LEGALDIGMLEGALDIGM
    ← Canada
    Beta
    C.R.C., c. 1171:en

    C.R.C., c. 1171:en — Regulations Respecting Railway Safety Appliance Standards

    Beta. Legal information, not legal advice. LEGALDIGM is not a law firm. Check the official source for the current text.

    Analyze this law with AI
    1 These Regulations may be cited as the Railway Safety Appliance Standards Regulations. 2 These Regulations apply to all rolling stock constructed or reconstructed and used on railways owned and operated by railway companies subject to the jurisdiction of the Commission. 3 Notwithstanding section 2, (a) sections 1 to 112 of Schedule I apply in respect of box and other house cars built or rebuilt prior to October 1, 1966; and (b) sections 112.1 to 112.44 of Schedule I shall apply in respect of box and other house cars built or rebuilt on and after October 1, 1966, or under construction prior thereto. 4 Sections 112.1 to 112.44 of Schedule I apply to all box and other house cars in service after December 31, 1982. 5 Notwithstanding section 1 and sections 316 to 349 of Schedule I, sections 349.1 to 349.20 of Schedule I apply to (a) all caboose cars with platforms built new or rebuilt after January 1, 1967; and (b) all caboose cars with platforms in service after December 31, 1982. 6 (1) Every railway company shall submit to the secretary of the Railway Transport Committee (a) before September 1, 1974, (i) information respecting the total number and types of cars and caboose cars with platforms that will require modification by virtue of section 4 and paragraph 5(b), and (ii) the time schedule fixed by the company for the making of any such modification; and (b) progress reports on the railway company’s compliance with the time schedule referred to in subparagraph (a)(ii), including information respecting the total number and type of the cars and caboose cars with platforms that remains to be modified (i) before August 1, 1980, for the period commencing on July 1, 1979 and ending on June 30, 1980, (ii) before February 1, 1981, for the period commencing on July 1, 1980 and ending on December 31, 1980, (iii) before August 1, 1981, for the period commencing on January 1, 1981 and ending on June 30, 1981, (iv) before February 1, 1982 for the period commencing on July 1, 1981 and ending on December 31, 1981, and (v) before August 1, 1982 for the period commencing on January 1, 1982 and ending on June 30, 1982. (2) Every railway company shall, not later than February 1, 1983, submit to the Secretary of the Railway Transport Committee a final report containing information respecting (a) the total number of cars and caboose cars with platforms that have been modified as required by virtue of section 4 and paragraph 5(b); and (b) the action that has been taken in respect of any cars or caboose cars with platforms that have not been modified for the reason that they are not in service. (3) No railway company shall put in service any car or caboose car with platform that has not been modified as required by virtue of section 4 or paragraph 5(b). SCHEDULE I(ss. 3, 4 and 5)Box and other House CarsHand BrakesNumber 1 (1)Each box or other house car shall be equipped with an efficient hand brake which shall operate in harmony with the power brake thereon. (2)The hand brake may be of any efficient design, but shall provide the same degree of safety as the design shown on Plate A of Schedule II. Dimensions 2 (1)The brake shaft shall be not less than 1 1/4 inches in diameter, of wrought iron or steel without weld. (2)The brake wheel may be flat or dished, not less than 15, preferably 16, inches in diameter, of malleable iron, wrought iron or steel. Location 3 (1)The hand brake shall be so located that it can be safely operated while the car is in motion. (2)The brake shaft shall be located on the end of the car to the left of and not less than 17 nor more than 22 inches from the centre. Manner of Application 4 (1)There shall be not less than four inches clearance around rim of brake wheel. (2)Outside edge of brake wheel shall be not less than four inches from a vertical plane parallel with end of car and passing through the inside face of knuckle when closed with coupler horn against the buffer block or end sill. (3)Top brake shaft support shall be fastened with not less than 1/2-inch bolts or rivets (See Plate A of Schedule II). (4)A brakeshaft step (a)shall support the lower end of the brake shaft; (b)which will permit the brake chain to drop under the brake shaft shall not be used; and (c)in a u-shaped form is preferred (See Plate A of Schedule II). (5)Brake shaft shall be arranged with a square fit at its upper end to secure the hand brake wheel; said square fit shall be not less than 7/8 inch square. Square-fit taper; nominally 2 in 12 inches (See Plate A of Schedule II). (6)Brake chain shall be of not less than 3/8, preferably 7/16 inch wrought iron or steel, with a link on the brake rod end of not less than 7/16, preferably 1/2 inch wrought iron or steel, and shall be secured to brake shaft drum by not less than 1/2 inch hexagon or square-headed bolt. Nut on said bolt shall be secured by riveting end of bolt over nut (See Plate A of Schedule II). (7)Lower end of brake shaft shall be provided with a trunnion of not less than 3/4, preferably one inch in diameter extending through brake shaft step and held in operating position by a suitable cotter or ring (See Plate A of Schedule II). (8)Brake shaft drum shall be not less than 1 1/2 inches in diameter (See Plate A of Schedule II). (9)Brake ratchet wheel shall be secured to brake shaft by a key or square fit; said square fit shall be of not less than 1 5/16 inches square. (10)When ratchet wheel with square fit is used provision shall be made to prevent ratchet wheel from rising on shaft to disengage brake pawl (See Plate A of Schedule II). (11)Brake ratchet wheel shall be not less than 5 1/4, preferably 5 1/2 inches in diameter and shall have not less than 14, preferably 16 teeth (See Plate A of Schedule II). (12)If brake ratchet wheel is more than 36 inches from brake wheel, a brake shaft support shall be provided to support this extended upper portion of brake shaft; said brake shaft support shall be fastened  with not less than 1/2-inch bolts or rivets. (13)The brake pawl shall be pivoted (a)upon a bolt or rivet not less than 5/8 inch in diameter; or (b)upon a trunnion secured by not less than 1/2-inch bolt or rivet. (14)Where the brake pawl is pivoted as provided under paragraph (a) or (b), there shall be a rigid metal connection between brake shaft and pivot of pawl. (15)Brake wheel shall be held in position on brake shaft by a nut on a threaded extended end of brake-shaft; said threaded portion shall be not less than 3/4 inch in diameter; said nut shall be secured by riveting over or by the use of a lock nut or suitable cotter. (16)Brake wheel shall be arranged with a square fit for brake shaft in hub of said wheel; taper of said fit, nominally 2 in 12 inches (See Plate A of Schedule II). Brake Step 5 (1)If brake step is used, it shall be not less than 28 inches in length. (2)Outside edge shall be not less than eight inches from face of car and not less than four inches from a vertical plane parallel with end of car and passing through the inside face of knuckle when closed with coupler horn against the bufferblock or end sill. Manner of Application 6Brake step shall be supported by not less than two metal braces having a minimum cross-sectional area 3/8 by 1 1/2 inches or equivalent, which shall be securely fastened to body of car with not less than 1/2-inch bolts or rivets. Running BoardsNumber 7 (1)One longitudinal running board. (2)On outside-metal roof cars, two latitudinal extensions. Dimensions 8 (1)Longitudinal running board shall be not less than 18, preferably 20, inches in width. (2)Latitudinal extensions shall be not less than 24 inches in width. Location 9 (1)Full length of car, centre of roof. (2)On outside-metal roof cars there shall be two latitudinal extensions from longitudinal running board to ladder locations, except on refrigerator cars where such latitudinal extensions cannot be applied on account of ice hatches. Manner of Application 10 (1)Running boards shall be continuous from end to end and not cut or hinged at any point; the length and width of runningboards may, however, be made up of a number of pieces securely fastened to saddle blocks with screws or bolts. (2)The ends of longitudinal running boards shall be not less than six nor more than 10 inches from a vertical plane parallel with end of car and passing through the inside face of knuckle when closed with coupler horn against the buffer block or end sill; and if more than four inches from edge of roof of car, shall be securely supported their full width by substantial metal braces. (3)Running boards shall be made of wood and securely fastened to car. (4)Notwithstanding subsection (3) but subject to the following conditions, running boards may be of a material other than wood if (a)the material and design is of a type accepted by the A.A.R. and approved by the Commission; and (b)the construction and installation is in accordance with A.A.R. requirements and acceptable to the Commission. Sill StepsNumber 11Six. Dimensions 12 (1)Minimum cross-sectional area 1/2 inch by 1 1/2 inches, or equivalent, of wrought iron or steel. (2)Minimum length of tread, 10, preferably 12, inches. (3)Minimum clear depth, eight inches. Location 13 (1)One near each end on each side of car, so that there shall be not more than 18 inches from end of car to centre of tread of sill step. (2)One at each end of car, centre of sill step to be as nearly central with the ladder as possible. (3)Outside edge of tread of step shall be not more than four inches inside of face of side of car, preferably flush with side of car. (4)Tread shall be not more than 24, preferably not more than 22, inches above the top of rail. Manner of Application 14 (1)Sill steps exceeding 21 inches in depth shall have an additional tread. (2)Sill steps shall be securely fastened with not less than 1/2-inch bolts with nuts outside (when possible) and riveted over, or with not less than 1/2-inch rivets. LaddersNumber 15Four. Dimensions 16 (1)Minimum clear length of tread: (a)side ladders, 16 inches; and (b)end ladders, 14 inches. (2)Maximum spacing between ladder treads, 19 inches. (3)Top ladder tread shall be located not less than 12 nor more than 18 inches from roof at eaves. (4)Spacing of side ladder treads shall be uniform within a limit of two inches from top ladder tread to bottom tread of ladder. (5)Maximum distance from bottom tread of side ladder to top tread of sill step, 21 inches. (6)End ladder treads (a)shall, where construction of car permits, be spaced to coincide with treads of side ladders, a variation of two inches being allowed; and (b)where construction of car will not permit the application of a tread of end ladder to coincide with bottom tread of side ladder, the bottom tread of end ladder shall coincide with second tread from bottom of side ladder. (7)Hard wood treads, minimum dimensions 1 1/2 by two inches. (8)Iron or steel treads, minimum diameter 5/8 inch. (9)Minimum clearance of treads, two, preferably 2 1/2, inches. Location 17Ladders shall be located (a)one on each side, not more than eight inches from right end of car, and (b)one on each end, not more than eight inches from left side of car, measured from inside edge of ladder-stile or clearance of ladder treads to corner of car. Manner of Application 18 (1)Metal ladders without stiles near corners of cars shall have foot guards or upward projections not less than two inches in height near inside end of bottom treads. (2)Stiles of ladders, projecting two or more inches from face of car, will serve as foot guards. (3)Ladders shall be securely fastened with not less 1/2-inch bolts with nuts outside (when possible) and riveted over, or with not less than 1/2-inch rivets; 3/8-inch bolts may be used for wooden treads that are gained into stiles. End Ladder Clearance 19No part of car above end sills within 30 inches from side of car, except buffer block, brake shaft, brake wheel, brake step, running board or uncoupling lever shall extend to within 12 inches of a vertical plane parallel with end of car and passing through the inside face of knuckle when closed with coupler horn against the buffer block, or end sill, and no other part of end of car or fixtures on same above end sills, other than exceptions herein noted, shall extend beyond the outer face of buffer block. Roof HandholdsNumber 20 (1)One over each ladder. (2)One right-angle handhold may take the place of two adjacent specified roof handholds, if the dimensions and locations coincide, and an extra leg is securely fastened to car at point of angle. Dimensions 21 (1)Minimum diameter, 5/8 inch, wrought iron or steel. (2)Minimum clear length, 16 inches. (3)Minimum clearance, two, preferably 2 1/2, inches. Location 22On roof of car: one parallel to treads of each ladder, not less than eight nor more than 15 inches from edge of roof, except that on refrigerator cars, where ice hatches prevent, the location may be nearer edge of roof. Manner of Application 23Roof handholds shall be securely fastened with not less than 1/2-inch bolts with nuts outside (when possible) and riveted over, or with not less than 1/2-inch rivets. Side HandholdsNumber 24Four. (Tread of side ladder is a side handhold) Dimensions 25 (1)Minimum diameter, 5/8 inch, wrought iron or steel. (2)Minimum clear length, 16 inches, preferably 24 inches. (3)Minimum clearance, two, preferably 2 1/2, inches. Location 26 (1)Horizontal: one near each end on each side of car. (2)Side handholds shall be not less than 24 nor more than 30 inches above centre line of coupler, except as provided above, where tread of ladder is a handhold. (3)Clearance of outer end of handhold shall be not more than eight inches from end of car. Manner of Application 27Side handholds shall be securely fastened with not less than 1/2-inch bolts with nuts outside (when possible) and riveted over or with not less than 1/2-inch rivets. Horizontal End HandholdsNumber 28Eight or more. (Four on each end of car.) (Tread of end ladder is an end handhold.) Dimensions 29 (1)Minimum diameter, 5/8 inch, wrought iron or steel. (2)Minimum clear length, 16 inches, preferably 24 inches. (3)Notwithstanding subsection (2), a handhold 14 inches in length may be used where it is impossible to use one 16 inches in length. (4)Minimum clearance, two, preferably 2 1/2, inches. Location 30 (1)One near each side on each end of car, not less than 24 nor more than 30 inches above centre line of coupler, except as provided above, when tread of end ladder is an end handhold. (2)Clearance of outer end of handhold shall be not more than eight inches from side of car. (3)One near each side of each end of car on face of end sill or sheathing over end sill, projecting outward or downward. (4)Clearance of outer end of handhold shall be not more than 16 inches from side of car. (5)On each end of cars with platform end sills six or more inches in width, measured from end post or siding, and extending entirely across end of car, there shall be one additional end handhold not less than 24 inches in length, located near centre of car, not less than 30 nor more than 60 inches above platform end sill. Manner of Application 31Horizontal end handholds shall be securely fastened with not less than 1/2-inch bolts with nuts outside (when possible) and riveted over, or with not less than 1/2-inch rivets. Vertical End HandholdsNumber 32Two on full-width platform end sill cars, as heretofore described. Dimensions 33 (1)Minimum diameter, 5/8 inch, wrought iron or steel. (2)Minimum clear length, 18, preferably 24, inches. (3)Minimum clearance, two preferably 2 1/2, inches. Location 34 (1)One on each end of car opposite ladder, not more than eight inches from side of car. (2)Clearance of bottom end of handhold shall be not less than 24 nor more than 30 inches above centre line of coupler. Manner of Application 35Vertical end handholds shall be securely fastened with not less than 1/2-inch bolts with nuts outside (when possible) and riveted over, or with not less than 1/2-inch rivets. Uncoupling LeversNumber 36 (1)Two. (2)Uncoupling levers may be either single or double, and of any efficient design. Dimensions 37 (1)Handles of uncoupling levers, except those shown on Plate B of Schedule II, or of similar designs, shall be not more than six inches from sides of car. (2)Uncoupling levers of design shown on Plate B of Schedule II and of similar designs, shall conform to the following prescribed limits: (a)handles shall be not more than 12, preferably nine, inches from sides of cars; (b)centre lift-arms shall be not less than seven inches long; (c)centre of eye at end of centre lift-arm shall be not more than 3 1/2 inches beyond centre of eye of uncoupling pin of coupler when horn of coupler is against the buffer block or end sill (See Plate B of Schedule II); (d)ends of handles shall extend not less than four inches below bottom of end sill or shall be so constructed as to give a minimum clearance of two inches around handle (See Plate B of Schedule II); (e)minimum drop of handles shall be 12 inches; maximum, 15 inches over all (See Plate B of Schedule II); (f)handles of uncoupling levers of the rocking or push-down type shall be not less than 18 inches from top of rail when lock block has released knuckle, and a suitable stop shall be provided to prevent inside arm from flying up in case of breakage. Location 38 (1)One on each end of car; when single lever is used it shall be placed on left side of end of car. (2)Cars built after June 1, 1919 must be equipped with coupler operating lever connected directly with coupler lock of lock lift without the use of links, clevises or chains. Box or other House Cars Having Centre Sill or Underframe Cushioning Devices with More than Twelve Inches Longitudinal Impact Absorbing TravelHand BrakesNumber 39Same as specified for box and other house cars. Dimensions 40Same as specified for box and other house cars. Location 41Same as specified for box and other house cars. Manner of Application 42Same as specified for box and other house cars. Brake Step 43If brake step is used, it shall not be less than 28 inches in length and the outside edge shall not be less than eight inches from face of car and not less than four inches from a vertical plane parallel with end of car and passing through the inside face of knuckle when closed with coupler horn against buffer block or end sill and the cushioning device at full buff. Manner of Application 44Same as specified for box and other house cars. Running BoardsNumber 45Same as specified for box and other house cars. Dimensions 46Same as specified for box and other house cars. Location 47Same as specified for box and other house cars. Manner of Application 48Running boards shall be continuous from end to end and not cut or hinged at any point; the length and width of running boards may, however, be made up of a number of pieces securely fastened to saddle blocks with screws, bolts, or rivets. The ends of longitudinal running boards shall not be less than six nor more than 10 inches from a vertical plane parallel with end of car and passing through the inside face of knuckle when closed with coupler horn against buffer block or end sill, and the cushioning device at full buff; and if more than four inches from edge of roof of car, shall be securely supported their full width by substantial metal braces. Running boards shall be securely fastened to car and be made of a material which provides the same as or a greater degree of safety than wood of 1 1/8 inch thickness. When made of material other than wood, the tread surface shall be of anti-skid design and constructed with sufficient open space to prevent the accumulation of snow and ice on the tread surface. Sill StepsNumber 49Four. Dimension 50 (1)Minimum cross-sectional area 1/2 inch by 1 1/2 inches, or equivalent, of wrought iron or steel. (2)Minimum length of tread, 10, preferably 12, inches. (3)Minimum clear depth, eight inches. Location 51One near each end on each side of car, so that there shall not be more than 18 inches from end of car to centre of tread of sill step. Outside edge of tread of step shall be not more than four inches inside of face of side of car, preferably flush with side of car. Tread shall be not more than 24, preferably not more than 22, inches above the top of rail. Manner of Application 52Sill steps exceeding 21 inches in depth shall have an additional tread. Sill steps shall be securely fastened with not less than 1/2-inch bolts with nuts outside (when possible) and riveted over or with not less than 1/2-inch rivets. LaddersNumber 53Same as specified for box and other house cars. Dimensions 54 (1)Minimum clear length of tread (a)side ladders 16 inches; (b)end ladders 14 inches. (2)Maximum spacing between ladder treads, 19 inches. (3)Top ladder tread shall be located not less than 12 nor more than 18 inches from roof at eaves. (4)Spacing of side ladder treads shall be uniform within a limit of two inches from top ladder tread to bottom tread of ladder. (5)Maximum distance from bottom tread of side ladder to top tread of sill step, 21 inches. (6)End ladder treads shall, where construction of car permits, be spaced to coincide with treads of side ladders, a variation of two inches being allowed; where construction of car will not permit the application of a tread of end ladder to coincide with bottom tread of side ladder, the bottom tread of end ladder shall coincide with second tread from bottom of side ladder. (7)One tread of end ladders shall be located below the bottom of the end sill. (8)Iron or steel treads, minimum diameter 5/8 inch. (9)Minimum clearance of treads, two, preferably 2 1/2, inches. Location 55Same as specified for box and other house cars. Manner of Application 56Same as specified for box and other house cars. End Ladder Clearance 57No part of car above end sills within 30 inches from side of car, except buffer block, brake shaft, brake wheel, brake step, running board, end platform, or uncoupling lever shall extend to within 12 inches of vertical plane parallel with end of car and passing through the inside face of knuckle, when closed with the coupler horn against the buffer block or end sill, and the cushioning device at full buff, and no other part of end of car or fixtures on same above end sill, other than exceptions herein noted, shall extend beyond the outer face of buffer block. Roof HandholdsNumber 58Same as specified for box and other house cars. Dimensions 59Same as specified for box and other house cars. Location 60Same as specified for box and other house cars. Manner of Application 61Same as specified for box and other house cars. Side HandholdsNumber 62Sixteen. (Treads of side ladders are side handholds.) Dimensions 63Same as specified for box and other house cars. Location 64Horizontal (1)Four near right end on each side of car. (2)Four near left end on each side of car, all side handholds shall be spaced not more than 19 inches apart and with the bottom handhold located not more than 21 inches from top tread of sill step. Such handholds shall meet ladder specifications and clearance of outer ends of handholds shall be not more than eight inches from end of car. Manner of Application 65Bottom side handholds shall have footguards or upward projections not less than two inches in height near inside ends. Side handholds shall be securely fastened with not less than 1/2-inch bolts with nuts outside (when possible) and riveted over, or with not less than 1/2-inch rivets. Horizontal End HandholdsNumber 66Eighteen or more (Nine on each end of car.) (Treads of end ladders are end handholds.) Dimensions 67Same as specified for box and other house cars. Location 68 (1)One near each side of each end of car on face of end sill or sheathing over end sill, projecting outward or downward. (2)Three near each side of each end of car directly over the end sill handhold spaced not more than 19 inches apart to coincide with side handholds, with a variation of not more than two inches being allowed; except as provided above when tread of end ladder is an end handhold. Clearance of outer end of handholds shall be not more than eight inches from side of car. (3)One not less than 36 inches in length located on each end near centre of car not less than 30 nor more than 60 inches above end platform. Manner of Application 69The end sill handholds near the right side of car shall have footguards or upward projections not less than two inches in height near inside end. End handholds shall be securely fastened with not less than 1/2-inch bolts with nuts outside and riveted over or with not less than 1/2-inch rivets. End PlatformsNumber 70Two. Dimensions 71Not less than eight inches wide and of such length as to substantially fill the space between the end ladders and the end handholds, but not less than 60 inches. Location 72One near the centre on each end of car not more than eight inches above centre sill. Manner of Application 73End platforms shall be supported by not less than three metal braces having a minimum cross-sectional area 3/8 inch by 1 1/2 inches or equivalent which shall be securely fastened to body of car with not less than 1/2-inch bolts or rivets. The outer edges of end platforms shall not extend to a point less than six inches from a vertical plane parallel with end of car and passing through the inside face of knuckle when closed with coupler horn against the buffer block or end sill and the cushioning device at full buff. End platforms shall be made of suitable running board material. Uncoupling LeversNumber 74Same as specified for box and other house cars. Dimensions 75Same as specified for box and other house cars. Location 76Same as specified for box and other house cars. Uncoupling Device and Brake Pipe Appurtenances 77When a part of the uncoupling device and/or brake pipe is located parallel to the exposed ends of the centre sill, such part shall be installed in a manner providing at least two inches of clearance near the coupler of sufficient length to permit use as a handhold. Exposed Top Sections of Centre Sills 78The top of the exposed end of centre sill shall be coated with anti-skid paint. Box or other House Cars Having Centre Sill or Underframe Cushioning Devices with Twelve Inches or Less Longitudinal Impact Absorbing TravelHand BrakesNumber 79Same as specified for box and other house cars. Dimensions 80Same as specified for box and other house cars. Location 81Same as specified for box and other house cars. Manner of Application 82Same as specified for box and other house cars. Brake Step 83If brake step is used, it shall not be less than 28 inches in length. Outside edge shall be not less than eight inches from face of car and not less four inches from a vertical plane parallel with end of car and passing through the inside face of knuckle when closed with coupler horn against buffer block or end sill and the cushioning device at full buff. Manner of Application 84Same as specified for box and other house cars. Running BoardsNumber 85Same as specified for box and other house cars. Dimensions 86Same as specified for box and other house cars. Location 87Same as specified for box and other house cars. Manner of Application 88Running boards shall be continuous from end to end and not cut or hinged at any point; the length and width of running boards may, however, be made up of a number of pieces securely fastened to saddle blocks with screws, bolts, or rivets. The ends of longitudinal running board shall not be less than six nor more than 10 inches from a vertical plane parallel with end of car and passing through the inside face of knuckle when closed with coupler horn against buffer block or end sill, and the cushioning device at full buff; and if more than four inches from edge of roof of car, shall be securely supported their full width by substantial metal braces. Running board shall be securely fastened to car and be made of a material which provides the same as or a greater degree of safety than wood of 1 1/8-inch thickness. When made of material other than wood, the tread surface shall be of anti-skid design and constructed with sufficient open space to prevent the accumulation of snow and ice on the tread surface. Sill StepsNumber 89Four. Dimensions 90 (1)Minimum cross-sectional area 1/2 inch by 1 1/2 inches, or equivalent, of wrought iron or steel. (2)Minimum length of tread, 10, preferably 12, inches. (3)Minimum clear depth, eight inches. Location 91One near each end each side of car, so that there shall be not more than 18 inches from end of car to centre of tread of sill step. Outside edge of tread of step shall be not more than four inches inside of face of side of car, preferably flush with side of car. Tread shall be not more than 24, preferably not more than 22, inches above the top of rail. Manner of Application 92Sill steps exceeding 21 inches in depth shall have an additional tread. Sill steps shall be securely fastened with not less than 1/2-inch bolts with nuts outside (when possible) and riveted over, or with not less than 1/2-inch rivets. LaddersNumber 93Same as specified for box and other house cars. Dimensions 94 (1)Minimum clear length of tread (a)side ladders, 16 inches; (b)end ladders, 14 inches. (2)Maximum spacing between ladder treads, 19 inches. (3)Top ladder tread shall be located not less than 12 nor more than 18 inches from roof at eaves. (4)Spacing of side ladder treads shall be uniform within a limit of two inches from top ladder tread to bottom tread of ladder. (5)Maximum distance from bottom tread of side ladder to top tread of sill step, 21 inches. (6)End ladder treads shall, where construction of car permits, be spaced to coincide with treads of side ladders, a variation of two inches being allowed; where construction of car will not permit the application of a tread of end ladder to coincide with bottom tread of side ladder, the bottom tread of end ladder shall coincide with second tread from bottom of side ladder. (7)One tread of end ladders shall be located below the bottom of the end sill. (8)Iron or steel treads, minimum diameter 5/8 inch. (9)Minimum clearance of treads, two, preferably 2 1/2, inches. Location 95Same as specified for box and other house cars. Manner of Application 96Same as specified for box and other house cars. End Ladder Clearance 97No part of car above end sills within 30 inches from side of car, except buffer block, brake shaft, brake wheel, brake step, running board, or uncoupling lever shall extend to within 12 inches of vertical plane parallel with end of car and passing through the inside face of knuckle, when closed with the coupler horn against the buffer block or end sill, and the cushioning device at full buff, and no other part of end of car or fixtures on same above end sill, other than exceptions herein noted, shall extend beyond the outer face of buffer block. Roof HandholdsNumber 98Same as specified for box and other house cars. Dimensions 99Same as specified for box and other house cars. Location 100Same as specified for box and other house cars. Manner of Application 101Same as specified for box and other house cars. Side HandholdsNumber 102Same as specified for box and other house cars. (Tread of side ladder is a side handhold.) Dimensions 103Same as specified for box and other house cars. Location 104Same as specified for box and other house cars. Manner of Application 105Same as specified for box and other house cars. Horizontal End HandholdsNumber 106Same as specified for box and other house cars. (Tread of end ladder is an end handhold.) Dimensions 107Same as specified for box and other house cars. Location 108Same as specified for box and other house cars. Manner of Application 109Same as specified for box and other house cars. Uncoupling LeversNumber 110Same as specified for box and other house cars. Dimensions 111Same as specified for box and other house cars. Location 112Same as specified for box and other house cars. Box and other House Cars Built New or Rebuilt After October 1, 1966, or Under Construction Prior Thereto, Except Cars Equipped with Roof HatchesHand BrakesNumber 112.1 (1)Each car shall be equipped with an efficient vertical wheel hand brake which shall operate in harmony with the power brake thereon. (2)The hand brake may be of any efficient design, but must provide a total braking force applied to brake shoes not less than the total force applied to the brake shoes by the brake cylinders at 50 pounds per square inch. Dimensions 112.2 (1)The brake wheel may be deep or shallow, of malleable iron, wrought iron, steel, or other material of equivalent strength. (2)Overall diameter of brake wheel nominally 22 inches. (3)Depth of brake wheel hub shall be 2 5/8 inches with square taper shaft fit, taper two inches in 12 inches with small end of taper fit 7/8 inch. (4)Brake wheel and drum shall be arranged so that both will revolve when applying and gradually releasing the hand brake. Hand brake shall be provided with means to prevent application of the brake by winding in a counterclockwise direction. (5)All chains shall be not less than 9/16 inch BBB coil chain. (6)All hand brake rods shall be not less than 3/4 inch diameter. Location 112.3 (1)The hand brake shall be so located that it can be safely operated from horizontal end platform while car is in motion. (2)The brake shaft shall be located on end of car, to the left of and not less than 17 nor more than 22 inches from centre and not less than 26 nor more than 40 inches above top of end platform tread. NOTE:Cars with roofs 16 feet 10 inches or more above top of rail, brake shaft to be located to left of centre and not more than 24 inches from left side of car. Manner of Application 112.4 (1)There shall be not less than four inches clearance around rim of brake wheel. (2)Brake wheel shall be held in position on brake shaft by a nut on a threaded extended end of brake shaft, said threaded portion shall be not less than  3/4 inch in diameter; said nut shall be secured by riveting over or by the use of a lock-nut or suitable cotter. (3)Outside edge of brake wheel shall be not less than four inches from a vertical plane parallel with end of car and passing through the inside face of knuckle when closed with coupler horn against the buffer block or end sill. (4)Hand brake housing shall be securely fastened to car. (5)Brake shaft shall be arranged with a square fit at its outer end to secure the hand brake wheel; said square fit shall be not less than 7/8 inch square. Square fit taper; nominally 2 in 12 inches (See Plate A in Schedule II). Sill StepsNumber 112.5Four. Dimensions 112.6Minimum cross-sectional area 1/2 inch by 1 1/2  inches, or equivalent, of wrought iron, steel, or other material of equivalent strength. Minimum length of tread, 10, preferably 12, inches. Minimum clear depth, eight inches. Location 112.7 (1)One near each end of each side of car, so that there shall be no more than 18 inches from end of car to centre of tread of sill step. (2)Outside edge of tread of step shall be not more than four inches inside of face of side of car, preferably flush with side of car. (3)Tread shall be not more than 24, preferably not more than 22, inches above the top of rail. Manner of Application 112.8 (1)Sill steps exceeding 21 inches in depth shall have an additional tread. (2)Sill steps shall be securely fastened with not less than 1/2-inch bolts with nuts outside (when possible) and riveted over, or with not less than 1/2-inch rivets. End Appliances Clearance 112.9No part of car above end sills within 30 inches from side of car, except buffer block, brake shaft, brake wheel, end platform, horizontal end handholds or uncoupling lever shall extend to within 12 inches of a vertical plane parallel with end of car and passing through the inside face of knuckle, when closed with the coupler horn against the buffer block or end sill and cushioning device (if used) at full buff, and no other part of end of car or fixtures on same above end sills, other than exceptions herein noted shall extend beyond outer face of buffer block. Side HandholdsNumber 112.10Sixteen. 112.11Minimum diameter, 5/8 inch, wrought iron, steel, or other material of equivalent strength. Minimum clear length 16 inches, preferably 24 inches. Minimum clearance, two, preferably 2 1/2 inches. Location 112.12Horizontal: (1)Four near each end and on each side of car spaced not more than 19 inches apart and with the bottom handhold located not more than 21 inches from top tread of sill step, and top handhold shall coincide in height with top end handhold, a variation of two inches being allowed. Spacing of side handholds shall be uniform within a limit of two inches from top handhold to bottom handhold. (2)Clearance of outer ends of handholds shall be not more than eight inches from end of car. Manner of Application 112.13Side handholds shall be securely fastened with not less than  1/2-inch bolts with nuts outside (when possible) and riveted over, or with not less than 1/2-inch rivets. Each bottom handhold shall have foot guard or upward projection not less than two inches in height near inside end. End HandholdsNumber 112.14Sixteen. Dimensions 112.15 (1)Minimum diameter, 5/8 inch, wrought iron, steel, or other material of equivalent strength. (2)Minimum clear length, 16 inches, preferably 24 inches. (3)Minimum clearance, two inches, preferably 2 i/2, inches. Location 112.16Horizontal: Four near each side and on each end of car spaced not more than 19 inches apart and with the bottom handhold located not more than 21 inches from top tread of sill step, and top handhold shall coincide in height with end platform handholds, a variation of two inches being allowed. Clearance of outer ends of handholds shall be not more than eight inches from side of car. Manner of Application 112.17End handholds shall be securely fastened with not less than 1/2-inch bolts with nuts outside (when possible) and riveted over, or with not less than 1/2-inch rivets. Each bottom handhold shall have foot guard or upward projection not less than two inches in height near inside end. NOTE:Not required on cars with roofs 16 feet 10 inches or more above top of rail when vertical and horizontal end handholds as specified in note following section 112.25 of this Schedule are applied. End PlatformsNumber 112.18Two. Dimensions 112.19Width not less than eight inches, length not less that 60 inches. Location 112.20One centered on each end of car not more than eight inches above top of centre sill. Manner of Application 112.21 (1)Each end platform shall be securely supported by not less than three metal braces having a minimum cross sectional area of 3/8 inch by 1 1/2 inches or equivalent, which shall be securely fastened to body of car with not less than 1/2-inch bolts or rivets. NOTE:Cars with roofs 16 feet 10 inches or more above top of rail will have end platforms not less than 10 inches in width, length, full width of car and supported by not less than four metal braces. (2)Where conventional draft gear or cushioning device having longitudinal travel less than six inches is used the outside edge of each end platform shall be not less than 12 inches from a vertical plane parallel with end of car and passing through the inside face of knuckle when closed with coupler horn against buffer block. Where cushioning device having longitudinal travel six inches or more is used, the outside edge of each end platform shall be not less than six inches from a vertical plane parallel with end of car and passing through the inside face of knuckle when closed with end sill and cushioning device at full buff. End platform shall be made of wood or material that provides the same or a greater degree of safety than wood, of 1 1/8-inch thickness. When made of material other than wood, the tread surface shall be of anti-skid design and constructed with sufficient open space to permit the elimination of snow and ice from the tread surface. Horizontal End Platform HandholdsNumber 112.22Two. Dimensions 112.23 (1)Minimum diameter, 5/8 inch, wrought iron, steel, or other material of equivalent strength. (2)Minimum clearance, two, preferably 2 1/2 inches. (3)Minimum clear length 60 inches. When security of attachment requires, an extra supporting leg may be applied near centre of clear length. Location 112.24One on each end of car above end platform. Outer legs shall be not more than six inches from inner legs of top end handholds. Height above tread of end platform: not less than 48 nor more than 60 inches. Manner of Application 112.25End platform handholds shall be securely fastened with not less than 1/2-inch bolts with nuts outside (when possible) and riveted over, or with not less than 1/2-inch rivets. NOTE:Cars with roofs 16 feet 10 inches or more above top of rail will have horizontal end platform handholds extending across each end of car with clearance at each end of not more than four inches from side of car supported by an extra leg near centre of handholds, and with vertical and horizontal end handholds as follows: Vertical End HandholdsNumberFour. DimensionsMinimum diameter 5/8 inch, wrought iron, steel, or other material of equivalent strength. Minimum clearance two, preferably 2 1/2, inches. LocationOne on each side of each end of car, not more than four inches from side of car, extending downward from end of horizontal end platform handhold to within eight inches above tread of end platform. One continuous handhold with two right angle handholds, may take the place of two specified vertical end handholds and one horizontal end platform handhold, provided the dimensions and location coincide, and extra legs at points of angle and centre are provided and securely fastened to car. Horizontal End HandholdsNumberFour. Dimensions (1)Minimum diameter 5/8 inch, wrought iron, steel, or other material of equivalent strength. (2)Minimum clear length, 16 inches, preferably 24 inches. (3)Notwithstanding subsection 2, a handhold 14 inches in length may be used where it is impossible to use one 16 inches in length. (4)Minimum clearance two, preferably 2 1/2, inches. LocationOne near each side of each end of car on outer edge of end platform projecting downward with clearance of outer end not more than 16 inches from side of car. Manner of ApplicationHorizontal end handholds shall be securely fastened with not less than 1/2-inch bolts with nuts outside (when possible) and riveted over, or with not less than 1/2-inch rivets. Uncoupling LeversNumber 112.26Two. Dimensions 112.27 (1)Handles of uncoupling levers except those shown on Plate B of Schedule II or of similar design, shall be not more than six inches from sides of car. (2)Uncoupling levers of design shown on Plate B of Schedule II and of similar designs shall conform to the following prescribed limits: (a)handles shall be not more than 12, preferably nine, inches from sides of cars; (b)centre lift arms shall be not less than seven inches long; (c)centre of eye at end of centre lift arm shall be not more than  3 1/2 inches beyond centre of eye of uncoupling pin of coupler when horn of coupler is against the buffer block or end sill (See Plate B of Schedule II); (d)ends of handles shall extend not less than four inches below bottom of end sill or shall be so constructed as to give a minimum clearance of two inches around handle (See Plate B of Schedule II); (e)minimum drop of handles shall be 12 inches, maximum, 15 inches overall (See Plate B of Schedule II); (f)handles of uncoupling levers of the rocking or push down type shall be not less than 18 inches from top of rail when lock block has released knuckle, and a suitable stop shall be provided to prevent inside arm from flying up in case of breakage. Location 112.28One on each end of car. When single lever is used, it shall be placed on left side of end of car. Painting and Stencilling 112.29 (1)This section applies to cars with roofs 16 feet 10 inches or more above top of rail only. (2)That portion of each end of car more than 15 feet above top of rail shall be painted with contrasting reflectorized paint and shall bear the words “NO RUNNING BOARD” to the left of centre and “EXCESS HEIGHT CAR” to the right of centre. Lettering to be not less than three inches high. On each side sill near end corner there shall be painted a yellow rectangular area with a 3/4-inch black border containing the words “THIS CAR EXCESS HEIGHT — NO RUNNING BOARD”. Lettering to be not less than 1 1/2 inches high. When a car is equipped with centre sill or underframe cushioning device having more than 12 inches longitudinal impact absorbing travel, and a part of the uncoupling device and/or brake pipe is located parallel to the exposed end of the centre sill, such part shall provide at least two inches of clearance near the coupler of sufficient length to permit use as a handhold during air hose coupling operation and the top of exposed ends of sliding centre sill shall be coated with anti-skid paint. Existing Box and other House Cars Without Roof Hatches 112.30Box and other house cars built on or before October 1, 1966 or under construction prior thereto shall be deemed equipped as nearly as possible within the intent of these requirements when (a)the running board, roof handholds over side and end ladders at “A” end of car and ladder treads above the fourth tread from bottom of side and end ladder at “A” end are removed; and (b)one horizontal end platform handhold is applied on each end of car as specified in this section except the right hand end shall be not more than eight inches from side of car, or where car end contour makes impractical the use of a single continuous end handhold, there is applied the equivalent consisting of two handholds, the centre handhold to be a minimum of 30 inches in clear length and the handhold to the right to be a minimum of 19 inches in clear length and to extend to within eight inches of the right side of the car, such handholds to be not more than 12 inches apart; and (c)with hand brake operated near roof of car: a brake step shall be provided as specified in section 5 of this Schedule and lettering 1 1/2 inches high shall be painted on a yellow background on side sill near “B” end of car with a 3/4-inch black border containing the words “KEEP OFF ROOF — NO RUNNING BOARD”, or with hand brake operated from approximate level of top of end sill: roof handholds and side and end ladder treads above the fourth tread from the bottom of ladders at “B” end of car shall be removed and a brake step as specified by section 5 of this Schedule shall be used with top of tread surface being level with or not more than four inches below adjacent end handhold. Paragraph (b) shall not apply to cars equipped with end platforms and end platform handholds. Box and Other House Cars with Roof Hatches(Same as Specified for Box and other House Cars Without Roof Hatches Except for the Provisions of Sections 112.31 to 112.43 of this Schedule)Running Boards 112.31Same as specified in sections 7 to 10 of this Schedule except: the end of longitudinal running board shall be not less than six inches from a vertical plane parallel with end of car and passing through the inside face of knuckle when closed with coupler horn against buffer block or end sill. LaddersNumber 112.32Two. Dimensions 112.33Minimum clear length of tread 16 inches; maximum spacing between treads 19 inches. Location 112.34One on each end of car not more than eight inches from left hand side. Manner of Application 112.35Same as specified in section 18 of this Schedule. Roof HandholdsNumber 112.36Two, one  over each ladder. Dimensions 112.37Same as specified in section 21 of this Schedule. Location 112.38Same as specified in section 22 of this Schedule. Manner of Application 112.39Same as specified in section 23 of this Schedule. End Handholds(Treads of end ladders are end handholds)Number 112.40Sixteen. Dimensions 112.41 (1)Minimum diameter, 5/8 inch, wrought iron, steel, or other material of equivalent strength. (2)Minimum clear length, 16 inches, preferably, 24 inches. (3)Minimum clearance, two, preferably 21/2, inches. Location 112.42Horizontal: Four near each side and on each end of car spaced not more than 19 inches apart and with the bottom handhold located not more than  21 inches from top tread of sill step, and top handhold shall coincide in height with end platform handholds, a variation of two inches being allowed. Clearance of outer ends of handholds shall be not more than eight inches from side of car. Manner of Application 112.43End handholds shall be securely fastened with not less than  1/2-inch bolts with nuts outside (when possible) and riveted over, or with not less than 1/2-inch rivets. Each bottom handhold shall have foot guard or upward projection not less than two inches in height near inside end. Existing Box and other House Cars with Roof Hatches 112.44Box and other house cars with roof hatches built on or before October 1, 1966, or under construction prior thereto, shall be deemed equipped as nearly as possible within the intent of these requirements when equipped with the same complement of safety appliances, depending upon type, as is specified in sections 112.31 to 112.43, for box and other house cars with roof hatches except (a)the side ladder treads above the fourth tread from bottom of side ladder near “A” end of car and roof handhold over the side ladder near “A” end shall be removed; (b)one end platform handhold shall be provided on each end of car as specified in paragraph 112.30 (b) of this Schedule and when hand brake is operated near roof of car a brake step shall be provided as specified by paragraph 112.30(c) of this Schedule or when hand brake is operated from approximate level of top of end sill the roof handhold over side ladder near “B” end and treads above the fourth tread from bottom of side ladder near “B” end shall be removed and a brake step as specified in paragraph 112.30(c) of this Schedule shall be used with top of tread surface level with or not more than four inches below adjacent end handhold. Hopper Cars and High-Side Gondolas with Fixed Ends(Cars with Sides more than 36 Inches above the Floor are High-side Cars)Hand BrakesNumber 113Same as specified in section 1 of this Schedule. Dimensions 114Same as specified in section 2 of this Schedule. Location 115 (1)Each hand brake shall be so located that it can be safely operated while car is in motion. (2)The brake shaft shall be located on end of car to the left of, and not more than 22 inches from centre. Manner of Application 116Same as specified in section 4 of this Schedule. Brake Step 117Same as specified in sections 5 and 6 of this Schedule. 1Sill Steps 118Same as in sections 11, 12, 13 and 14 of this Schedule. LaddersNumber 119Same as specified in section 15 of this Schedule. Dimensions 120Same as specified in section 16, except that top ladder tread shall be located not more than four inches from top of car. Location 121Same as specified in section 17 of this Schedule. Manner of Application 122Same as specified in section 18 of this Schedule. Side Handholds 123Same as specified in sections 24, 25, 26 and 27 of this Schedule. Horizontal End Handholds 124Same as specified in sections 28, 29, 30 and 31 of this Schedule. Vertical End Handholds 125Same as specified in sections 32, 33, 34 and 35 of this Schedule. Uncoupling Levers 126Same as specified in sections 36, 37 and 38 of this Schedule. End Ladder Clearance 127No part of car above end sills within 30 inches from side of car except buffer block, brake shaft, brake wheel, brake step or uncoupling lever shall extend to within 12 inches of a vertical plane parallel with end of car and passing through the inside face of knuckle when closed with coupler horn against the buffer block or end sill, and no other part of end of car or fixtures on same above end sills, other than exceptions herein noted, shall extend beyond the outer face of buffer block. Drop-end High-side Gondola CarsHand BrakesNumber 128Same as specified in section 1 of this Schedule. Dimensions 129Same as specified in section 2 of this Schedule. Location 130 (1)Each hand brake shall be so located that it can be safely operated while car is in motion. (2)The brake shaft shall be located on end of car to the left of centre. Manner of Application 131Same as specified in section 4 of this Schedule. 1Sill Steps 132Same as specified in sections 11, 12, 13 and 14 of this Schedule. LaddersNumber 133Two. Dimensions 134Same as specified in section 16 of this Schedule, except that top ladder tread shall be located not more than four inches from top of car. Location 135One on each side, not more than eight inches from right end of car, measured from inside edge of ladder-stile or clearance of ladder treads to corner of car. Manner of Application 136Same as specified in section 18 of this Schedule. Side Handholds 137Same as specified in sections 24, 25, 26 and 27 of this Schedule. Horizontal End HandholdsNumber 138Four. Dimensions 139Same as specified in section 29 of this Schedule. Location 140 (1)One near each side of each end of car on face of end sill. (2)Clearance of outer end of handhold shall be not more than 16 inches from side of car. Manner of Application 141Same as specified in section 31 of this Schedule. Uncoupling Levers 142Same as specified in sections 36, 37 and 38 of this Schedule. End Ladder Clearance 143No part of car above end sills within 30 inches from side of car, except buffer block, brake shaft, brake wheel or uncoupling lever shall extend to within 12 inches of a vertical plane parallel with end of car and passing through the inside face of knuckle when closed with coupler horn against the buffer block, or end sill, and no other part of end of car or fixtures on same above end sills, other than exceptions herein noted, shall extend beyond the outer face of buffer block. Fixed-End, Low-Side Gondola and Low-Side Hopper Cars(Cars with Sides 36 Inches or less above the Floor Are Low-side Cars)Hand BrakesNumber 144Same as specified in section 1 of this Schedule. Dimensions 145Same as specified in section 2 of this Schedule. Location 146 (1)Each hand brake shall be so located that it can be safely operated while car is in motion. (2)The brake shaft shall be located on end of car, to the left of and not more than 22 inches from centre. Manner of Application 147Same as specified in section 4 of this Schedule. Brake Step 148Same as specified in sections 5 and 6 of this Schedule. 1Sill Steps 149Same as specified in sections 11, 12, 13 and 14 of this Schedule. Side HandholsNumber 150Same as specified in section 24 of this Schedule. Dimensions 151Same as specified in section 25 of this Schedule. Location 152 (1)Horizontal: one near each end on each side of car, not less than 24 nor more than 30 inches above centre line of coupler if car construction will permit but handhold shall not project above top of side. (2)Clearance of outer end of handhold shall be not more than eight inches from end of car. Manner of Application 153Same as specified in section 27 of this Schedule. Horizontal End HandholdsNumber 154Same as specified in section 28 of this Schedule. Dimensions 155Same as specified in section 29 of this Schedule. Location 156 (1)One near each side on each end of car not less than 24 nor more than 30 inches above centre line of coupler, if car construction will permit. Clearance of outer end of handhold shall be not more than eight inches from side of car. (2)One near each side of each end of car on face of end sill, projecting outward or downward. Clearance of outer end of handhold shall be not more than 16 inches from side of car. Manner of Application 157Same as specified in section 31 of this Schedule. Uncoupling Levers 158Same as specified in sections 36, 37 and 38 of this Schedule. End Ladder Clearance 159No part of car above end sills within 30 inches from side of car, except buffer block, brake shaft, brake step, brake wheel, or uncoupling lever shall extend to within 12 inches of a vertical plane parallel with end of car and passing through the inside face of knuckle when closed with coupler horn against the buffer block or end sill, and no other part of end of car or fixtures on same above end sills, other than exceptions herein noted, shall extend beyond the outer face of buffer block. Drop-end Low-side Gondola CarsHand BrakesNumber 160Same as specified in section 1 of this Schedule. Dimensions 161Same as specified in section 2 of this Schedule. Location 162 (1)Each hand brake shall be so located that it can be safely operated while car is in motion. (2)The brake shaft shall be located on end of car to the left of centre. Manner of Application 163Same as specified in section 4 of this Schedule, except that top brake shaft support may be omitted. 1Sill Steps 164Same as specified in sections 11, 12, 13 and 14 of this Schedule. Side HandholdsNumber 165Same as specified in section 24 of this Schedule. Dimensions 166Same as specified in section 25 of this Schedule. Location 167 (1)Horizontal: one near each end on each side of car, not less than  24 nor more than 30 inches above centre line of coupler, if car construction will permit, but handhold shall not project above top of side. (2)Clearance of outer end of handhold shall be not more than eight inches from end of car. Manner of Application 168Same as specified in section 27 of this Schedule. End HandholdsNumber 169Four. Dimensions 170Same as specified in section 29 of this Schedule. Location 171Horizontal: one near each side of each end of car on face of end sill. Clearance of outer end of handhold shall be not more than 16 inches from side of car. Manner of Application 172Same as specified in section 31 of this Schedule. Uncoupling Levers 173Same as specified in sections 36, 37 and 38 of this Schedule. End Ladder Clearance 174No part of car above end sills within 30 inches from side of car, except buffer block, brake shaft, brake wheel or uncoupling lever shall extend to within 12 inches of a vertical plane parallel with end of car and passing through the inside face of knuckle when closed with coupler horn against the buffer block or end sill, and no other part of end of car or fixtures on same above end sills, other than exceptions herein noted, shall extend beyond the outer face of buffer block. Flat Cars(Cars with Sides 12 Inches or less above the Floor may be Equipped the same as Flat Cars)Hand BrakesNumber 175Same as specified in section 1 of this Schedule. Dimensions 176Same as specified in section 2 of this Schedule. Location 177 (1)Each hand brake shall be so located that it can be safely operated while car is in motion. (2)The brake shaft shall be located on the end of car to the left of centre, or on side of car not more than 36 inches from right-hand end thereof. Manner of Application 178Same as specified in section 4 of this Schedule. 1Sill Steps 179Same as specified in sections 11, 12, 13 and 14 of this Schedule. Side HandholdsNumber 180Same as specified in section 24 of this Schedule. Dimensions 181Same as specified in section 25 of this Schedule. Location 182 (1)Horizontal: one on face of each side sill near each end. (2)Clearance of outer end of handhold shall be not more than 12 inches from end of car. Manner of Application 183Same as specified in section 27 of this Schedule. End HandholdsNumber 184Four. Dimensions 185Same as specified in section 29 of this Schedule. Location 186 (1)Horizontal: one near each side of each end of car on face of end sill. (2)Clearance of outer end of handhold shall be not

    The text continues in the official source.

    Related guides, FAQ and contract templates