Beta
SOR-2000-210:en
SOR-2000-210:en — Nuclear Non-proliferation Import and Export Control Regulations
Beta. Legal information, not legal advice. LEGALDIGM is not a law firm. Check the official source for the current text.
Analyze this law with AI1 (1) The definitions in this subsection apply in these Regulations.
Act means the Nuclear Safety and Control Act. (Loi)
controlled nuclear equipment means the controlled nuclear equipment and the parts and components for controlled nuclear equipment referred to in the schedule. (équipement nucléaire contrôlé)
controlled nuclear information means the controlled nuclear information referred to in the schedule. (renseignement nucléaire contrôlé)
controlled nuclear substance means a controlled nuclear substance referred to in the schedule. (substance nucléaire contrôlée)
transit means the process of being transported through Canada after being imported into and before being exported from Canada, in a situation where the place of initial loading and the final destination are outside Canada. (transit)
(2) All controlled nuclear substances are prescribed as nuclear substances for the purpose of paragraph (d) of the definition nuclear substance in section 2 of the Act, with respect to the import and export of those substances.
(3) All controlled nuclear equipment is prescribed equipment for the purposes of the Act, with respect to the import and export of that equipment.
(4) All controlled nuclear information is prescribed information for the purposes of the Act, with respect to the import and export of that information, unless it is made public in accordance with the Act, the regulations made under the Act or a licence.
2 These Regulations apply in respect of the import and export of controlled nuclear substances, controlled nuclear equipment and controlled nuclear information.
3 (1) An application for a licence to import or export a controlled nuclear substance, controlled nuclear equipment or controlled nuclear information shall contain the following information:
(a) the applicant’s business number assigned by the Canada Revenue Agency, if applicable, their name, Canadian address, email address and telephone number;
(b) a description of the substance, equipment or information, including its quantity and the number of the paragraph of the schedule in which it is referred to;
(c) the name and address of the supplier;
(d) the country of origin of the substance, equipment or information;
(e) the name, address and, where the application is for a licence to import, telephone number of each consignee;
(f) the intended end-use of the substance, equipment or information by the final consignee and the intended end-use location;
(g) the number of any licence to possess the substance, equipment or information;
(h) where the application is in respect of a controlled substance that is Category I, II or III nuclear material, as defined in section 1 of the Nuclear Security Regulations, the measures that will be taken to facilitate Canada’s compliance with the Convention on the Physical Protection of Nuclear Material, INFCIRC/274/Rev.1; and
(i) the applicant’s written process for the import or export of the substance, equipment or information.
(2) The Commission or any designated officer who is authorized to carry out the duties set out in paragraphs 37(2)(c) and (d) of the Act may request any other information that is necessary to enable the Commission or that officer to form the opinion referred to in subsection 24(4) of the Act.
3.1 Every person must retain, for a period of six years after the day on which a licence to import or export issued to them expires, the licence and all records relevant to any import or export under it, including, if applicable,
(a) the application for the licence and supporting information submitted to the Commission or any designated officer who is authorized to carry out the duties set out in paragraphs 37(2)(c) and (d) of the Act;
(b) the customs declaration and associated documentation submitted at the time of import or export;
(c) shipping manifests and associated documentation;
(d) any purchase order and certificate of manufacture; and
(e) the notifications and other reporting submissions made under the licence.
4 (1) A person may carry on any of the following activities without a licence to carry on that activity:
(a) import a controlled nuclear substance referred to in Part B of the schedule;
(b) import controlled nuclear equipment referred to in paragraph A.3 or Part B of the schedule;
(c) import controlled nuclear information that relates to a controlled nuclear substance or controlled nuclear equipment referred to in paragraph A.3 or Part B of the schedule;
(d) import a controlled nuclear substance, controlled nuclear equipment or controlled nuclear information for the purpose of placing it in transit;
(e) export a controlled nuclear substance, controlled nuclear equipment or controlled nuclear information after it has been in transit;
(e.1) import, in a quantity of 200 kg or less per shipment, a controlled nuclear substance referred to in paragraph A.1.3 of the schedule that is not for use in a nuclear reactor;
(f) export a controlled nuclear substance referred to in paragraph A.1.4 of the schedule that is not for use in a nuclear reactor to any Participating Government of the Nuclear Suppliers Group;
(g) import a controlled nuclear substance referred to in paragraph A.1.4 of the schedule that is not for use in a nuclear reactor;
(h) import a controlled nuclear substance referred to in paragraph A.1.5 of the schedule that is contained in a self-luminous source or self-luminous device; or
(i) export, to any Participating Government of the Nuclear Suppliers Group a controlled nuclear substance referred to in paragraph A.1.5 of the schedule that is contained in a self-luminous source or self-luminous device, if that source or device contains less than 1 480 GBq of tritium.
(2) For greater certainty, the exemptions established in subsection (1) relate only to the activities specified in that subsection and do not derogate from the licence requirement imposed by section 26 of the Act in relation to other activities.
(3) Every person who exports a controlled nuclear substance under paragraph (1)(f) or (i) must, by January 31, submit to the Commission a written report that includes the following information regarding every export of the controlled nuclear substance in the previous calendar year:
(a) the exporter’s name, address and telephone number;
(b) a description of the controlled nuclear substance, including the quantity exported and country of origin;
(c) the date of export;
(d) the name and address of each consignee; and
(e) the intended end-use and end-use location of the controlled nuclear substance as stated by the final consignee.
(4) Paragraph (1)(i) applies only to exports that are intended for end-use in States that are signatories to the Treaty on the Non-Proliferation of Nuclear Weapons that was signed by Canada at London and Washington on July 23, 1968 and at Moscow on July 29, 1968 and that came into force for Canada on March 5, 1970.
5 These Regulations come into force on the day on which they are approved by the Governor in Council.
SCHEDULE(Sections 1 and 4)Controlled Nuclear Substances, Equipment and InformationThe following lists are reproduced, in rearranged form and with some modifications, from International Atomic Energy Agency Information Circulars INFCIRC/254/Rev.14/Part 1, INFCIRC/254/Rev.12/Part 2 and INFCIRC/209/Rev.5.
PART AList of Nuclear ItemsA.1. Controlled Nuclear Substances A.1.1. Special fissionable material, as follows:
(a)plutonium and all isotopes, alloys and compounds and any material that contains any of these substances; and
(b)uranium 233, uranium enriched in the isotopes 235 or 233 and all alloys and compounds and any material that contains any of these substances.
NOTE
Paragraph A.1.1. does not include
(a)special fissionable material occurring as contaminants in laundry, packaging, shielding, equipment or biological samples;
(b)special fissionable material used as a sensing component in instruments in quantities of four effective grams or less; or
(c)plutonium 238 that is contained in heart pacemakers.
A.1.2Source material
The following source materials in any form, including ore, concentrate, compound, metal or alloy, or incorporated in any substance, other than medicinals, and in which the concentration of source material is greater than 0.05 weight %:
(a)uranium that contains the mixture of isotopes that occurs in nature;
(b)uranium that is depleted in the isotope 235; and
(c)thorium.
NOTE
Paragraph A.1.2. does not include
(a)source material occurring as contaminants in laundry, packaging, shielding, equipment or biological samples; or
(b)depleted uranium used as ballasts, counterweights or shielding for Class II prescribed equipment, as defined in section 1 of the Class II Nuclear Facilities and Prescribed Equipment Regulations, for radiation devices or for transport packaging; or
(c)thorium used in civil non-nuclear applications, including thorium contained in lamps, lights, welding rods and engine coatings. This exemption does not apply to bulk imports or exports of thorium for the manufacture of these items.
A.1.3Deuterium and heavy water
Deuterium, heavy water (deuterium oxide) and any other deuterium compound in which the ratio of deuterium to hydrogen atoms exceeds 1:5,000.
NOTE
Paragraph A.1.3. does not include
(a)deuterium contained in deuterium lamps;
(b)deuterium occurring as a contaminant in laundry, packaging, shielding, equipment or biological samples;
(c)any deuterium compound that is used for labelling purposes; or
(d)deuterium contained in pharmaceutical products.
A.1.4Nuclear grade graphite
Graphite having a purity level better than 5 ppm boron equivalent and with a density greater than 1.50 g/cm3.
NOTE
Paragraph A.1.4 does not include exports, in quantities of 1 kg or less per shipment, of nuclear grade graphite that is not for use in a nuclear reactor.
A.1.5Tritium
Tritium, tritium compounds or mixtures containing tritium in which the ratio of tritium to hydrogen by atoms exceeds 1 part in 1000 and products that contain any of these substances.
NOTE
Paragraph A.1.5 does not include
(a)tritium contained in self-luminous devices, for illumination, that have been installed in conveyances, including aircrafts, ships or vehicles;
(b)tritium contained in watches, compasses, jewellery or gunsights;
(c)tritium occurring as a contaminant in laundry, packaging, shielding, equipment or biological samples; or
(d)tritium contained in pharmaceutical products.
A.2. Controlled Nuclear Equipment A.2.1Nuclear reactors and especially designed or prepared equipment and components therefor, including:
A.2.1.1Complete nuclear reactors
Nuclear reactors capable of operation so as to maintain a controlled self-sustaining fission chain reaction.
A.2.1.2Nuclear reactor vessels
Metal vessels, or major shop-fabricated parts for these vessels, especially designed or prepared to contain the core of a nuclear reactor within the meaning of paragraph A.2.1.1, as well as relevant nuclear reactor internals within the meaning of paragraph A.2.1.8.
NOTE
Paragraph A.2.1.2 includes nuclear reactor vessels regardless of pressure rating, as well as reactor pressure vessels and calandrias. It includes the reactor vessel head as a major shop-fabricated part of a reactor vessel.
A.2.1.3Nuclear reactor fuel charging and discharging machines
Manipulative equipment especially designed or prepared for inserting or removing fuel in a nuclear reactor within the meaning of paragraph A.2.1.1.
A.2.1.4Nuclear reactor control rods and equipment
Especially designed or prepared rods, support or suspension structures for those rods, rod drive mechanisms or rod guide tubes to control the fission process in a nuclear reactor within the meaning of paragraph A.2.1.1.
A.2.1.5Nuclear reactor pressure tubes
Tubes especially designed or prepared to contain both fuel elements and the primary coolant in a nuclear reactor within the meaning of paragraph A.2.1.1.
A.2.1.6Nuclear fuel cladding
Zirconium metal tubes or zirconium alloy tubes, or assemblies of tubes, especially designed or prepared for use as fuel cladding in a nuclear reactor within the meaning of paragraph A.2.1.1.
A.2.1.7Primary coolant pumps or circulators
Pumps or circulators especially designed or prepared for circulating the primary coolant for a nuclear reactor within the meaning of paragraph A.2.1.1.
A.2.1.8Nuclear reactor internals
Nuclear reactor internals especially designed or prepared for use in a nuclear reactor within the meaning of paragraph A.2.1.1. This includes, for example, support columns for the core, fuel channels, calandria tubes, thermal shields, baffles, core grid plates and diffuser plates.
A.2.1.9Heat exchangers, as follows:
(a)steam generators especially designed or prepared for the primary, or intermediate, coolant circuit of a nuclear reactor within the meaning of paragraph A.2.1.1; or
(b)other heat exchangers especially designed or prepared for use in the primary coolant circuit of a nuclear reactor within the meaning of paragraph A.2.1.1.
NOTE
Paragraph A.2.1.9 does not include the emergency cooling system or the decay heat cooling system.
A.2.1.10Neutron detectors
Especially designed or prepared neutron detectors for determining neutron flux levels within the core of a nuclear reactor within the meaning of paragraph A.2.1.1.
A.2.1.11External thermal shields
External thermal shields especially designed or prepared for use in a nuclear reactor within the meaning of paragraph A.2.1.1 for reduction of heat loss and for containment vessel protection.
A.2.2Plants for the reprocessing of irradiated fuel elements, and equipment especially designed or prepared for that purpose, including:
A.2.2.1Irradiated fuel element decladding equipment and chopping machines
Remotely operated equipment especially designed or prepared for use in reprocessing plants referred to in paragraph A.2.2 and intended to expose or prepare the irradiated nuclear material in fuel assemblies, bundles or rods for processing.
A.2.2.2Dissolver
Dissolver vessels or dissolvers employing mechanical devices especially designed or prepared for use in reprocessing plants referred to in paragraph A.2.2, intended for the dissolution of irradiated nuclear fuel and that are capable of withstanding hot, highly corrosive liquid, and that can be remotely loaded, operated and maintained.
A.2.2.3Solvent extractors and solvent extraction equipment
Especially designed or prepared solvent extractors such as packed or pulse columns, mixer settlers or centrifugal contactors for use in reprocessing plants referred to in paragraph A.2.2. Solvent extractors must be resistant to the corrosive effect of nitric acid. Solvent extractors are normally fabricated to extremely high standards (including special welding and inspection and quality assurance and quality control techniques) out of low carbon stainless steels, titanium, zirconium or other high-quality materials.
A.2.2.4Chemical holding or storage vessel
Especially designed or prepared holding or storage vessels for use in reprocessing plants referred to in paragraph A.2.2. The holding or storage vessels must be resistant to the corrosive effect of nitric acid. The holding or storage vessels are normally fabricated of materials such as low carbon stainless steels, titanium or zirconium, or other high-quality materials. Holding or storage vessels may be designed for remote operation and maintenance and may have the following features for control of nuclear criticality:
(a)walls or internal structures with a boron equivalent of at least 2%;
(b)a maximum diameter of 175 mm (7 in.) for cylindrical vessels; or
(c)a maximum width of 75 mm (3 in.) for either a slab or annular vessel.
A.2.2.5Neutron measurement systems for process control
Neutron measurement systems especially designed or prepared for integration and use with automated process control systems in reprocessing plants referred to in paragraph A.2.2.
A.2.2.6[Repealed, SOR/2010-106, s. 10]
A.2.3Plants for the fabrication of nuclear reactor fuel elements, and equipment especially designed or prepared for that purpose, including equipment that:
(a)normally comes in direct contact with, or directly processes, or controls, the production flow of nuclear material;
(b)seals the nuclear material within the cladding;
(c)checks the integrity of the cladding or the seal;
(d)checks the finish treatment of the sealed fuel; or
(e)is used for assembling reactor fuel elements.
NOTE
Such equipment or systems of equipment may include any of the following:
(a)fully automatic pellet inspection stations especially designed or prepared for checking final dimensions and surface defects of the fuel pellets;
(b)automatic welding machines especially designed or prepared for welding end caps onto the fuel pins (or rods);
(c)automatic test and inspection stations especially designed or prepared for checking the integrity of completed fuel pins (or rods);
(d)systems especially designed or prepared to manufacture nuclear fuel cladding.
A.2.4Plants for the separation of isotopes of natural uranium, depleted uranium or special fissionable material and equipment, other than analytical instruments, especially designed or prepared for that purpose, including
A.2.4.1Gas centrifuges and assemblies and components especially designed or prepared for use in gas centrifuges, including:
A.2.4.1.1Rotating components
(a)complete rotor assemblies:
thin-walled cylinders, or a number of interconnected thin-walled cylinders, manufactured from one or more of the high strength to density ratio materials. If interconnected, the cylinders are joined together by flexible bellows or rings as described in paragraph (c). The rotor is fitted with an internal baffle(s) and end caps, as described in paragraphs (d) and (e), if in final form. However the complete assembly may be delivered only partly assembled;
(b)rotor tubes:
especially designed or prepared thin-walled cylinders with a thickness of 12 mm or less, a diameter of between 75 mm and 650 mm, and manufactured from high strength to density ratio materials;
(c)rings or bellows:
components especially designed or prepared to give localized support to the rotor tube or to join together a number of rotor tubes. The bellows is a short cylinder with a wall thickness of 3 mm or less, a diameter of between 75 mm and 650 mm, having a convolute, and manufactured from high strength to density ratio materials;
(d)baffles:
disc-shaped components of between 75 mm and 650 mm in diameter especially designed or prepared to be mounted inside the centrifuge rotor tube, in order to isolate the take-off chamber from the main separation chamber and, in some cases, to assist the UF6 gas circulation within the main separation chamber of the rotor tube, and manufactured from high strength to density ratio materials; and
(e)top caps or bottom caps:
disc-shaped components of between 75 mm and 650 mm in diameter especially designed or prepared to fit to the ends of the rotor tube, and so contain the UF6 within the rotor tube, and in some cases to support, retain or contain as an integrated part an element of the upper bearing (top cap) or to carry the rotating elements of the motor and lower bearing (bottom cap), and manufactured from high strength to density ratio materials.
NOTE
The materials used for centrifuge rotating components include the following:
(a)maraging steel capable of an ultimate tensile strength of 1.95 GPa or more;
(b)aluminium alloys capable of an ultimate tensile strength of 0.46 GPa or more; and
(c)filamentary materials suitable for use in composite structures and having a specific modulus of 3.18 × 106 m or greater and a specific ultimate tensile strength of 7.62 × 104 m or greater (specific modulus is the Young’s Modulus in N/m2 divided by the specific weight in N/m3 and specific ultimate tensile strength is the ultimate tensile strength in N/m2 divided by the specific weight in N/m3).
A.2.4.1.2Static components
(a)magnetic suspension bearings:
(1)especially designed or prepared bearing assemblies consisting of an annular magnet suspended within a housing containing a damping medium. The housing will be manufactured from a UF6-resistant material. The magnet couples with a pole piece or a second magnet fitted to the top cap described in paragraph A.2.4.1.1(e). The annular magnet may have a relationship between an outer and inner diameter smaller or equal to 1.6:1. It may also be in a form having an initial permeability of 0.15 H/m or more, or a remanence of 98.5% or more, or an energy product of greater than 80 kJ/m3. In addition to the usual material properties, it is a prerequisite that the deviation of the magnetic axes from the geometrical axes is limited to very small tolerances (lower than 0.1 mm) or that homogeneity of the material of the magnet is specially called for; or
(2)active magnetic bearings especially designed or prepared for use in gas centrifuges;
(b)bearings/dampers:
especially designed or prepared bearings comprising a pivot/cup assembly mounted on a damper. The pivot is normally a hardened steel shaft with a hemisphere at one end with a means of attachment to the bottom cap described in paragraph A.2.4.1.1.(e) at the other. The shaft may however have a hydrodynamic bearing attached. The cup is pellet-shaped with a hemispherical indentation in one surface. These components are often supplied separately to the damper;
(c)molecular pumps:
especially designed or prepared cylinders having internally machined or extruded helical grooves and internally machined bores. Typical dimensions are as follows: 75 mm to 650 mm internal diameter, 10 mm or more wall thickness, with the length equal to or greater than the diameter. The grooves are typically rectangular in cross-section and 2 mm or more in depth;
(d)motor stators:
especially designed or prepared annular stators for high speed multiphase AC hysteresis (or reluctance) motors for synchronous operation within a vacuum at a frequency of 600 Hz or greater and a power of 40 VA or greater. The stators may consist of multiphase windings on a laminated low-loss iron core comprised of thin layers typically 2 mm thick or less;
(e)centrifuge housing or recipients:
components especially designed or prepared to contain the rotor tube assembly of a gas centrifuge. The housing consists of a rigid cylinder of wall thickness up to 30 mm with precision-machined ends to locate the bearings and with one or more flanges for mounting. The machined ends are parallel to each other and perpendicular to the cylinder’s longitudinal axis to within 0.05° or less. The housing may also be a honeycomb-type structure to accommodate several rotor assemblies; and
(f)scoops:
especially designed or prepared tubes for the extraction of UF6 gas from within the rotor tube by a Pitot tube action (that is, with an aperture facing into the circumferential gas flow within the rotor tube, for example by bending the end of a radially disposed tube) and capable of being fixed to the central gas extraction system.
A.2.4.2Especially designed or prepared auxiliary systems, equipment and components for gas centrifuge enrichment plants, including the following:
A.2.4.2.1Feed systems or product and tails withdrawal systems
Especially designed or prepared process systems or equipment for enrichment plants, made of or protected by materials resistant to corrosion by UF6 including
(a)feed autoclaves, ovens or systems used for passing UF6 to the enrichment process;
(b)desublimers, cold traps or pumps used to remove UF6 from the enrichment process for subsequent transfer upon heating;
(c)solidification or liquefaction stations used to remove UF6 from the enrichment process by compressing and converting UF6 to a liquid or solid form; and
(d)product and tails stations used for transferring UF6 into containers.
A.2.4.2.2Machine header piping systems
Especially designed or prepared piping systems and header systems for handling UF6 within the centrifuge cascades. The piping system is normally of the triple header type with each centrifuge connected to each of the headers. There is thus a substantial amount of repetition in its form. It is wholly made of or protected by UF6-resistant materials and is fabricated to very high vacuum and cleanliness standards.
A.2.4.2.3Special shut-off and control valves
(a)shut-off valves especially designed or prepared to act on the feed, product or tails UF6 gas streams of a gas centrifuge; or
(b)bellows-sealed valves, manual or automated shut-off or control, made of or protected by materials resistant to corrosion by UF6, with an inside diameter of 10 mm to 160 mm, especially designed or prepared for use in main or auxiliary systems of gas centrifuge enrichment plants.
A.2.4.2.4UF6 mass spectrometers with ion sources
Especially designed or prepared mass spectrometers capable of taking on-line samples from UF6 gas streams and having all of the following characteristics:
(a)the capability of measuring ions of 320 atomic mass units or greater with a resolution of better than 1 part in 320;
(b)ion sources made of or protected by nickel, nickel-copper alloys with a nickel content of 60% by weight or more, or nickel-chrome alloys;
(c)electron bombardment ionization sources; and
(d)a collector system suitable for isotopic analysis.
A.2.4.2.5Frequency changers
Frequency changers (also known as converters or inverters) especially designed or prepared to supply motor stators within the meaning of paragraph A.2.4.1.2(d), or parts, components and sub-assemblies of such frequency changers, having both of the following characteristics:
(a)a multiphase frequency output of 600 Hz or greater; and
(b)high stability (with frequency control better than 0.2%).
A.2.4.3Especially designed or prepared assemblies and components for use in gaseous diffusion enrichment, including:
A.2.4.3.1Gaseous diffusion barriers and barrier materials
(a)especially designed or prepared thin, porous filters, with a pore size of 10 nm to 100 nm, a thickness of 5 mm or less, and for tubular forms, a diameter of 25 mm or less, made of metallic, polymer or ceramic materials resistant to corrosion by UF6; and
(b)especially prepared compounds or powders for the manufacture of such filters. Such compounds and powders include nickel or alloys containing 60% by weight or greater nickel, aluminium oxide, or UF6-resistant fully fluorinated hydrocarbon polymers having a purity of 99.9% by weight or greater, a particle size less than 10 µm, and a high degree of particle size uniformity, which are especially prepared for the manufacture of gaseous diffusion barriers.
A.2.4.3.2Diffuser housings
Especially designed or prepared hermetically sealed cylindrical vessels for containing the gaseous diffusion barrier, made of or protected by UF6-resistant materials.
A.2.4.3.3Compressors and gas blowers
Especially designed or prepared compressors and gas blowers with a suction volume capacity of 1 m3/min or more of UF6 and a discharge pressure of up to 500 kPa, designed for long-term operation in the UF6 environment, as well as separate assemblies of such compressors and gas blowers. These compressors and gas blowers have a pressure ratio of 10:1 or less and are made of or protected by materials resistant to UF6.
A.2.4.3.4Rotary shaft seals
Especially designed or prepared vacuum seals, with seal feed and seal exhaust connections, for sealing the shaft connecting the compressor or the gas blower rotor with the driver motor so as to ensure a reliable seal against in-leaking of air into the inner chamber of the compressor or gas blower, which is filled with UF6. Such seals are normally designed for a buffer gas in-leakage rate of less than 1 000 cm3/min.
A.2.4.3.5Heat exchangers for cooling UF6
Especially designed or prepared heat exchangers made of or protected by UF6-resistant materials and intended for a leakage pressure change rate of less than 10 Pa/hour under a pressure difference of 100 kPa.
A.2.4.4Especially designed or prepared auxiliary systems, equipment and components for use in gaseous diffusion enrichment, including:
A.2.4.4.1Feed systems or product and tails withdrawal systems
Especially designed or prepared process systems or equipment for enrichment plants made of or protected by materials resistant to corrosion by UF6, including
(a)feed autoclaves, ovens or systems used for passing UF6 to the enrichment process;
(b)desublimers (or cold traps) or pumps used to remove UF6 from the enrichment process for subsequent transfer upon heating;
(c)solidification or liquefaction stations used to remove UF6 from the enrichment process by compressing and converting UF6 to a liquid or solid form; and
(d)product or tails stations used for transferring UF6 into containers.
A.2.4.4.2Header piping systems
Especially designed or prepared piping systems and header systems for handling UF6 within the gaseous diffusion cascades. This piping network is normally of the double header system with each cell connected to each of the headers.
A.2.4.4.3Vacuum systems
(a)especially designed or prepared vacuum manifolds, vacuum headers and vacuum pumps having a suction capacity of 5 m3/min or more; and
(b)vacuum pumps especially designed for service in UF6-bearing atmospheres, made of or protected by materials resistant to corrosion by UF6. These pumps may be either rotary or positive, may have displacement and fluorocarbon seals and may have special working fluids present.
A.2.4.4.4Special shut-off and control valves
Especially designed or prepared bellows-sealed valves, manual or automated, shut-off or control, made of or protected by materials resistant to corrosion by UF6, for installation in main and auxiliary systems of gaseous diffusion enrichment plants.
A.2.4.4.5UF6 mass spectrometers with ion sources
Especially designed or prepared mass spectrometers capable of taking on-line samples, from UF6 gas streams and having all of the following characteristics:
(a)the capability of measuring ions of 320 atomic mass units or greater with a resolution of better than 1 part in 320;
(b)ion sources constructed of or protected by nickel, nickel-copper alloys with a nickel content of 60% by weight or more, or nickel-chrome alloys;
(c)electron bombardment ionization sources; and
(d)a collector system suitable for isotopic analysis.
A.2.4.5Especially designed or prepared systems, equipment and components for use in aerodynamic enrichment plants, including:
A.2.4.5.1Separation nozzles
Especially designed or prepared separation nozzles and separation nozzle assemblies. The separation nozzles consist of slit-shaped, curved channels having a radius of curvature of less than 1 mm, resistant to corrosion by UF6 and having a knife-edge within the nozzle that separates the gas flowing through the nozzle into two fractions.
A.2.4.5.2Vortex tubes
Especially designed or prepared vortex tubes and vortex tube assemblies. The vortex tubes are cylindrical or tapered, made of or protected by materials resistant to corrosion by UF6, and with one or more tangential inlets. The tubes may be equipped with nozzle-type appendages at either or both ends.
A.2.4.5.3Compressors and gas blowers
Especially designed or prepared compressors or gas blowers made of or protected by materials resistant to corrosion by the UF6 carrier gas (hydrogen or helium) mixture.
A.2.4.5.4Rotary shaft seals
Especially designed or prepared rotary shaft seals, with seal feed and seal exhaust connections, for sealing the shaft connecting the compressor rotor or the gas blower rotor with the driver motor so as to ensure a reliable seal against out-leakage of process gas or in-leakage of air or seal gas into the inner chamber of the compressor or gas blower which is filled with a UF6/carrier gas mixture.
A.2.4.5.5Heat exchangers for gas cooling
Especially designed or prepared heat exchangers made of or protected by materials resistant to corrosion by UF6.
A.2.4.5.6Separation element housings
Especially designed or prepared separation element housings, made of or protected by materials resistant to corrosion by UF6, for containing vortex tubes or separation nozzles.
A.2.4.5.7Feed systems/product and tails withdrawal systems
Especially designed or prepared process systems or equipment for enrichment plants made of or protected by materials resistant to corrosion by UF6, including:
(a)feed autoclaves, ovens, or systems used for passing UF6 to the enrichment process;
(b)desublimers (or cold traps) used to remove UF6 from the enrichment process for subsequent transfer upon heating;
(c)solidification or liquefaction stations used to remove UF6 from the enrichment process by compressing and converting UF6 to a liquid or solid form; and
(d)product or tails stations used for transferring UF6 into containers.
A.2.4.5.8Header piping systems
Especially designed or prepared header piping systems, made of or protected by materials resistant to corrosion by UF6, for handling UF6 within the aerodynamic cascades. This piping network is normally of the double header design with each stage or group of stages connected to each of the headers.
A.2.4.5.9Vacuum systems and pumps
(a)especially designed or prepared vacuum systems, including vacuum manifolds, vacuum headers and vacuum pumps, designed for service in UF6-bearing atmospheres; and
(b)vacuum pumps especially designed or prepared for service in UF6-bearing atmospheres and made of or protected by materials resistant to corrosion by UF6. These pumps may use fluorocarbon seals and special working fluids.
A.2.4.5.10Special shut-off and control valves
Especially designed or prepared bellows-sealed valves, manual or automated, shut-off or control, made of or protected by materials resistant to corrosion by UF6 and with a diameter of 40 mm or greater, for installation in main and auxiliary systems of aerodynamic enrichment plants.
A.2.4.5.11UF6 mass spectrometers with ion sources
Especially designed or prepared mass spectrometers capable of taking on-line samples from UF6 gas streams and having all of the following characteristics:
(a)the capability of measuring ions of 320 atomic mass units or greater with a resolution of better than 1 part in 320;
(b)ion sources constructed of or protected by nickel, nickel-copper alloys with a nickel content of 60% by weight or more, or nickel-chrome alloys;
(c)electron bombardment ionization sources; and
(d)collector system suitable for isotopic analysis.
A.2.4.5.12UF6/carrier gas separation systems
Especially designed or prepared process systems for separating UF6 from carrier gas (hydrogen or helium).
A.2.4.6Especially designed or prepared systems, equipment and components for use in chemical exchange or ion exchange enrichment plants, including:
A.2.4.6.1Liquid-liquid exchange columns (chemical exchange)
Countercurrent liquid-liquid exchange columns with mechanical power input, especially designed or prepared for uranium enrichment using the chemical exchange process. For corrosion resistance to concentrated hydrochloric acid solutions, these columns and their internals are generally made of or protected by suitable plastic materials (such as fluorinated hydrocarbon polymers) or glass. The stage residence time of the columns is normally designed to be 30 s or less.
A.2.4.6.2Liquid-liquid centrifugal contactors (chemical exchange)
Liquid-liquid centrifugal contactors especially designed or prepared for uranium enrichment using the chemical exchange process. Such contactors use rotation to achieve dispersion of the organic and aqueous streams and then centrifugal force to separate the phases. For corrosion resistance to concentrated hydrochloric acid solutions, the contactors are generally made of or protected by suitable plastic materials (such as fluorinated hydrocarbon polymers) or glass. The stage residence time of the centrifugal contactors is normally designed to be 30 s or less.
A.2.4.6.3Uranium reduction systems and equipment (chemical exchange)
(a)especially designed or prepared electrochemical reduction cells to reduce uranium from one valence state to another for uranium enrichment using the chemical exchange process. The cell materials in contact with process solutions must be corrosion resistant to concentrated hydrochloric acid solutions; and
(b)especially designed or prepared systems at the product end of the cascade for taking the U+4 out of the organic stream, adjusting the acid concentration and feeding to the electrochemical reduction cells.
A.2.4.6.4Feed preparation systems (chemical exchange)
Especially designed or prepared systems for producing high-purity uranium chloride feed solutions for chemical exchange uranium isotope separation plants.
A.2.4.6.5Uranium oxidation systems (chemical exchange)
Especially designed or prepared systems for oxidation of U+3 to U+4 for return to the uranium isotope separation cascade in the chemical exchange enrichment process.
A.2.4.6.6Fast-reacting ion exchange resins/adsorbents (ion exchange)
Fast-reacting ion-exchange resins or adsorbents especially designed or prepared for uranium enrichment using the ion exchange process, including porous macroreticular resins, and pellicular structures in which the active chemical exchange groups are limited to a coating on the surface of an inactive porous support structure, and other composite structures in any suitable form including particles or fibres. These ion exchange resins/adsorbents have diameters of 0.2 mm or less and must be chemically resistant to concentrated hydrochloric acid solutions as well as physically strong enough so as not to degrade in the exchange columns. The resins/adsorbents are especially designed to achieve very fast uranium isotope exchange kinetics (exchange rate half-time of less than 10 s) and are capable of operating at a temperature in the range of 100°C to 200°C.
A.2.4.6.7Ion exchange columns (ion exchange)
Cylindrical columns greater than 1 000 mm in diameter for containing and supporting packed beds of ion exchange resin/adsorbent, especially designed or prepared for uranium enrichment using the ion exchange process. These columns are made of or protected by materials (such as titanium or fluorocarbon plastics) resistant to corrosion by concentrated hydrochloric acid solutions and are capable of operating at a temperature in the range of 100°C to 200°C and pressures above 0.7 MPa (102 psi).
A.2.4.6.8Ion exchange reflux systems (ion exchange)
(a)especially designed or prepared chemical or electrochemical reduction systems for regeneration of the chemical reducing agent(s) used in ion exchange uranium enrichment cascades; and
(b)especially designed or prepared chemical or electrochemical oxidation systems for regeneration of the chemical oxidizing agent(s) used in ion exchange uranium enrichment cascades.
A.2.4.7Especially designed or prepared systems, equipment and components for use in laser-based enrichment plants, including:
A.2.4.7.1Uranium vaporization systems (Atomic Vapour Laser Isotope Separation)
Especially designed or prepared uranium vaporization systems for use in laser enrichment.
A.2.4.7.2Liquid or vapour uranium metal handling systems and components (Atomic Vapour Laser Isotope Separation)
Especially designed or prepared systems for handling molten uranium, molten uranium alloys or uranium metal vapour for use in laser enrichment, or especially designed or prepared components for that purpose.
A.2.4.7.3Uranium metal product and tails collector assemblies (Atomic Vapour Laser Isotope Separation)
Especially designed or prepared product and tails collector assemblies for collecting uranium metal in liquid or solid form.
A.2.4.7.4Separator module housings (Atomic Vapour Laser Isotope Separation)
Especially designed or prepared cylindrical or rectangular vessels for containing the uranium metal vapour source, the electron beam gun, and the product and tails collectors.
A.2.4.7.5Supersonic expansion nozzles (Molecular Laser Isotope Separation)
Especially designed or prepared supersonic expansion nozzles for cooling mixtures of UF6 and carrier gas to 150 K (-123°C) or less and that are corrosion resistant to UF6.
A.2.4.7.6Product or tails collectors (Molecular Laser Isotope Separation)
Especially designed or prepared components or devices for collecting uranium product material or uranium tails material following illumination with laser light.
A.2.4.7.7UF6/carrier gas compressors (molecular laser isotope separation)
Especially designed or prepared compressors for UF6/carrier gas mixtures, designed for long-term operation in a UF6 environment. The components of these compressors that come into contact with process gas are made of or protected by materials resistant to corrosion by UF6.
A.2.4.7.8Rotary shaft seals (molecular laser isotope separation)
Especially designed or prepared rotary shaft seals, with seal feed and seal exhaust connections, for sealing the shaft connecting the compressor rotor with the driver motor so as to ensure a reliable seal against out-leakage of process gas or in-leakage of air or seal gas into the inner chamber of the compressor which is filled with a UF6/carrier gas mixture.
A.2.4.7.9Fluorination systems (molecular laser isotope separation)
Especially designed or prepared systems for fluorinating UF5 (solid) to UF6 (gas).
A.2.4.7.10UF6 mass spectrometers with ion sources (Molecular Laser Isotope Separation)
Especially designed or prepared mass spectrometers capable of taking on-line samples from UF6 gas streams and having all of the following characteristics:
(a)the capability of measuring ions of 320 atomic mass units or greater with a resolution of better than 1 part in 320;
(b)ion sources constructed of or protected by nickel, nickel-copper alloys with a nickel content of 60% by weight or more, or nickel-chrome alloys;
(c)electron bombardment ionization sources; and
(d)collector system suitable for isotopic analysis.
A.2.4.7.11Feed systems/product and tails withdrawal systems (molecular laser isotope separation)
Especially designed or prepared process systems or equipment for enrichment plants made of or protected by materials resistant to corrosion by UF6, including:
(a)feed autoclaves, ovens, or systems used for passing UF6 to the enrichment process;
(b)desublimers (or cold traps) used to remove UF6 from the enrichment process for subsequent transfer upon heating;
(c)solidification or liquefaction stations used to remove UF6 from the enrichment process by compressing and converting UF6 to a liquid or solid form; and
(d)product or tails stations used for transferring UF6 into containers.
A.2.4.7.12UF6/carrier gas separation systems (molecular laser isotope separation)
Especially designed or prepared process systems for separating UF6 from carrier gas. The carrier gas may be nitrogen, argon, or other gas.
A.2.4.7.13Laser systems
Lasers or laser systems especially designed or prepared for the separation of uranium isotopes.
A.2.4.8Especially designed or prepared systems, equipment and components for use in plasma separation enrichment plants, including:
A.2.4.8.1Microwave power sources and antennae
Especially designed or prepared microwave power sources and antennae for producing or accelerating ions and having the following characteristics: greater than 30 GHz frequency and greater than 50 kW mean power output for ion production.
A.2.4.8.2Ion excitation coils
Especially designed or prepared radio frequency ion excitation coils for frequencies of more than 100 kHz and capable of handling more than 40 kW mean power.
A.2.4.8.3Uranium plasma generation systems
Especially designed or prepared systems for the generation of uranium plasma for use in plasma separation plants.
A.2.4.8.4[Repealed, SOR/2025-196, s. 34]
A.2.4.8.5Uranium metal product and tails collector assemblies
Especially designed or prepared product and tails collector assemblies for uranium metal in solid form. These collector assemblies are made of or protected by materials resistant to the heat and corrosion of uranium metal vapour, such as yttria-coated graphite or tantalum.
A.2.4.8.6Separator module housings
Cylindrical vessels especially designed or prepared for use in plasma separation enrichment plants for containing the uranium plasma source, radio-frequency drive coil and the product and tails collectors.
A.2.4.9Especially designed or prepared systems, equipment and components for use in electromagnetic enrichment plants, including:
A.2.4.9.1Electromagnetic isotope separators
Electromagnetic isotope separators especially designed or prepared for the separation of uranium isotopes, and equipment and components therefor, including:
(a)ion sources:
especially designed or prepared single or multiple uranium ion sources consisting of a vapour source, ionizer, and beam accelerator, constructed of suitable materials such as graphite, stainless steel, or copper, and capable of providing a total ion beam current of 50 mA or greater;
(b)ion collectors:
collector plates consisting of two or more slits and pockets especially designed or prepared for collection of enriched and depleted uranium ion beams and constructed of suitable materials such as graphite or stainless steel;
(c)vacuum housings:
especially designed or prepared vacuum housings for uranium electromagnetic separators, constructed of suitable non-magnetic materials such as stainless steel and designed for operation at pressures of 0.1 Pa or lower; and
(d)magnet pole pieces:
especially designed or prepared magnet pole pieces having a diameter greater than 2 m used to maintain a constant magnetic field within an electromagnetic isotope separator and to transfer the magnetic field between adjoining separators.
A.2.4.9.2High voltage power supplies
Especially designed or prepared high-voltage power supplies for ion sources, having all of the following characteristics: capable of continuous operation, output voltage of 20 000 V or greater, output current of 1 A or greater, and voltage regulation of better than 0.01% over a time period of 8 hours.
A.2.4.9.3Magnet power supplies
Especially designed or prepared high-power, direct current magnet power supplies having all of the following characteristics: capable of continuously producing a current output of 500 A or greater at a voltage of 100 V or greater and with a current or voltage regulation better than 0.01% over a period of 8 hours.
A.2.5Plants for the production or concentration of heavy water, deuterium and deuterium compounds and equipment especially designed or prepared therefor, including:
A.2.5.1Water-hydrogen sulphide exchange towers
Exchange towers with diameters of 1.5 m or greater and capable of operating at pressures greater than or equal to 2 MPa, especially designed or prepared for heavy water production utilizing the water-hydrogen sulphide exchange process.
A.2.5.2Blowers and compressors
Single stage, low head (i.e., 0.2 MPa) centrifugal blowers or compressors for hydrogen sulphide gas circulation (i.e., gas containing more than 70% by weight of hydrogen sulphide), especially designed or prepared for heavy water production utilizing the water-hydrogen sulphide exchange process. These blowers or compressors have a throughput capacity greater than or equal to 56 m3/s while operating at pressures greater than or equal to 1.8 MPa suction and have seals designed for wet hydrogen sulphide service.
A.2.5.3Ammonia-hydrogen exchange towers
Ammonia-hydrogen exchange towers greater than or equal to 35 m in height with diameters of 1.5 m to 2.5 m and capable of operating at pressures greater than 15 MPa, especially designed or prepared for heavy water production utilizing the ammonia-hydrogen exchange process. These towers also have at least one flanged, axial opening of the same diameter as the cylindrical part through which the internals can be inserted or withdrawn.
A.2.5.4Tower internals and stage pumps
Tower internals and stage pumps especially designed or prepared for towers for heavy water production utilizing the ammonia-hydrogen exchange process. Tower internals include especially designed stage contactors which promote intimate gas/liquid contact. Stage pumps include especially designed submersible pumps for circulation of liquid ammonia within a contacting stage internal to the stage towers.
A.2.5.5Ammonia crackers
Ammonia crackers with operating pressures greater than or equal to 3 MPa (450 psi) especially designed or prepared for heavy water production utilizing the ammonia-hydrogen exchange process.
A.2.5.6Infrared absorption analyzers
Infrared absorption analyzers capable of on-line hydrogen to deuterium ratio analysis if deuterium concentrations are equal to or greater than 90% by weight.
A.2.5.7Catalytic burners
Catalytic burners for the conversion of enriched deuterium gas into heavy water especially designed or prepared for heavy water production utilizing the ammonia-hydrogen exchange process.
A.2.5.8Complete heavy water upgrade systems or columns for those systems
Complete heavy water upgrade systems, or columns for them, especially designed or prepared for the upgrade of heavy water to reactor-grade deuterium concentration.
A.2.5.9Ammonia synthesis converters or synthesis units
Ammonia synthesis converters or synthesis units especially designed or prepared for heavy water production utilizing the ammonia-hydrogen exchange process.
A.2.6Plants for the conversion of uranium and plutonium for use in the fabrication of fuel elements and the separation of uranium isotopes, as set out in paragraphs A.2.3. and A.2.4., respectively, and equipment especially designed or prepared for such plants, including
A.2.6.1Plants for the conversion of uranium and equipment especially designed or prepared for that purpose, including
A.2.6.1.1Especially designed or prepared systems for the conversion of uranium ore concentrates to UO3.
A.2.6.1.2Especially designed or prepared systems for the conversion of UO3 to UF6.
A.2.6.1.3Especially designed or prepared systems for the conversion of UO3 to UO2.
A.2.6.1.4Especially designed or prepared systems for the conversion of UO2 to UF4.
A.2.6.1.5Especially designed or prepared systems for the conversion of UF4 to UF6.
A.2.6.1.6Especially designed or prepared systems for the conversion of UF4 to U metal.
A.2.6.1.7Especially designed or prepared systems for the conversion of UF6 to UO2.
A.2.6.1.8Especially designed or prepared systems for the conversion of UF6 to UF4.
A.2.6.1.9Especially designed or prepared systems for the conversion of UO2 to UCl4.
A.2.6.2Plants for the conversion of plutonium and equipment especially designed or prepared for that purpose, including
A.2.6.2.1Especially designed or prepared systems for the conversion of plutonium nitrate to oxide.
A.2.6.2.2Especially designed or prepared systems for plutonium metal production.
A.3. Parts for Controlled Nuclear Equipment Identified in Paragraphs Comprising A.2.NOTE
Paragraph A.3 includes parts designed or prepared for controlled nuclear equipment identified in paragraphs comprising A.2.
A.4. Controlled Nuclear Information A.4.1Technology
Technical data for the design, production, construction, operation or maintenance of any item in this part, including, but not limited to, blueprints, plans, diagrams, models, formulae, engineering designs and specifications, software, manuals and instructions, except data available to the public (e.g., publications, publicly available websites, or that which has been made available without restrictions on its further dissemination).
NOTE
Technical data referred to in paragraph A.4.1 is subject to control under both tangible and intangible modes of transfer.
PART BList of Nuclear-related Dual-use ItemsB.1. Controlled Nuclear Substances B.1.1Nuclear-related dual-use substances
B.1.1.1Radionuclides appropriate for making neutron sources based on alpha-n reaction as follows:
(a)actinium-225 (225Ac);
(b)actinium-227 (227Ac);
(c)californium-253 (253Cf);
(d)curium-240 (240Cm);
(e)curium-241 (241Cm);
(f)curium-242 (242Cm);
(g)curium-243 (243Cm);
(h)curium-244 (244Cm);
(i)einsteinium-253 (253Es);
(j)einsteinium-254 (254Es);
(k)gadolinium-148 (148Gd);
(l)plutonium-236 (236Pu);
(m)plutonium-238 (238Pu);
(n)polonium-208 (208Po);
(o)polonium-209 (209Po);
(p)polonium-210 (210Po);
(q)radium-223 (223Ra);
(r)thorium-227 (227Th);
(s)thorium-228 (228Th);
(t)uranium-230 (230U); and
(u)uranium-232 (232U).
NOTE
These radionuclides may be in elemental form or may be contained in:
(a)compounds having a total radioactivity of 37 GBq/kg or greater;
(b)mixtures having a total radioactivity of 37 GBq/kg or greater;
(c)products or devices containing anything referred to in paragraphs (a) and (b), except a product or device containing a compound or mixture having a total radioactivity of less than 3.7 GBq; or
(d)products or devices containing radionuclides in elemental form, except a product or device having a total radioactivity of less than 3.7 GBq.
B.1.1.2Aluminium alloys capable of an ultimate tensile strength of 0.46 GPa or more at 293 K, in the form of tubes or cylindrical solid forms (including forgings) with an outside diameter of more than 75 mm.
NOTE
The phrase “capable of” encompasses aluminium alloys before or after heat treatment.
B.1.1.3Beryllium metal, alloys containing more than 50% beryllium by weight, beryllium compounds, and manufactures thereof, except:
(a)metal windows for X-ray machines, or for bore-hole logging devices;
(b)oxide shapes in fabricated or semi-fabricated forms specially designed for electronic component parts or as substrates for electronic circuits; and
(c)beryl (silicate of beryllium and aluminium) in the form of emeralds or aquamarines.
NOTE
This entry includes waste and scrap containing beryllium as defined above.
B.1.1.4Bismuth having both of the following characteristics:
(a)a purity of 99.99% or greater by weight;
(b)a silver content of less than 10 ppm by weight.
B.1.1.5Boron and boron compounds, mixtures, loaded materials, and waste or scrap of any of these substances, in which the boron-10 isotope is more than 20% by weight of the total boron content.
B.1.1.6Calcium (high purity) containing both less than 1 000 ppm by weight of metallic impurities other than magnesium and less than 10 ppm of boron.
B.1.1.7Chlorine trifluoride (ClF3).
B.1.1.8Crucibles made of materials resistant to liquid actinide metals, as follows:
(a)crucibles with a volume of between 150 ml and 8 L and made of or coated with any of the following materials having a purity of 98% or greater:
(1)calcium fluoride (CaF2)
(2)calcium zirconate (metazirconate) (Ca2ZrO3)
(3)cerium sulfide (Ce2S3)
(4)erbium oxide (erbia) (Er2O3)
(5)hafnium oxide (hafnia) (HfO2)
(6)magnesium oxide (MgO)
(7)nitrided niobium-titanium-tungsten alloy (approximately 50%Nb, 30%Ti, 20%W)
(8)yttrium oxide (yttria) (Y2O3)
(9)zirconium oxide (zirconia) (ZrO2);
(b)crucibles with a volume of between 50 ml and 2 L and made of or lined with tantalum, having a purity of 99.9% or greater; and
(c)crucibles with a volume of between 50 ml and 2 L and made of or lined with tantalum (having a purity of 98% or greater) coated with tantalum carbide, nitride, or boride (or any combination of these).
B.1.1.9Fibrous or filamentary materials, prepregs and composite structures, as follows:
(a)carbon or aramid fibrous or filamentary materials having a specific modulus of 12.7 x 106 m or greater or a specific tensile strength of 23.5 x 104 m or greater, except aramid fibrous or filamentary materials having 0.25% or more by weight of an ester based fibre surface modifier;
(b)glass fibrous or filamentary materials having a specific modulus of 3.18 x 106 m or greater and a specific tensile strength of 7.62 x 104 m or greater; and
(c)thermoset resin impregnated continuous yarns, rovings, tows or tapes with a width no greater than 15 mm (prepregs), made from carbon or glass fibrous or filamentary materials specified in paragraph (a) or (b).
NOTE
The resin forms the matrix of the composite.
(d)composite structures in the form of tubes with an inside diameter of between 75 mm (3 in.) and 400 mm (16 in.) made with any of the fibrous or filamentary materials specified in paragraph (a) or carbon prepreg materials specified in paragraph (c).
NOTE
(a)fibrous or filamentary materials means continuous monofilaments, yarns, rovings, tows or tapes.
(b)specific modulus is the Young’s modulus in N/m2 divided by the specific weight in N/m3 when measured at a temperature of 23 ± 2°C and a relative humidity of 50 ± 5%.
(c)specific tensile strength is the ultimate tensile strength in N/m2 divided by the specific weight in N/m3 when measured at a temperature of 23 ± 2°C and a relative humidity of 50 ± 5%.
B.1.1.10Hafnium metal, alloys, compounds of hafnium containing more than 60% hafnium by weight, and their manufactures, and waste or scrap of any of these substances.
B.1.1.11Helium-3 or mixtures, products or devices containing helium-3, except a product or device containing less than 1 g of helium-3.
B.1.1.12Lithium having any of the following characteristics:
(a)enriched in the lithium-6 isotope (6Li) to greater than 7.5 atom percent;
(b)enriched in the lithium-6 isotope contained in alloys, compounds, mixtures, waste or scrap;
(c)conforming to the description in paragraph (a) or (b) and contained in products or devices, except thermoluminescent dosimeters.
NOTE
The natural occurrence of the 6 isotope in lithium is 7.5 atom per cent.
B.1.1.13Magnesium (high purity) containing both less than 200 ppm by weight of metallic impurities other than calcium and less than 10 ppm of boron.
B.1.1.14Maraging steel capable of an ultimate tensile strength of 1 950 MPa or more at 293 K, except forms in which no linear dimension exceeds 75 mm.
NOTE
The phrase “capable of” encompasses maraging steel before or after heat treatment.
B.1.1.15Nickel powder and porous nickel metal, as follows:
(a)powder with a nickel purity content of 99% or greater and a mean particle size of less than 10 µm measured by the ASTM B 330 standard, except filamentary nickel powders; and
NOTE
Nickel powders which are specially prepared for the manufacture of gaseous diffusion barriers are controlled under paragraph A.2.4.3.1.(b).
(b)porous nickel metal produced from materials referred to in paragraph (a), except single porous nickel metal sheets not exceeding 1 000 cm2 per sheet.
NOTE
This refers to porous metal formed by compacting and sintering the material referred to in paragraph (a) to form a metal material with fine pores interconnected throughout the structure.
B.1.1.16Radium-226, radium-226 alloys, radium-226 compounds, or mixtures containing radium-226, products manufactured from them and products or devices containing any of them, except medical applicators and a product or device containing not more than 0.37 GBq of radium-226 in any form.
B.1.1.17Titanium alloys capable of an ultimate tensile strength of 900 MPa or more at 293 K in the form of tubes or cylindrical solid forms (including forgings) with an outside diameter of more than 75 mm.
NOTE
The phrase “capable of” encompasses titanium alloys before or after heat treatment.
B.1.1.18Tungsten, tungsten carbide, or tungsten alloys (greater than 90% tungsten by weight) having a mass greater than 20 kg and in forms with a hollow cylindrical symmetry (including cylinder segments) with an inside diameter between 100 mm and 300 mm, except parts specifically designed for use as weights or gamma-ray collimators.
B.1.1.19Zirconium with a hafnium content of less than 1 part hafnium to 500 parts zirconium by weight, in the form of metal, alloys containing more than 50% zirconium by weight, and compounds and manufactur
The text continues in the official source.
