-size pick-up trucks that achieve a carbon-related exhaust emission value that is less than or equal to their applicable target value, determined in accordance with subsection 17(7), multiplied by 0.85 and greater than their applicable target value multiplied by 0.8, or
20 grams of CO2 per mile for full-size pick-up trucks that achieve a carbon-related exhaust emission value that is less than or equal to their applicable target value, determined in accordance with subsection 17(7), multiplied by 0.8;
is the number of full-size pick-up trucks in the fleet that achieve a carbon-related exhaust emission value that is within the range referred to in paragraph (a) of the description of AR or that is less than or equal to their applicable target value, determined in accordance with subsection 17(7), multiplied by 0.8, as the case may be; and
is the total number of light trucks in the fleet.
(2) The allowance for the use of hybrid electric technologies referred to in paragraphs (a) and (b) of the description of AH in subsection (1) may be calculated in respect of full-size pick-up trucks of a model year only if the percentage in the fleet of full-size pick-up trucks of that model year that are equipped with those technologies is equal to or greater than the percentage for that model year set out in section 1870(a)(1) or (2), depending on the technology used, of Title 40, chapter I, subchapter C, part 86, subpart S, of the CFR. The allowance referred to in paragraph (a) of the description of AH may be calculated only for full-size pick-up trucks of the 2017 to 2021, 2023 and 2024 model years.
(2.1) If the percentage in the fleet of full-size pick-up trucks of a model year that are equipped with mild hybrid electric technologies or strong hybrid electric technologies is less than the percentage set out for the model year in, depending on the technology used, section 1870(a)(1) or (2) of Title 40, chapter I, subchapter C, part 86, of the CFR, the allowance for the use of hybrid electric technologies referred to in the description of AH in subsection (1) is 10 grams of CO2 per mile for those trucks, if the percentage in the fleet of full-size pick-up trucks that are equipped with either mild hybrid electric technologies or strong hybrid electric technologies is equal to or greater than the percentage referred to in section 1870(a)(3) of Title 40, chapter I, subchapter C, part 86, of the CFR. The allowance may be calculated only for full-size pick-up trucks of the 2017 to 2021 model years.
(3) The allowance for full-size pick-up trucks that achieve a carbon-related exhaust emission value referred to in paragraphs (a) and (b) of the description of AR in subsection (1) may be calculated in respect of full-size pick-up trucks of a model year only if the percentage in the fleet of full-size pick-up trucks of that model year that achieve such a value is equal to or greater than the percentage for that model year set out in section 1870(b)(1) or (2), depending on the emission performance achieved, of Title 40, chapter I, subchapter C, part 86, subpart S, of the CFR. The allowance referred to in paragraph (a) of the description of AR may be calculated only for full-size pick-up trucks of the 2017 to 2021, 2023 and 2024 model years.
(4) A company must not claim, in respect of the same pick-up truck, both the allowance referred to in the description of AH in subsection (1) and the allowance referred to in the description of AR in that subsection.
(5) A company that elects to multiply the number of advanced technology vehicles in its fleet in accordance with subsection 18.1(4) must not use the allowance referred to in the description of AR in subsection (1) for the same vehicle.
19 (1) The carbon-related exhaust emission value and the fuel economy level that are calculated in accordance with section 18.1 must be calculated taking into account the applicable test procedures, fuels and calculation methods set out in subpart B of Title 40, chapter I, subchapter C, part 86 and in subpart B of Title 40, chapter I, subchapter Q, part 600, of the CFR and taking into account any clarifications or additional information issued by the EPA, if the company keeps a copy of those clarifications or that additional information.
(2) When a company calculates the fleet average carbon-related exhaust emission value under section 18, the data and values used in the calculation must represent at least 90% of the total number of vehicles in the company’s fleet with respect to the configuration.
20 (1) For the purposes of subparagraph 162(1)(b)(i) of the Act, a company obtains CO2 equivalent emission credits if the fleet average CO2 equivalent emission value in respect of a fleet of passenger automobiles or a fleet of light trucks of a specific model year is lower than the fleet average CO2 equivalent emission standard for that fleet and model year and the company reports the credits in its end of model year report.
(2) A company incurs deficits if the fleet average CO2 equivalent emission value in respect of a fleet of passenger automobiles or a fleet of light trucks of a specific model year is higher than the fleet average CO2 equivalent emission standard for that fleet and model year.
(3) Subject to subsections (3.1) to (3.4), a company must calculate, using the following formula, the credits or deficits for each of its fleets:
is the number of credits, if the result is positive, or the number of deficits, if the result is negative, expressed in megagrams of CO2 equivalent;
is the fleet average CO2 equivalent emission standard calculated in accordance with section 16 or 17, as the case may be, expressed in grams per mile;
is the fleet average CO2 equivalent emission value calculated in accordance with section 18, expressed in grams per mile;
is the total number of passenger automobiles or light trucks in the fleet; and
is the assumed total mileage of the vehicles in question, namely,
(a) 195,264 miles for a fleet of passenger automobiles, or
(b) 225,865 miles for a fleet of light trucks.
(3.1) For each test group in respect of which a company uses, for any given model year, an alternative standard for nitrous oxide (N2O) under subsection 10(1) or 12(1), the company must use the following formula, expressing the result in megagrams of CO2 equivalent, and add the sum of the results for each test group to the number of credits or deficits calculated in accordance with subsection (3) for the fleet to which the test group belongs:
is the total number of passenger automobiles or light trucks in the test group;
is the exhaust emission standard for nitrous oxide (N2O) set out in section 1818(f)(1) of Title 40, chapter I, subchapter C, part 86, subpart S, of the CFR, for the applicable model year, expressed in grams per mile;
is the alternative exhaust emission standard for nitrous oxide (N2O) under subsection 10(1) or 12(1) to which the company certifies the test group, expressed in grams per mile; and
is the assumed total mileage of the vehicles in question, namely,
195,264 miles for a fleet of passenger automobiles, or
225,865 miles for a fleet of light trucks.
(3.2) For each test group in respect of which a company uses, for any given model year, an alternative standard for methane (CH4) under subsection 10(1) or 12(1), the company must use the following formula, expressing the result in megagrams of CO2 equivalent, and add the sum of the results for each test group to the number of credits or deficits calculated in accordance with subsection (3) for the fleet to which the test group belongs:
is the total number of passenger automobiles or light trucks in the test group;
is the exhaust emission standard for methane (CH4) set out in section 1818(f)(1) of Title 40, chapter I, subchapter C, part 86, subpart S, of the CFR, for the applicable model year, expressed in grams per mile;
is the alternative exhaust emission standard for methane (CH4) under subsection 10(1) or 12(1) to which the company certifies the test group, expressed in grams per mile; and
is the assumed total mileage of the vehicles in question, namely,
195,264 miles for a fleet of passenger automobiles, or
225,865 miles for a fleet of light trucks.
(3.3) A company may elect to calculate or recalculate its credits or deficits for any of its fleets of the 2017 to 2021 model years by making the election referred to in subsection 18.1(4) and by using the equation set out in subsection (3) but replacing the descriptions of A and C with the following:
is the adjusted fleet average CO2 equivalent emission standard, expressed in grams per mile, calculated in accordance with section 17 but, for the purposes of the descriptions of B and C in subsection 17(3), in the case of advanced technology vehicles, natural gas vehicles or natural gas dual fuel vehicles, the number of vehicles is multiplied by the number set out in the table to subsection 18.1(4) in respect of that type of vehicle for the model year in question;
is determined by the formula
is the number of passenger automobiles or light trucks in the fleet, excluding advanced technology vehicles, natural gas vehicles and natural gas dual fuel vehicles,
is the number of advanced technology vehicles, natural gas vehicles or natural gas dual fuel vehicles in the fleet, as the case may be, and
is the multiplier set out in the table to subsection 18.1(4) in respect of the type of vehicle for the model year in question.
(3.4) For the 2022 to 2024 model years, if a company makes the election under subsection 18.1(4), the descriptions of A and C in subsection (3) are replaced by the descriptions of A and C in subsection (3.3).
(4) Subject to subsection (4.1), a company obtains credits or incurs deficits for a specific fleet on the day on which the company submits the end of model year report for the model year in question.
(4.1) A company obtains credits or reduces its deficits for a specific fleet of the 2017 to 2021 model years if the report includes the following information in respect of that fleet:
(a) the number of credits or deficits calculated in accordance with subsection (3) and, as applicable, the number of credits or deficits calculated in accordance with subsection (3.3), as well as the difference between the results; and
(b) a statement that the company has elected to recalculate credits or deficits in accordance with subsection (3.3) and an indication of the number of additional credits, or the reduction in the number of deficits, obtained as a result of that election as well as the number of vehicles in question.
(5) Credits obtained for a fleet of passenger automobiles or light trucks of the 2011 to 2016 model years may be used in respect of any fleet of passenger automobiles or light trucks of any model year after the model year in respect of which the credits were obtained, until the 2021 model year, after which the credi
The text continues in the official source.
