Beta
7 CFR § 42.112
7 CFR § 42.112 — § 42.112 Defects of containers: Tables IV, V, VI, VII, VIII, IX, and X.
Beta. Legal information, not legal advice. LEGALDIGM is not a law firm. Check the official source for the current text.
Analyze this law with AI§ 42.112 Defects of containers: Tables IV, V, VI, VII, VIII, IX, and X.
Table IV—Metal Containers [Rigid and semi-rigid]
Defects
Categories
Critical
Major
Minor
Type or size of container or component parts not as specified
None permitted
Closure incomplete, not located correctly or not sealed, crimped, or fitted properly:
(a) Heat processed primary container
1
(b) Non-heat processed primary container
101
(c) Other than primary container
201
Dirty, stained, or smeared container
202
Key opening metal containers (when required):
(a) Key missing
102
(b) Key does not fit tab
103
(c) Tab of opening band insufficient to provide accessibility to key
104
(d) Improper scoring (band would not be removed in one continuous strip)
105
Metal pop-top:
(a) Missing or broken pull tab
106
(b) Missing or incomplete score line (not conforming to a relevant product specification)
107
Flexible pop-top:
(a) Poor seal (wrinkle, entrapped matter, etc.)
108
(b) Short pull tab (not conforming to a relevant product specification)
203
(c) Missing pull tab
109
(d) Torn pull tab
204
Open top with plastic overcap (when required):
(a) Plastic overcap missing
110
(b) Plastic overcap warped (making opening or reapplication difficult)
111
Outside tinplate or coating (when required):
(a) Missing or incomplete
205
(b) Blistered, flaked, sagged, or wrinkled
206
(c) Scratched or scored
207
(d) Fine cracks
208
Rust (rust stain confined to the top or bottom double seam or rust that can be removed with a soft cloth is not scored a defect):
(a) Rust stain
209
(b) Pitted rust
112
Wet cans (excluding refrigerated containers)
210
Dent:
(a) Materially affecting appearance but not usability
211
(b) Materially affecting usability
113
Buckle:
(a) Not involving end seam
212
(b) Extending into the end seam
114
Collapsed container
115
Paneled side materially affecting appearance but not usability
213
Solder missing when required
116
Cable cut exposing seam
117
Improper side seam
118
Swell, springer, or flipper (not applicable to gas or pressure packed product nor frozen products)
2
Leaker or blown container
3
Frozen products only:
(a) Bulging ends 3 ⁄ 16 -inch to 1 ⁄ 4 -inch beyond lip
214
(b) Bulging ends more than 1 ⁄ 4 -inch beyond lip
119
Metal drums: leaking filling seal (bung) swell 1
4
120
1 Defect classification depends on the severity of the defect.
Table V—Composite Containers [Fiberboard body with metal lids or metal bottoms, plastic or foil top with cap]
Defects
Categories
Critical
Major
Minor
Type or size of container or component parts not as specified
None permitted
Closure incomplete, not located correctly or not sealed, crimped, or fitted properly
1
Dirty, stained, or smeared container
201
Easy open closure:
(a) Pull tab:
1. Missing or broken pull tab
101
2. Missing or incomplete score line
102
(b) Membrane top:
1. Poor seal (wrinkle, entrapped matter, etc.)
103
2. Short pull tab
104
3. Missing pull tab
105
4. Torn pull tab
106
(c) Open top with plastic overcap (when required):
1. Plastic overcap missing
107
2. Plastic overcap warped (making opening or reapplication difficult)
108
Outside tinplate or coating on ends (when required):
(a) Missing or incomplete
202
(b) Blistered, flaked, sagged, or wrinkled
203
(c) Scratched or scored
204
(d) Fine cracks
205
Collapsed container
109
Paneled side materially affecting appearance but not usability
206
Leaker
2
Wet or damp:
(a) Materially affecting appearance but not usability
207
(b) Materially affecting usability
110
Crushed or torn area:
(a) Materially affecting appearance but not usability
208
(b) Materially affecting usability
111
Table VI—Glass Containers [Bottles, Jars]
Defects
Categories
Critical
Major
Minor
Type or size of container or component parts not as specified
None permitted
Closure not sealed, crimped, or fitted properly:
(a) Heat processed
1
(b) Non-heat processed
101
Dirty, stained, or smeared container
201
Chip in glass
202
Stone (unmelted material) in glass
203
Pits in surface of glass
204
Sagging surface
205
Bead (bubble within glass):
(a) 1 ⁄ 8 -inch to 1 ⁄ 16 -inch in diameter
206
(b) Exceeding 1 ⁄ 8 -inch in diameter
102
Checked
103
Thin spot in glass
104
Blister (structural defect)
105
Bird swing (glass appendage inside container)
2
Broken or leaking container
3
Cap (nonheat processed):
(a) Cross-threaded
207
(b) Loose but not leaking
208
(c) Pitted rust
106
Cap (heat processed):
(a) Cross-threaded or loose
4
(b) Pitted rust
107
Sealing tape or cello band (when required):
(a) Improperly placed
209
(b) Not covering juncture of cap and glass
108
(c) Ends overlap by less than 1 ⁄ 2 -inch
109
(d) Loose or deteriorating
110
Missing or torn outer safety seal
111
Inner safety seal—missing, torn, poor seal
112
Table VII—Plastic Containers [Rigid and Semi-Rigid, Bottles, Jars, Tubs, Trays, Pails, etc.]
Defects
Categories
Critical
Major
Minor
Type or size of container or component parts not as specified
None permitted
Closure not sealed, crimped, or fitted properly:
(a) Heat processed
1
(b) Non-heat processed
101
Dirty, stained, or smeared container
201
Chip in plastic
202
Un-melted gels in plastic
203
Pits in surface of plastic
204
Sagging surface
205
Air bubble within plastic:
(a) 1 ⁄ 8 -inch to 1 ⁄ 16 -inch in diameter
206
(b) Exceeding 1 ⁄ 8 -inch in diameter
102
Checked
103
Thin spot in plastic
104
Blister (structural defect)
105
Broken or leaking container
2
Cap (non-heat processed):
(a) Cross-threaded
207
(b) Loose but not leaking
208
Cap (heat processed), cross-threaded or loose
3
Security seals:
(a) Closure ring missing
106
(b) Missing or torn outer safety seal
107
(c) Inner safety seal—missing, torn, or poor seal
108
(d) Sealing tape or cello band (when required):
1. Improperly placed
209
2. Not covering juncture of cap and plastic
109
3. Ends overlap by less than 1 ⁄ 2 -inch
110
4. Loose or deteriorating
111
Table VIII—Rigid and Semi-Rigid Containers—Corrugated or Solid Fiberboard, Chipboard, Wood, Paperboard Aseptic Cartons, Polymeric Trays, etc. [Excluding metal, glass, and plastic]
Defects
Categories
Critical
Major
Minor
Type or size of container or component parts not as specified
None permitted
Component part missing
101
Closure not sealed, crimped, or fitted properly:
(a) Primary container
1
(b) Other than primary container
201
Dirty, stained, or smeared container
202
Wet or damp (excluding ice packs):
(a) Materially affecting appearance but not usability
203
(b) Materially affecting usability
102
Moldy area
2
Crushed or torn area:
(a) Materially affecting appearance but not usability
204
(b) Materially affecting usability
103
Separation of lamination (corrugated fiberboard):
(a) Materially affecting appearance but not usability
205
(b) Materially affecting usability
104
Product sifting or leaking
105
Nails or staples (when required):
(a) Not as required, insufficient number or improperly positioned
206
(b) Nails or staples protruding
106
Glue or adhesive (when required); not holding properly, not covering area specified, or not covering sufficient area to hold properly:
(a) Primary container
107
(b) Other than primary container
207
Flap:
(a) Projects beyond edge of container more than 1 ⁄ 4 -inch
208
(b) Does not meet properly, allowing space of more than 1 ⁄ 4 -inch
209
Sealing tape or strapping (when required):
(a) Missing
108
(b) Improperly placed or applied
210
Missing component (straw, etc.)
211
Paperboard Aseptic Cartons:
(a) Missing re-sealable cap or tab
109
(b) Inner or outer safety seal—missing, torn, poor seal
3
Thermostabilized polymeric trays:
Tray body:
(a) Swollen container
4
(b) Tear, crack, hole, abrasion through more than one layer of multi-layer laminate for the tray
5
(c) Presence of delamination in multi-layered laminate
212
(d) Presence of any permanent deformation, such that deformed area is discolored or roughened in texture
213
Lid material:
(a) Closure seal not continuous along tray flange surface
6
(b) Foldover wrinkle in seal area extends into the closure seal such that the closure seal is reduced to less than 1 ⁄ 8 -inch
7
(c) Any impression or design on the seal surfaces which conceals or impairs visual detection of seal defects
110
(d) Areas of “wave-like” striations or wrinkles along the seal area that spans the entire width of seal
214
(e) Abrasion of lid material:
1. Within 1 ⁄ 16 -inch of food product edge of seal such that barrier layer is exposed
8
2. Greater than 1 ⁄ 16 -inch from food product edge of seal that barrier layer is exposed
215
(f) Presence of entrapped matter within 1 ⁄ 16 -inch of the food product edge of seal or entrapped moisture or vapor with 1 ⁄ 16 -inch of the food product edge of seal that results in less than 1 ⁄ 16 -inch of defect free seal width at the outside edge
9
(g) Presence of any seal defect or anomaly (for example, entrapped moisture, gases, etc.) within 1 ⁄ 16 -inch of food product edge of seal
111
(h) Closure seal width less than 1 ⁄ 8 -inch
216
Table IX—Flexible Containers [Plastic, Cellophane, Paper, Textile, Laminated Multi-Layer Pouch, Bag, etc.]
Defects
Categories
Critical
Major
Minor
Type or size of container or component parts not as specified
None permitted
Closure not sealed, crimped, stitched, or fitted properly:
(a) Heat processed primary container
1
(b) Non-heat processed primary container
101
(c) Other than primary container
201
Dirty, stained, or smeared container
202
Unmelted gels in plastic
203
Torn or cut container or abrasion (non-leaker):
(a) Materially affecting appearance but not usability
204
(b) Materially affecting usability
102
Moldy area
2
Individual packages sticking together or to shipping case (tear when separated)
103
Not fully covering product
104
Wet or damp (excluding ice packs):
(a) Materially affecting appearance but not usability
205
(b) Materially affecting usability
105
Over wrap (when required):
(a) Missing
106
(b) Loose, not sealed, or closed
206
(c) Improperly applied
207
Sealing tape, strapping, or adhesives (when required):
(a) Missing
107
(b) Improperly placed, applied, torn, or wrinkled
208
Tape over bottom and top closures (when required):
(a) Not covering stitching
108
(b) Torn (exposing stitching)
109
(c) Wrinkled (exposing stitching)
110
(d) Not adhering to bag:
1. Exposing stitching
111
2. Not exposing stitching
209
(e) Improper placement
210
Product sifting or leaking:
(a) Non-heat processed
112
(b) Heat processed
3
Flexible pop-top:
(a) Poor seal (wrinkle, entrapped matter, etc.) reducing intact seal to less than 1 ⁄ 16 -inch
4
(b) Short pull tab (materially affecting usability)
212
(c) Missing pull tab
113
(d) Torn pull tab (materially affecting usability)
213
Missing component (straw, etc.)
214
Two part container (poly lined box or bag in box):
(a) Outer case torn
215
(b) Poly liner:
1. Missing
5
2. Improper closure
114
Missing “zip lock” (re-sealable containers)
216
Loss of vacuum (in vacuum-packed)
115
Pre-formed containers:
(a) Dented or crushed area
217
(b) Deformed container
218
Missing re-sealable cap
116
Inner or outer safety seal—missing, torn, poor seal
6
Air bubble in plastic
117
Thermostabilized products (includes but not limited to tubes, pouches, etc.):
Foldover wrinkle in seal area (thermostabilized pouches):
(a) Extends through all plies across seal area or reduces seal less than 1 ⁄ 16 -inch
7
(b) Does not extend through all plies and effective seal is 1 ⁄ 16 -inch or greater
219
Incomplete seal (thermostabilized pouches)
8
Non-bonding seal (thermostabilized pouches)
9
Laminate separation in body of pouch or in seal within 1 ⁄ 16 -inch of food product edge:
(a) If food contact layer is exposed
10
(b) If food contact surface is exposed after manipulation or laminate separation expands after manipulation
118
(c) If lamination separation is limited to isolated spots that do not propagate with manipulation or is outer ply separation in seal within 1 ⁄ 16 -inch of food product edge of seal
220
Flex cracks (cracks in foil layer only)
221
Swollen container
11
Blister (in seal) reducing intact seal to less than 1 ⁄ 16 -inch
12
Compressed seal (overheated to bubble or expose inner layer) reducing intact seal to less than 1 ⁄ 16 -inch
13
Stringy seal (excessive plastic threads showing at edge of seal area)
222
Contaminated seal (entrapped matter) reducing intact seal to less than 1 ⁄ 16 -inch
14
Seal creep (product in pouch “creeping” into seal) reducing intact seal to less than 1 ⁄ 16 inch
15
Misaligned or crooked seal reducing intact seal to less than 1 ⁄ 16 -inch
16
Seal formed greater than 1-inch from edge of pouch (unclosed edge flaps)
223
Waffling (embossing on surface from retort racks; not scorable unless severe)
224
Poor or missing tear notch (when required)
225
Table X—Unitizing [Plastic or other type of casing/unitizing]
Defects
Categories
Major
Minor
Not specified method
101
Missing tray (when required)
102
Missing shrink wrap (when required)
103
Loose or improperly applied wrap
201
Torn or mutilated
202
Off-center wrap (does not overlap both ends)
203
[78 FR 57041, Sept. 17, 2013]
