LEGALDIGMLEGALDIGM
    ← Canada
    Beta
    SOR-2003-2:en

    SOR-2003-2:en — On-Road Vehicle and Engine Emission Regulations

    Beta. Legal information, not legal advice. LEGALDIGM is not a law firm. Check the official source for the current text.

    Analyze this law with AI
    1 (1) The following definitions apply in these Regulations. Act means the Canadian Environmental Protection Act, 1999. (Loi) adjusted loaded vehicle weight means the numerical average of a vehicle’s curb weight and its GVWR. (poids ajusté du véhicule chargé) approach angle means the smallest angle, in a plan side view of a vehicle, formed by the level surface on which the vehicle is standing and a line tangent to the front tire static loaded radius arc and touching the underside of the vehicle forward of the front tire. (angle d’approche) auxiliary emission control device means any element of design that senses temperature, vehicle speed, engine RPM, transmission gear, manifold vacuum, or any other parameter for the purpose of activating, modulating, delaying, or deactivating the operation of any part of an emission control system. ((dispositif antipollution auxiliaire)) auxiliary power unit means a device that is installed on a tractor and that is equipped with a diesel engine to generate power for purposes other than propelling the tractor. (groupe électrogène d’appoint) basic vehicle frontal area means the area enclosed by the geometric projection of the basic vehicle, which includes tires but does not include mirrors or air deflectors, along the longitudinal axis of the vehicle onto a plane perpendicular to that axis. (surface frontale du véhicule de base) break-over angle means the supplement of the largest angle, in the plan side view of a vehicle, that can be formed by two lines tangent to the front and rear static loaded radii arcs and intersecting at a point on the underside of the vehicle. (angle de rampe) CFR means the Code of Federal Regulations of the United States, as amended from time to time. (CFR) Class I motorcycle means a motorcycle having an engine displacement of less than 170 cm3. (motocyclette de classe I) Class II motorcycle means a motorcycle having an engine displacement of 170 cm3 or more but less than 280 cm3. (motocyclette de classe II) Class III motorcycle means a motorcycle having an engine displacement of 280 cm3or more. (motocyclette de classe III) Class 2B vehicle means a heavy-duty vehicle that has a GVWR of more than 3 856 kg (8,500 lb) but less than or equal to 4 536 kg (10,000 lb). (véhicule de classe 2B) Class 3 vehicle means a heavy-duty vehicle that has a GVWR of more than 4 536 kg (10,000 lb) but less than or equal to 6 350 kg (14,000 lb). (véhicule de classe 3) complete heavy-duty vehicle[Repealed, SOR/2015-186, s. 1] crankcase emissions means substances that cause air pollution and that are emitted to the atmosphere from any portion of the engine crankcase ventilation or lubrication systems. (émissions du carter) curb weight means, at the manufacturer’s choice, the actual or manufacturer’s estimated weight of a vehicle in operational status with all standard equipment, the weight of fuel at nominal tank capacity and the weight of optional equipment. (masse en état de marche) departure angle means the smallest angle, in a plan side view of a vehicle, formed by the level surface on which the vehicle is standing and a line tangent to the rear tire static loaded radius arc and touching the underside of the vehicle rearward of the rear tire. (angle de sortie) diesel engine means a type of engine that has operating characteristics significantly similar to those of the theoretical Diesel combustion cycle. The non-use of a throttle during normal operation is indicative of a diesel engine. (moteur diesel) diesel heavy-duty vehicle means a heavy-duty vehicle that is powered by a diesel engine. (véhicule lourd diesel) element of design means, in respect of a vehicle or engine, (a) any control system, including computer software, electronic control systems and computer logic; (b) any control system calibrations; (c) the results of systems interaction; or (d) any hardware items. (élément de conception) emission control system means a unique group of emission control devices, auxiliary emission control devices, engine modifications and strategies, and other elements of design used to control exhaust emissions from a vehicle. (système antipollution) engine family means (a) in respect of a company’s motorcycles, (i) if they are covered by an EPA certificate, the grouping for which the EPA certificate was issued, or (ii) if they are not covered by an EPA certificate, the grouping determined in accordance with section 420 of Title 40, chapter I, subchapter C, part 86, subpart E, of the CFR; and (b) in respect of a company’s heavy duty engines, (i) if they are covered by an EPA certificate, the grouping for which the EPA certificate was issued, or (ii) if they are not covered by an EPA certificate, the grouping determined in accordance with section 24 of Title 40, chapter I, subchapter C, part 86, subpart A, of the CFR. (famille de moteurs) EPA means the United States Environmental Protection Agency. (EPA) EPA certificate means a certificate of conformity to U.S. federal standards issued by the EPA under Title 40, chapter I, subchapter C, part 86, of the CFR. (certificat de l’EPA) evaporative emission family means, in respect of a company’s vehicles, for the application of evaporative emission standards, the grouping determined in accordance with section 1821 of Title 40, chapter I, subchapter C, part 86, subpart S, of the CFR. (famille d’émissions de gaz d’évaporation) evaporative emissions means hydrocarbons emitted into the atmosphere from a vehicle, other than exhaust emissions and crankcase emissions. (émissions de gaz d’évaporation) exhaust emissions means substances emitted into the atmosphere from any opening downstream from the exhaust port of a vehicle’s engine. (émissions de gaz d’échappement) family emission limit means the maximum emission level established by a company for a test group, engine family or evaporative emission family. (limite d’émissions de la famille) Federal Test Procedure means the test procedure described in sections 130(a) to (d) and (f) of Title 40, chapter I, subchapter C, part 86, subpart B, of the CFR, which is designed to measure urban driving exhaust emissions and evaporative emissions over the EPA Light-duty Urban Dynamometer Driving Schedule set out in Appendix I to part 86 of Title 40, chapter I, subchapter C, subpart T, of the CFR. (Federal Test Procedure) fire fighting vehicle means a vehicle that is designed to be used under emergency conditions to transport personnel and equipment and to support the suppression of fires and the mitigation of other emergency situations. (véhicule d’incendie) full useful life emission bin means the set of exhaust emission standards, measured using the Federal Test Procedure, that is set out in a horizontal row in the following tables and that is chosen by a company in respect of a test group, taking into account any compliance credits used by the company in accordance with section 1811 of Title 40, chapter I, subchapter C, part 86, subpart S, of the CFR, if applicable: (a) in the case of light-duty vehicles, light-duty trucks and medium-duty passenger vehicles of the 2016 model year or an earlier model year, in Table S04-1 in section 1811 of Title 40, chapter I, subchapter C, part 86, subpart S, of the CFR; (b) in the case of light-duty vehicles, light-duty trucks and medium-duty passenger vehicles of the 2017 model year or a later model year, in Table 2 in section 1811 of Title 40, chapter I, subchapter C, part 86, subpart S, of the CFR; or (c) in the case of the following vehicles of the 2018 model year or a later model year: (i) Class 2B vehicles, in Tables 2 and 5 in section 1816 of Title 40, chapter I, subchapter C, part 86, subpart S, of the CFR, or (ii) Class 3 vehicles, in Tables 3 and 5 in section 1816 of Title 40, chapter I, subchapter C, part 86, subpart S, of the CFR. (série d’émissions de durée de vie totale) GVWR means the gross vehicle weight rating specified by a manufacturer as the maximum design loaded weight of a single vehicle. (PNBV) HC + NOX means the sum of the hydrocarbon and NOX exhaust emissions. (HC + NOX) heavy-duty engine means an engine designed to be used for motive power in a heavy-duty vehicle, other than a medium-duty passenger vehicle, Class 2B vehicle or Class 3 vehicle. (moteur de véhicule lourd) heavy-duty vehicle means an on-road vehicle that has a GVWR of more than 3 856 kg (8,500 lb). (véhicule lourd) heavy light-duty truck means a light-duty truck 3 or a light-duty truck 4 that has a GVWR of more than 2 722 kg (6,000 lb). (camionnette lourde) light-duty truck means an on-road vehicle that has a GVWR of 3 856 kg (8,500 lb) or less and that (a) is designed primarily for the transportation of property or is a derivative of a vehicle that is designed for that purpose; (b) is designed primarily for the transportation of persons and has a designated seating capacity of more than 12 persons; or (c) is available with special features that enable it to be operated and used off-road, the special features being four-wheel drive and at least four of the following characteristics that are calculated when the vehicle is at curb weight and on a level surface with the front wheels parallel to the vehicle’s longitudinal centreline and the tires are inflated to the manufacturer’s recommended pressure: (i) an approach angle of not less than 28°, (ii) a break-over angle of not less than 14°, (iii) a departure angle of not less than 20°, (iv) ground clearances of not less than 17.8 cm (7 in.) under the front and rear axles, and (v) a ground clearance of not less than 20.3 cm (8 in.) under any point other than the front or rear axle. (camionnette) light-duty truck 1 means a light light-duty truck that has a loaded vehicle weight of 1 701 kg (3,750 lb) or less. (camionnette de type 1) light-duty truck 2 means a light light-duty truck that has a loaded vehicle weight of more than 1 701 kg (3,750 lb). (camionnette de type 2) light-duty truck 3 means a heavy light-duty truck that has an adjusted loaded vehicle weight of 2 608 kg (5,750 lb) or less. (camionnette de type 3) light-duty truck 4 means a heavy light-duty truck that has an adjusted loaded vehicle weight of more than 2 608 kg (5,750 lb). (camionnette de type 4) light-duty vehicle means an on-road vehicle that is designed primarily for the transportation of persons and has a designated seating capacity of not more than 12 persons. (véhicule léger) light light-duty truck means a light-duty truck 1 or a light-duty truck 2 that has a GVWR of 2 722 kg (6,000 lb) or less. (camionnette légère) loaded vehicle weight means the sum of the vehicle’s curb weight and 136 kg (300 lb). (poids du véhicule chargé) medium-duty passenger vehicle means a heavy-duty vehicle that has a GVWR of less than 4 536 kg (10,000 lb) and that is designed primarily for the transportation of persons but does not include any vehicle that (a) is a truck that is incomplete because it does not have a primary load carrying device or container attached; (b) has a seating capacity of more than 12 persons; (c) is designed to seat more than 9 persons behind the driver; or (d) is equipped with an open cargo area (for example, a pick-up truck box or bed) of 183 cm (72 in.) in interior length or more or with a covered box not readily accessible from the passenger compartment. (véhicule moyen à passagers) model year means the year, as determined under section 5, that is used by a manufacturer to designate a model of vehicle or engine. (année de modèle) motorcycle means an on-road vehicle with a headlight, tail light and stoplight that has two or three wheels and a curb weight of 793 kg (1,749 lb) or less. (motocyclette) NMHC means non-methane hydrocarbon exhaust emissions. (HCNM) NMOG + NOX means the sum of the non-methane organic gas exhaust emissions and the NOX exhaust emissions. (GONM + NOX) nominal fuel tank capacity means the volume of the fuel tank specified by the manufacturer to the nearest three eighths of a litre (one tenth of a U.S. gallon). (capacité nominale du réservoir à carburant) NOx means oxides of nitrogen, which is the sum of nitric oxide and nitrogen dioxide contained in a gas sample as if the nitric oxide were in the form of nitrogen dioxide. (NOx) on-road vehicle means a self-propelled vehicle designed for or capable of transporting persons, property, material or permanently or temporarily affixed apparatus on a highway, but does not mean a vehicle that (a) cannot exceed a speed of 40 km/h (25 mph) on a level paved surface; (b) lacks features customarily associated with safe and practical highway use such as a reverse gear, unless the vehicle is a motorcycle, a differential, or safety features required by federal or provincial laws; (c) exhibits features that render its use on a highway unsafe, impractical, or highly unlikely, such as tracked road contact means or inordinate size; or (d) is a military vehicle designed for use in combat or combat support. (véhicule routier) Otto-cycle engine means a type of engine that has operating characteristics that are significantly similar to those of the theoretical Otto combustion cycle. The use of a throttle during normal operation is indicative of an Otto-cycle engine. (moteur à cycle Otto) Otto-cycle heavy-duty vehicle means a heavy-duty vehicle that is powered by an Otto-cycle engine. (véhicule lourd à cycle Otto) rounded means rounded in accordance with the rounding method described in section 6 of the ASTM International method ASTM E 29-93a, entitled Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications. (arrondir) static loaded radius arc means a portion of a circle whose centre is the centre of a standard tire-rim combination of a vehicle and whose radius is the distance from that centre to the level surface on which the vehicle is standing, measured with the vehicle at curb weight, the wheel parallel to the vehicle’s longitudinal centreline, and the tire inflated to the manufacturer’s recommended pressure. (arc du rayon sous charge) test group means, in respect of a company’s vehicles other than its motorcycles, (a) if they are covered by an EPA certificate, the grouping for which the EPA certificate was issued; and (b) if they are not covered by an EPA certificate, the grouping determined in accordance with section 1827 of Title 40, chapter I, subchapter C, part 86, subpart S, of the CFR. (groupe d’essai) tractor means a heavy-duty vehicle that has a GVWR of more than 11 793 kg (26,000 lb) and that is manufactured primarily for pulling a trailer but not for carrying cargo other than cargo in the trailer. (tracteur routier) useful life, in respect of a vehicle or engine, means the period of time or use, whether full or intermediate, during which an emission standard applies as set out in the CFR. (durée de vie utile) (2) Standards that are incorporated by reference in these Regulations from the CFR are those expressly set out in the CFR and shall be read as excluding (a) references to the EPA or the Administrator of the EPA exercising discretion in any way; (b) alternative standards related to fleet averages, other averages, emission credits, small volume manufacturers, or financial hardship; and (c) standards or evidence of conformity of any authority other than the EPA and, in the case of the standards referred to in paragraph 12(b), the California Air Resources Board. 1.1 For the purposes of these Regulations, a vehicle or engine of a specific model year that is sold in Canada is considered to be sold concurrently in Canada and in the United States if a vehicle or engine of that model year that belongs to the same test group or engine family is offered for sale in the United States during the 365 days preceding (a) in the case of a vehicle or engine that is imported into Canada, the day on which the vehicle or engine is imported; and (b) in the case of a vehicle or engine that is manufactured in Canada, (i) the day on which the national emissions mark is applied to the vehicle or engine, if known, or (ii) if the day referred to in subparagraph (i) is not known, the day on which the main assembly of the vehicle or the manufacture of the engine, as the case may be, was completed. 2 The purpose of these Regulations is to (a) reduce emissions of hydrocarbons, carbon monoxide, oxides of nitrogen, formaldehyde and particulate matter from on-road vehicles and engines by establishing emission limits for those substances; (b) reduce emissions of the toxic substances 1-3 butadiene, acetaldehyde, acrolein and benzene through the establishment of emission limits for hydrocarbons from on-road vehicles and engines; and (c) establish emission standards and test procedures for on-road vehicles and engines that are aligned with those of the EPA. 2.1 These Regulations set out (a) prescribed classes of on-road vehicles and engines for the purposes of section 149 of the Act; (b) requirements respecting the conformity of on-road vehicles and engines with emission standards for the purposes of sections 153 and 154 of the Act; (c) other requirements for carrying out the purposes of Division 5, Part 7 of the Act; and (d) a system of credits for the purposes of section 162 of the Act. 3 Subject to subsection 24(7), these Regulations apply to vehicles whose main assembly is completed in Canada on or after January 1, 2004, to engines whose manufacture is completed in Canada on or after January 1, 2004 and to vehicles and engines that are imported into Canada on or after January 1, 2004. 4 [Repealed, SOR/2013-8, s. 3] 5 (1) A year that is used by a manufacturer as a model year shall (a) if the period of production of a model of vehicle or engine does not include January 1 of a calendar year, correspond to the calendar year during which the period of production falls; or (b) if the period of production of a model of vehicle or engine includes January 1 of a calendar year, correspond to that calendar year. (2) The period of production of a model of vehicle or engine shall include only one January 1. 6 (1) In these Regulations, subject to subsection (3), the following classes of vehicles are prescribed for the purposes of the definition vehicle in section 149 of the Act: (a) light-duty vehicles; (b) light light-duty trucks and heavy light-duty trucks; (c) medium-duty passenger vehicles; (d) Class 2B vehicles and Class 3 vehicles; (e) heavy-duty vehicles other than medium-duty passenger vehicles, Class 2B vehicles and Class 3 vehicles; and (f) motorcycles. (2) In these Regulations, subject to subsection (3), heavy-duty engines are prescribed for the purposes of the definition engine in section 149 of the Act. (3) The prescribed classes of vehicles and engines referred to in subsections (1) and (2) do not include (a) any vehicle whose main assembly was completed 15 years or more before the date of its importation into Canada; or (b) any vehicle or engine that is being exported and that is accompanied by written evidence establishing that it will not be sold for use or used in Canada. (4) For the purpose of section 152 of the Act, the prescribed vehicles and engines are the classes of vehicles referred to in subsection (1) whose main assembly is completed in Canada and the engines referred to in subsection (2) whose manufacture is completed in Canada, except (a) any vehicle or engine that will be used in Canada solely for purposes of exhibition, demonstration, evaluation or testing; (b) any engine that is to be installed in a heavy-duty vehicle before the first retail sale of the vehicle; and (c) any engine that is to be installed as a replacement in a heavy-duty vehicle that has a national emissions mark applied to it if the replacement engine (i) is of the same model year as the original engine, and (ii) is identical to the original engine in all respects material to emissions. 7 (1) Any company that intends to apply a national emissions mark to a vehicle or engine shall apply to the Minister to obtain an authorization in the form set out in Schedule 1. (2) The application to apply a national emissions mark shall be signed by a person who is authorized to act on behalf of the company and shall include (a) the name and street address of the head office of the company and, if different, its mailing address; (b) the classes of vehicles or engines for which the authorization is requested; (c) the street address of the location at which the national emissions mark will be applied to the vehicles or engines; (d) the street address where records referred to in section 38 will be maintained; and (e) information to show that the company is capable of verifying compliance with the standards set out in these Regulations. 8 (1) The national emissions mark is the mark set out in Schedule 2. (2) The national emissions mark shall be at least 7 mm in height and 10 mm in width. (3) The national emissions mark shall be located (a) on or immediately beside the U.S. information label referred to in paragraph 35(1)(d); or (b) on or immediately beside the compliance label applied in accordance with the Motor Vehicle Safety Regulations. (4) The national emissions mark shall be on a label that (a) is permanently applied to the vehicle or engine; (b) is resistant to or protected against any weather condition; and (c) bears inscriptions that are legible, indelible and that are indented, embossed or in a colour that contrasts with the background of the label. (5) Subject to subsection (6), a company that has been authorized to apply the national emissions mark shall display the authorization number assigned by the Minister in figures that are at least 2 mm in height, immediately below or to the right of the national emissions mark. (6) A company is not required to display its authorization number if (a) the company is authorized by the Minister of Transport to apply the national safety mark in accordance with the Motor Vehicle Safety Act; (b) the company applies both the national emissions mark and the national safety mark to the vehicle; and (c) the national emissions mark is on the same label as the national safety mark. 9 [Repealed, SOR/2013-8, s. 5] 10 [Repealed, SOR/2013-8, s. 5] 11 (1) An emission control system that is installed in a vehicle or engine to enable it to conform to the standards set out in these Regulations shall not (a) in its operation, release a substance that causes air pollution and that would not have been released if the system were not installed; or (b) in its operation or malfunction, make the vehicle unsafe or endanger persons or property in or near the vehicle. (2) No vehicle or engine shall be equipped with a defeat device. (2.1) Despite subsection (2), an ambulance, police vehicle or fire fighting vehicle may be equipped with a defeat device if the device is one that is activated during emergency response operations to maintain speed, torque or power in either of the following circumstances: (a) the emission control system is in an abnormal state, or (b) the device acts to maintain the emission control system in a normal state. (3) Subject to subsection (4), a defeat device is an auxiliary emission control device that reduces the effectiveness of the emission control system under conditions that may reasonably be expected to be encountered in normal vehicle operation and use. (4) An auxiliary emission control device is not a defeat device if (a) the conditions referred to in subsection (3) are substantially included in the test procedures referred to in section 18; (b) it is needed to protect the vehicle against damage or accident; or (c) its use does not go beyond the requirements of engine starting. 11.1 (1) In this section, adjustable parameter means a device, system or element of design that is capable of being physically adjusted and as a result can affect emissions or the performance of a vehicle or an engine during emission testing or normal in-use operation, but does not include a device, system or element of design that is permanently sealed by the vehicle or engine manufacturer or that is inaccessible with the use of ordinary tools. (2) A vehicle or engine that is equipped with adjustable parameters shall comply with the applicable standards under these Regulations for any specification within the physically adjustable range. 12 Subject to sections 17.2, 19 and 19.1, a light-duty vehicle, light light-duty truck, heavy light-duty truck or medium-duty passenger vehicle of a specific model year shall (a) for the 2016 and earlier model years, conform to the exhaust emission and evaporative emission standards applicable to vehicles of the model year in question set out in section 1811 of Title 40, chapter I, subchapter C, part 86, subpart S, of the CFR; (a.1) for the 2017 and later model years, conform to (i) the exhaust emission standards applicable to vehicles of the model year in question set out in section 1811 of Title 40, chapter I, subchapter C, part 86, subpart S, of the CFR, (ii) the evaporative emission and refueling emission standards applicable to vehicles of the model year in question set out in section 1813 of Title 40, chapter I, subchapter C, part 86, subpart S, of the CFR, and (iii) the family emission limit established by the company for the evaporative emission family to which the vehicle belongs, which shall not exceed the applicable family emission limit cap set out in section 1813 of Title 40, chapter I, subchapter C, part 86, subpart S, of the CFR; (b) be equipped with an on-board diagnostic system that conforms to the standards applicable to vehicles of the model year in question set out in section 1806 of Title 40, chapter I, subchapter C, part 86, subpart S, of the CFR; and (c) not release any crankcase emissions. 13 Subject to sections 17.2, 19 and 19.1, a Class 2B vehicle, other than a medium-duty passenger vehicle, and a Class 3 vehicle of a specific model year shall (a) for the 2005 to 2017 model years, conform to the exhaust emission and evaporative emission standards applicable to vehicles of the model year in question set out in section 1816 of Title 40, chapter I, subchapter C, part 86, subpart S, of the CFR; (a.1) for the 2018 and later model years, conform to (i) the exhaust emission standards applicable to vehicles of the model year in question set out in section 1816 of Title 40, chapter I, subchapter C, part 86, subpart S, of the CFR, (ii) the evaporative emission and refueling emission standards applicable to vehicles of the model year in question set out in section 1813 of Title 40, chapter I, subchapter C, part 86, subpart S, of the CFR, and (iii) the family emission limit established by the company for the evaporative emission family to which the vehicle belongs, which shall not exceed the applicable family emission limit cap set out in section 1813 of Title 40, chapter I, subchapter C, part 86, subpart S, of the CFR; (b) be equipped with an on-board diagnostic system that conforms to the standards applicable to vehicles of the model year in question set out in section 1806 of Title 40, chapter I, subchapter C, part 86, subpart S, of the CFR; and (c) not release any crankcase emissions. 14 Subject to sections 19 and 19.1, an Otto-cycle heavy-duty vehicle of a specific model year, other than a medium-duty passenger vehicle, Class 2B vehicle or Class 3 vehicle, shall (a) be equipped with a heavy-duty engine that meets the requirements of these Regulations; and (b) conform to (i) for the 2017 and earlier model years, the evaporative emission standards applicable to vehicles of the model year in question set out in section 10 of Title 40, chapter I, subchapter C, part 86, subpart A, of the CFR, or (ii) for the 2018 and later model years, the evaporative emission and refueling emission standards applicable to vehicles of the model year in question set out in section 103 of Title 40, chapter I, subchapter U, part 1037, subpart B, of the CFR. 15 (1) Subject to subsection (2) and sections 19 and 19.1, a diesel heavy-duty vehicle of a specific model year, other than a medium-duty passenger vehicle, shall (a) be equipped with a heavy-duty engine that meets the requirements of these Regulations; and (b) conform to the evaporative emission and refueling emission standards applicable to diesel heavy-duty vehicles of the model year in question set out in section 1813 of Title 40, chapter I, subchapter C, part 86, subpart S, of the CFR. (2) A vehicle referred to in subsection (1) that has a GVWR of 6 350 kg (14,000 lb) or less may conform to the standards applicable to vehicles of the model year in question referred to in section 1863 of Title 40, chapter I, subchapter C, part 86, subpart S, of the CFR instead of the standards described in subsection (1). 15.1 Tractors of the 2021 and later model years that are equipped with an auxiliary power unit must, in respect of that unit, conform to the following particulate matter exhaust emission standards for the model year of tractor in question for the duration of the unit’s useful life, which is set out in section 101(g) of Title 40, chapter I, subchapter U, part 1039, subpart B, of the CFR: (a) for the 2021 to 2023 model years, the particulate matter exhaust emission standard set out in section 106(g)(1) of Title 40, chapter I, subchapter U, part 1037, subpart B, of the CFR; and (b) for the 2024 and later model years, the particulate matter exhaust emission standard set out in section 699 of Title 40, chapter I, subchapter U, part 1039, subpart G, of the CFR. 16 (1) Subject to sections 19 and 19.1, Otto-cycle heavy-duty engines of a specific model year shall conform to the exhaust emission and crankcase emission standards applicable to Otto-cycle heavy-duty engines of the model year in question set out in section 10 of Title 40, chapter I, subchapter C, part 86, subpart A, of the CFR. (2) Subject to sections 19 and 19.1, diesel heavy-duty engines of a specific model year shall conform to the exhaust emission and crankcase emission standards applicable to diesel heavy-duty engines of the model year in question set out in section 11 of Title 40, chapter I, subchapter C, part 86, subpart A, of the CFR. (3) Subject to sections 19 and 19.1, heavy-duty engines of a specific model year used or intended for use in heavy-duty vehicles that have a GVWR of 6 350 kg (14,000 lb) or less shall be equipped with an on-board diagnostic system that conforms to the standards applicable to engines of the model year in question set out in section 17 of Title 40, chapter I, subchapter C, part 86, subpart A, of the CFR. (4) Subject to sections 19 and 19.1, heavy-duty engines of the 2014 and later model years used or intended for use in heavy-duty vehicles that have a GVWR of more than 6 350 kg (14,000 lb) shall be equipped with an on-board diagnostic system that conforms to the standards applicable to engines of the model year in question set out in section 18 of Title 40, chapter I, subchapter C, part 86, subpart A, of the CFR. 17 Subject to sections 17.1, 19, 19.1 and 32.2, motorcycles of a specific model year (a) shall conform to the exhaust emission and evaporative emission standards applicable to motorcycles of the model year in question set out in section 410 of Title 40, chapter I, subchapter C, part 86, subpart E, of the CFR; and (b) shall not release any crankcase emissions. 17.1 (1) A company that manufactures or imports fewer than 200 motorcycles for sale in Canada per year and has fewer than 500 employees worldwide is exempt from the requirement to conform to the HC+NOx emission standard set out in the section of the CFR that is referred to in paragraph 17(a) in respect of its Class III motorcycles of the 2006 and 2007 model years that conform to the hydrocarbon emission standard referred to in that section and applicable to 2005 model year motorcycles. (2) A company that manufactures or imports fewer than 200 motorcycles for sale in Canada per year and has fewer than 500 employees worldwide is exempt from the requirement to conform to the HC+NOx emission standard set out in the section of the CFR that is referred to in paragraph 17(a) in respect of its Class III motorcycles of the 2010 and later model years that conform to the HC+NOx emission standard referred to in that section and applicable to 2009 model year motorcycles. (3) A company that manufactures or imports fewer than 200 motorcycles for sale in Canada per year and having fewer than 500 employees worldwide is exempt from the requirement to conform to the applicable evaporative emission standards set out in the section of the CFR that is referred to in paragraph 17(a) in respect of its 2008 and 2009 model year motorcycles. 17.2 (1) Subject to subsection (3), for the purposes of subparagraphs 12(a.1)(i) and 13(a.1)(i), the particulate matter exhaust emission standards set out in section 1811 or 1816 of Title 40, chapter I, subchapter C, part 86, subpart S, of the CFR, as the case may be, apply to a percentage of a company’s vehicles referred to in section 12 or 13 of a specific model year, in accordance with subsection (5) or (6). (2) For the purposes of subsection (1), a company shall group its vehicles together as follows: (a) in the case of the vehicles referred to in section 12 (i) for the 2017 model year, all of its light-duty vehicles and light light-duty trucks of that model year, and (ii) for the 2018 and later model years, all of its light-duty vehicles, light-duty trucks and medium-duty passenger vehicles of the model year in question; and (b) in the case of the vehicles referred to in section 13, for the 2018 and later model years, all of its Class 2B vehicles and Class 3 vehicles of the model year in question. (3) For the 2017 to 2021 model years, a company shall calculate the percentage of its vehicles of a specific model year in a given group that conform to the standards referred to in subsection (1) unless each vehicle in the group (a) is covered by an EPA certificate, conforms to the particulate matter exhaust emission standards referred to in the EPA certificate and is of a model that is sold in greater numbers in the United States than in Canada; or (b) conforms to the particulate matter exhaust emission standard set out in Table 1 in section 1811 of Title 40, chapter I, subchapter C, part 86, subpart S, of the CFR or Table 1 in section 1816 of Title 40, chapter I, subchapter C, part 86, subpart S, of the CFR, as applicable, whether or not it is covered by an EPA certificate. (4) In determining the number of vehicles of a given group that are to meet the particulate matter exhaust emission standards referred to in subsection (1), in accordance with the applicable percentage, a company may exclude from the group all of its vehicles that are covered by an EPA certificate and that are of a model that is sold in greater numbers in the United States than in Canada. (5) Subject to subsection (6), the percentage of vehicles of a specific model year in a given group that conform to the applicable particulate matter exhaust emission standards shall be greater than or equal to the percentage set out in column 2 of the table to this subsection for the applicable model year set out in column 1. (6) A company may elect not to comply with subsection (5) for the 2017 to 2020, 2018 to 2020 or 2019 to 2020 model years if (a) the total percentage of vehicles of the group for all of the applicable consecutive model years set out in column 1 of the table to this subsection that conform to the particulate matter exhaust emission standards is greater than or equal to the percentage set out in column 2 for those consecutive model years; and (b) the company notifies the Minister of its election before January 1 of the calendar year that corresponds to the first of the applicable consecutive model years set out in column 1 of the table to this subsection. (7) For greater certainty, all companies shall comply with subsection (5) for the 2021 and later model years. 18 The standards referred to in sections 11 to 17 are the certification and in-use standards set out in the CFR for the applicable useful life and include the test procedures, fuels, calculation methods, compliance credits and allowances set out in the CFR for those standards. 19 (1) Every vehicle or engine of a specific model year that is covered by an EPA certificate and bears the U.S. emission control information label referred to in paragraph 35(1)(d) may, if the company so chooses, conform to, instead of the standards set out in sections 11 to 17, the certification and in-use standards referred to in the EPA certificate. (2) For the purposes of subsection 153(3) of the Act, the provisions of the CFR that are applicable to a vehicle or engine referred to in subsection (1) pursuant to the EPA certificate correspond to the certification and in-use standards referred to in subsection (1). (3) For the purposes of subsection 153(3) of the Act, the EPA is the prescribed agency. 19.1 (1) A vehicle of a specific model year that is not covered by an EPA certificate may be considered equivalent to a vehicle that is covered by an EPA certificate if a company submits the evidence of conformity referred to in section 35.1 in respect of that vehicle instead of the evidence of conformity referred to in section 36. (2) The equivalency of a vehicle is determined by the Minister on the basis of the evidence of conformity referred to in section 35.1. (3) Every vehicle of a specific model year that is determined to be equivalent to a vehicle covered by an EPA certificate and that is sold in Canada during the period for which that EPA certificate is valid in the United States shall conform to, instead of the standards set out in sections 11 to 17, the certification and in-use standards referred to in that EPA certificate. 20 In sections 21 to 32, fleet refers to the vehicles of a specific model year that a company manufactures in Canada, or imports into Canada, for the purpose of sale to the first retail purchaser and that are grouped for the purpose of conforming to sections 21 to 23, 24.1 to 24.4, 24.6, 24.7 and 24.10 or for the purpose of participation in the emission credit system set out in sections 26 to 31.1. 21 The average NOX value for a company’s fleet that is composed of all of its light-duty vehicles and light light-duty trucks of a model year set out in column 1 of the table to this section shall not exceed the applicable fleet average NOX standard set out in column 2. 22 The average NOX value for a company’s fleet that is composed of all of its heavy light-duty trucks and medium-duty passenger vehicles of a model year set out in column 1 of the table to this section shall not exceed the applicable fleet average NOX standard set out in column 2. 23 (1) For the 2009 to 2016 model years, the average NOX value for a company’s fleet that is composed of all of its light-duty vehicles, light-duty trucks and medium-duty passenger vehicles of the model year in question shall not exceed 0.07 grams per mile. (2) For the 2017 model year, the average NOX value for a company’s fleet that is composed of all of its heavy light-duty trucks and medium-duty passenger vehicles of that model year shall not exceed 0.07 grams per mile. 24 (1) Subject to section 25, for each of its fleets referred to in sections 21 to 23, a company shall calculate the average NOx value in accordance with the following formula: is the NOx emission standard for each full useful life emission bin, is the number of vehicles in the fleet that conform to that NOx emission standard, and is the total number of vehicles in the fleet. (2) The average NOx value for the fleet shall be rounded to the same number of significant figures that are contained in the total number of vehicles in the fleet in the denominator in subsection (1), but to at least three decimal places. (3) If a company’s fleet includes any hybrid electric vehicle that is covered by an EPA certificate, the average NOx value calculated under subsection (1) may be lowered by applying one or more hybrid electric vehicle NOx contribution factors as long as (a) each factor has been approved by the EPA in accordance with the provisions of the CFR; (b) each factor is applied in the same manner as it is applied by the EPA; and (c) evidence of the EPA approval is provided to the Minister in the end of model year report referred to in section 32. (4) Subject to subsection (5), in respect of any of its vehicles that conform to a NOX emission standard for an extended useful life of 150,000 miles, a company may, in the formula in subsection (1), replace that standard, for each of those vehicles, with that standard multiplied by 0.85, rounded to at least three decimal places. (5) A company may only replace a NOx emission standard as described in subsection (4) if the vehicle complies with any standards that may be applicable at the intermediate useful life. (6) In respect of the 2004 and 2005 model years, a company may multiply by 2 the number of vehicles that conform to full useful life emission bin 1, and multiply by 1.5 the number of vehicles that conform to full useful life emission bin 2, when calculating one of the following: (a) the denominator in subsection (1); or (b) “total number of vehicles in the fleet” in the equation for calculating credits in subsection 26(2). (7) When calculating the average NOx value under subsection (1) for a fleet of the 2004 model year, a company may include all vehicles of that model year, including those whose main assembly was completed before January 1, 2004. 24.1 (1) Subject to subsection (2), for the 2017 to 2024 model years, the average NMOG + NOX value for each of the following fleets of a specific model year shall not exceed the applicable fleet average NMOG + NOX standard set out for the model year in question in Tables 3 and 4 of section 1811 of Title 40, chapter I, subchapter C, part 86, subpart S, of the CFR: (a) a company’s fleet that is composed of all of its light-duty vehicles and light-duty trucks 1 to which the applicable NMOG + NOX standard applies for a useful life of 120,000 miles; (b) a company’s fleet that is composed of all of its light-duty vehicles and light-duty trucks 1 to which the applicable NMOG + NOX standard applies for a useful life of 150,000 miles; and (c) a company’s fleet that is composed of all of its light-duty trucks 2, heavy light-duty trucks and medium-duty passenger vehicles. (2) For the 2017 model year, the fleet referred to in paragraph (1)(c) is composed only of all of a company’s light-duty trucks 2. 24.2 For the 2025 and later model years, the average NMOG + NOX value for each of the following fleets of a specific model year shall not exceed the applicable fleet average NMOG + NOX standard set out in Table 1 of section 1811 of Title 40, chapter I, subchapter C, part 86, subpart S, of the CFR: (a) a company’s fleet that is composed of all of its light-duty vehicles and light-duty trucks 1 to which the applicable NMOG + NOX standard applies for a useful life of 120,000 miles; (b) a company’s fleet that is composed of all of its light-duty vehicles and light-duty trucks 1 to which the applicable NMOG + NOX standard applies for a useful life of 150,000 miles; and (c) a company’s fleet that is composed of all of its light-duty trucks 2, heavy light-duty trucks and medium-duty passenger vehicles. 24.3 For the 2018 to 2021 model years, the average NMOG + NOX value for each fleet that is composed of all of a company’s Class 2B vehicles or all of a company’s Class 3 vehicles of a specific model year shall not exceed the applicable fleet average NMOG + NOX standard set out for the model year in question in Table 4 of section 1816 of Title 40, chapter I, subchapter C, part 86, subpart S, of the CFR. 24.4 For the 2022 and later model years, the average NMOG + NOX value for each fleet that is composed of all of a company’s Class 2B vehicles or all of a company’s Class 3 vehicles of a specific model year shall not exceed the applicable fleet average NMOG + NOX standard set out in Table 1 of section 1816 of Title 40, chapter I, subchapter C, part 86, subpart S, of the CFR. 24.5 (1) Subject to section 25.1, for each of a company’s fleets referred to in sections 24.1 to 24.4, the company shall calculate the average NMOG + NOX value in accordance with the following formula: is the NMOG + NOX standard for each full useful life emission bin; is the number of vehicles in the fleet that conform to the NMOG + NOX standard for the full useful life emission bin in question; and is the total number of vehicles in the fleet. (2) The average NMOG + NOX value for the fleet shall be rounded to the same number of significant figures that are contained in the total number of vehicles in the fleet in the denominator in subsection (1), but to at least three decimal places. 24.6 For the 2017 and later model years, the average cold NMHC value for a company’s fleet that is composed of all of its light-duty vehicles and light light-duty trucks of a specific model year that are fueled by gasoline shall not exceed the applicable fleet average cold NMHC standard set out in Table 5 to section 1811 of Title 40, chapter I, subchapter C, part 86, subpart S, of the CFR. 24.7 For the 2017 and later model years, the average cold NMHC value for a company’s fleet that is composed of all of its heavy light-duty trucks and medium-duty passenger vehicles of a specific model year that are fueled by gasoline shall not exceed the fleet average cold NMHC standard set out for heavy light-duty trucks in Table 5 to section 1811 of Title 40, chapter I, subchapter C, part 86, subpart S, of the CFR. 24.8 (1) Subject to section 25.2, for each of a company’s fleets referred to in sections 24.6 and 24.7, the company shall calculate the average cold NMHC value in accordance with the following formula: is the family emission limit for cold NMHC for each test group; is the number of vehicles in the fleet that conform to the family emission limit for the test group in question; and is the total number of vehicles in the fleet. (2) The average cold NMHC value for the fleet shall be rounded to one decimal place. 24.9 For the purposes of sections 24.10, 24.11, 25.3, 26.3, 27 and 28, for vehicles of a specific model year, the following groupings are considered to constitute separate fleets for the purpose of evaporative emission averaging: (a) all of a company’s light-duty vehicles and light-duty trucks 1; (b) all of a company’s light-duty trucks 2; (c) all of a company’s heavy light-duty trucks and medium-duty passenger vehicles; and (d) all of a company’s Class 2B vehicles and Class 3 vehicles. 24.10 (1) The average evaporative emission value for the following fleets of a specific model year shall not exceed the applicable fleet average evaporative emission standards set out in Table 1 of section 1813 of Title 40, chapter I, subchapter C, part 86, subpart S, of the CFR for the percentage of vehicles of the model year in question referred to in subsection (5) or (6): (a) for the 2017 and later model years, a company’s fleet of light-duty vehicles and light-duty trucks 1 and a company’s fleet of light-duty trucks 2; and (b) for the 2018 and later model years, a company’s fleet of heavy light-duty trucks and medium-duty passenger vehicles and a company’s fleet of Class 2B vehicles and Class 3 vehicles. (2) For the 2017 to 2022 model years, a company shall calculate the percentage of its vehicles of the model year in question in a given fleet that conform to the applicable standards referred to in subsection (1) unless each vehicle in the fleet (a) is covered by an EPA certificate, conforms to the evaporative emission standards referred to in the EPA certificate and is of a model that is sold in greater numbers in the United States than in Canada; or (b) conforms to the applicable evaporative emission standards set out in Table 1 of section 1813 of Title 40, chapter I, subchapter C, part 86, subpart S, of the CFR, whether or not it is covered by an EPA certificate. (3) For the 2017 to 2022 model years, a company may, in calculating the percentage of its vehicles of the model year in question in a given fleet that conform to the applicable standards referred to in subsection (1), take into account the allowances set out in section 1813(g)(1) of Title 40, chapter I, subchapter C, part 86, subpart S, of the CFR. (4) In determining the number of vehicles in a given fleet that are to meet the evaporative emission standards referred to in subsection (1), in accordance with the applicable percentage, a company may exclude from the fleet all of its vehicles that are covered by an EPA certificate and that are of a model that is sold in greater numbers in the United States than in Canada. (5) Subject to subsection (6), the percentage of vehicles of a specific model year in a given fleet that meet the evaporative emission standards referred to in subsection (1) shall be greater than or equal to the percentage set out in Table 3 of section 1813 of Title 40, chapter I, subchapter C, part 86, subpart S, of the CFR for the model year in question and, for the 2023 and later model years, 100 percent of the vehicles of the model year in question in a fleet shall meet the applicable evaporative emission standards. (6) A company may elect not to comply with subsection (5) for the 2017 to 2021, 2018 to 2021, 2019 to 2021 or 2020 to 2021 model years if (a) the total percentage of vehicles in the fleet for all of the applicable consecutive model years set out in column 1 of the table to this subsection that conform to the evaporative emission standards is greater than or equal to the percentage set out in column 2 for those consecutive model years; and (b) the company notifies the Minister of its election before January 1 of the calendar year that corresponds to the first of the applicable consecutive model years set out in column 1 of the table to this subsection. (7) For greater certainty, all companies shall comply with subsection (5) for the 2022 and later model years. 24.11 (1) Subject to section 25.3, for each of a company’s fleets referred to in section 24.10, the company shall calculate the average evaporative emission value in accordance with the following formula: is the family emission limit for each evaporative emission family; is the number of vehicles in the fleet that conform to the family emission limit for the evaporative emission family in question; and is the total number of vehicles in the fleet. (2) The average evaporative emission value for the fleet shall be rounded to one decimal place. 25 (1) A company may elect not to calculate an average NOx value for a fleet of a specific model year if every vehicle in that fleet conforms to a full useful life emission bin that has a NOx standard equal to or less than the applicable fleet average NOx standard for that model year that is set out in section 21, 22 or 23. (2) For the purposes of section 26, subparagraph 32(2)(a)(ii) and paragraph 37(1)(c), the average NOX value in respect of a fleet of a model year for which a company makes an election under subsection (1) shall be the fleet average NOX standard applicable to the fleet for which the election was made. 25.1 (1) A company may elect not to calculate an average NMOG + NOX value for a fleet of a specific model year if every vehicle in that fleet conforms to a full useful life emission bin that has a NMOG + NOX standard equal to or less than the applicable fleet average NMOG + NOX standard for the model year in question that is referred to in section 24.1 or 24.2. (2) For the purposes of section 26.1, subparagraph 32(2)(b)(ii) and paragraph 37(1)(c), the average NMOG + NOX value in respect of a fleet of a model year for which a company makes an election under subsection (1) shall be the fleet average NMOG + NOX standard applicable to the fleet for which the election was made. 25.2 (1) A company may elect not to calculate an average cold NMHC value for a fleet of a specific model year if every vehicle in that fleet conforms to a cold NMHC family emission limit that is equal to or less than the applicable fleet average cold NMHC standard for the model year in question that is referred to in section 24.6 or 24.7. (2) For the purposes of section 26.2, subparagraph 32(2)(c)(ii) and paragraph 37(1)(c), the average cold NMHC value in respect of a fleet of a model year for which a company makes an election under subsection (1) shall be the fleet average cold NMHC standard applicable to the fleet for which the election was made. 25.3 (1) A company may elect not to calculate an average evaporative emission value for a fleet of a specific model year if every vehicle in that fleet conforms to a family emission limit for an evaporative emission family and that family emission limit is equal to or less than the applicable fleet average evaporative emission standard for the model year in question referred to in section 24.10. (2) For the purposes of section 26.3, subparagraph 32(2)(d)(ii) and paragraph 37(1)(c), the average evaporative emission value in respect of a fleet of a model year for which a company makes an election under subsection (1) shall be the fleet average evaporative emission standard applicable to the fleet for which the election was made. 26 (1) For the purposes of subparagraph 162(1)(b)(i) of the Act, a company shall obtain NOX emission credits for its fleets of the 2017 and earlier model years if the average NOX value in respect of a fleet of a specific model year is lower than the fleet average NOX standard for the model year in question and the company reports the credits in its end of model year report. (2) NOx emission credits, expressed in units of vehicle-grams per mile, shall be calculated using the following formula, rounding the result to the nearest whole number: is the fleet average NOx standard is the average NOx value in respect of the fleet, and is the total number of vehicles in the fleet. (3) The NOx emission credits for a specific model year are credited on the last day of that model year. 26.1 (1) For the purposes of subparagraph 162(1)(b)(i) of the Act, a company shall obtain NMOG + NOX emission credits for its fleets of the 2017 and later model years if the average NMOG + NOX value in respect of a fleet of a specific model year is lower than the fleet average NMOG + NOX standard for the model year in question and the company reports the credits in its end of model year report. (2) NMOG + NOX emission credits, expressed in units of vehicle-grams per mile, shall be calculated using the following formula, rounding the result to the nearest whole number: is the fleet average NMOG + NOX standard; is the average NMOG + NOX value in respect of the fleet; and is the total number of vehicles in the fleet. (3) The NMOG + NOX emission credits for a specific model year are credited on the last day of the model year in question. 26.2 (1) For the purposes of subparagraph 162(1)(b)(i) of the Act, a company shall obtain cold NMHC emission credits for its fleets of the 2017 and later model years if the average cold NMHC value in respect of a fleet of a specific model year is lower than the fleet average cold NMHC standard for the model year in question and the company reports the credits in its end of model year report. (2) Cold NMHC emission credits, expressed in units of vehicle-grams per mile, shall be calculated using the following formula, rounding the result to the nearest whole number: is the fleet average cold NMHC standard; is the average cold NMHC value in respect of the fleet; and is the total number of vehicles in the fleet. (3) The cold NMHC emission credits for a specific model year are credited on the last day of the model year in question. 26.3 (1) For the purposes of subparagraph 162(1)(b)(i) of the Act, a company shall obtain evaporative emission credits for its fleets of the 2017 and later model years if the average evaporative emission value in respect of a fleet of a specific model year is lower than the fleet average evaporative emission standard for the model year in question and the company reports the credits in its end of model year report. (2) Evaporative emission credits, expressed in units of vehicle-grams per mile, shall be calculated using the following formula, rounding the result to the nearest whole number: is the fleet average evaporative emission standard; is the average evaporative emission value in respect of the fleet; and is the total number of vehicles in the fleet. (3) The evaporative emission credits for a specific model year are credited on the last day of the model year in question. 26.4 (1) A company may obtain early action credits in respect of its fleet that is composed of all of its light-duty vehicles and light-duty trucks 1 of the 2015 or 2016 model year if the average NMOG + NOX value in respect of the fleet of the model year in question is lower than 0.16 grams per mile and the company reports the credits in its 2017 end of model year report. (2) Early action credits obtained in respect of the fleet are calculated in accordance with subsection 26.1(2), except that the fleet average NMOG + NOX standard in the description of A is 0.16 grams per mile. (3) Early action credits obtained for the 2015 and 2016 model years are credited on the day on which the company’s 2017 end of model year report is submitted. (4) Early action credits obtained for the 2015 and 2016 model years may be used as of the 2017 model year but only in respect of a fleet that is composed of all of the company’s light-duty vehicles and light-duty trucks 1 of any of the five model years after the model year in respect of which the credits were credited, after which the credits are no longer valid. 26.5 (1) A company may obtain early action credits in respect of its fleet that is composed of all of its light-duty trucks 2, heavy light-duty trucks and medium-duty passenger vehicles of the 2016 or 2017 model year if the average NMOG + NOX value in respect of the fleet of the model year in question is lower than 0.16 grams per mile and the company reports the credits in its 2018 end of model year report. (2) Early action credits obtained in respect of the fleet are calculated in accordance with subsection 26.1(2), except that the fleet average NMOG + NOX standard in the description of A is 0.16 grams per mile. (3) Early action credits obtained for the 2016 and 2017 model years are credited on the day on which the company’s 2018 end of model year report is submitted. (4) Early action credits obtained for the 2016 and 2017 model years may be used as of the 2018 model year but only in respect of a fleet that is composed of all of the company’s light-duty trucks 2, heavy light-duty trucks and medium-duty passenger vehicles of any of the five model years after the model year in respect of which the credits were credited, after which the credits are no longer valid. 26.6 (1) A company may obtain early action credits in respect of its fleet that is composed of all of its Class 2B vehicles or all of its Class 3 vehicles of the 2016 or 2017 model year if the average NMOG + NOX value in respect of a fleet of the model year in question is lower than the applicable fleet average NMOG + NOX standard for the model year in question set out in Table 4 of section 1816 of Title 40, chapter I, subchapter C, part 86, subpart S, of the CFR and the company reports the credits in its 2018 end of model year report. (2) Early action credits obtained in respect of the fleet are calculated in accordance with subsection 26.1(2). (3) Early action credits obtained for the 2016 and 2017 model years are credited on the day on which the company’s 2018 end of model year report is submitted. (4) Early action credits obtained for the 2016 and 2017 model years may be used as

    The text continues in the official source.

    Related guides, FAQ and contract templates