LEGALDIGMLEGALDIGM
    ← Code of Federal Regulations
    Beta
    7 CFR § 1767.41

    7 CFR § 1767.41 — § 1767.41 Accounting methods and procedures required of all RUS borrowers.

    Beta. Legal information, not legal advice. LEGALDIGM is not a law firm. Check the official source for the current text.

    Analyze this law with AI
    § 1767.41 Accounting methods and procedures required of all RUS borrowers. All RUS borrowers shall maintain and keep their books of accounts and all other books and records which support the entries in such books of accounts in accordance with the accounting principles prescribed in this section. Interpretations Nos. 133, 134, 137, 403, 404, 602, 606, 618, 627, 628, and 629 adopt and implement the provisions of standards issued by the Financial Accounting Standards Board (FASB). Each interpretation includes a synopsis of the requirements of the standard as well as specific accounting requirements and interpretations required by RUS. The synopsis provides general information to assist borrowers in determining whether the standard applies to an individual cooperative's operations. The synopsis is not intended to change the requirements of the FASB standards unless it is set forth in the section entitled RUS Accounting Requirements in each interpretation. If a particular borrower believes a conflict exists between the FASB standard and an RUS interpretation, the borrower shall contact the Director, PASD, to seek resolution of the issue. Numerical Index Num- ber Title 101 Work Order Procedures 102 Line Conversion 103 Sacrificial Anodes and the Replacement of a Neutral 104 Terminal Facilities 105 Pole Top Disconnect Switch 106 Steel Pole Reinforcers 107 Mobile Substations 108 Security Lights 109 Joint Use 110 First Clearing and Grading of Land and Rights of Way 111 Engineering Contracts for System Planning 112 Determination of Availability of Service 113 Temporary Facilities (Services) 114 Construction Work-in-Progress Damaged or Destroyed by Storm 115 Liquidated Damages 116 Nonrefundable Payments for Construction 117 Refunds of Overpayments for Materials and Equipment 118 Load Control Equipment 119 Special Equipment 120 Meter Sockets and Meters 121 Minimum—Maximum Voltmeters 122 Retrofitting Demand Meters 123 Transformer Conversions 124 Transclosures 125 Retirement Units 126 Establishment of Continuing Property Records 127 Continuing Property Records for Buildings 128 Sale of Property 129 Gain or Loss on the Sale of an Office Building 130 Salvage and Obsolete Material 131 Plant Acquisition Adjustments 132 General Plant 133 Plant Abandonments and Disallowances of Plant Cost 134 Utility Plant Phase-in Plans 135 Accounting for Removal or Relocation of Electric Facilities Resulting from the Action of Others 136 Storm Damage 137 Impairment of Long-Lived Assets. 138 Automatic Meter Reading Systems-Turtles. 139 Global Positioning Systems. 140 Radio-Based Automatic Meter Reading Systems. 201 Supplemental Financing 301 Forfeited Customers' Deposits 401 Computer Software Costs 402 Legal Expenses 403 Leases 404 Consolidated Financial Statements 501 Patronage Capital Assignments 502 Patronage Capital Retirements 503 Operating and Nonoperating Margins 504 Patronage Capital from G&T Cooperatives 505 Patronage Capital Furnished by Other Cooperative Service Organizations 506 Forfeited Membership Fees 601 Employee Benefits 602 Compensated Absences 603 Employee Retirement and Group Insurance 604 Deferred Compensation 605 Life Insurance Premium on Life of a Borrower Employee 606 Pension Costs 607 Unproductive Time 608 Training Costs, Attendance at Meetings, etc. 609 Maintenance and Operations 610 Financial Forecast 611 Advertising Expense 612 Special Power Cost Study 613 Mapping Costs 614 Member Relations Costs 615 Statewide Fees 616 Power Supply/Distribution Cooperative Borrowings 617 Rate Discount Allowed by the Power Cooperative to Distribution Cooperative Owning Connecting Transmission Lines 618 Theft Losses not Covered by Insurance 619 Self Billing 620 Purchase Rebates 621 Integrity Fund 622 In-Substance Defeasance 623 Satellite or Cable Television Services 624 Pollution Control Bonds 625 Prepayment of Debt 626 Rural Economic Development Loan and Grant Program 627 Postretirement Benefits 628 Postemployment Benefits 629 Investments in Debt and Equity Securities 630 Split Dollar Life Insurance. 631 Special Early Retirement Plan. 633 Cushion of Credit. Subject Matter Index Number A Abandonments—Plant 133 Acquisition Adjustments—Plant 131 Advertising Expenses 611 Assignments—Patronage Capital 501 Attendance at Meetings 608 Automatic Meter Reading Systems—Radio-Based 140 Automatic Meter Reading Systems—Turtles 138 Availability of Service—Determination of 112 B Benefits—Employee 601 Bonds—Pollution Control 624 Borrowing—Power Supply Cooperative/Distribution Cooperative 616 Buildings—Continuing Property Records 127 Buildings, Office—Gain or Loss on Sale of 129 C Cable Television Services 623 Capital Credits—Assignment 501 Capital Credits—G&T Cooperative 504 Capital Credits—Other Service Cooperatives 505 Capital Credits—Retirement 502 Compensated Absences 602 Computer Software Costs 401 Consolidated Financial Statements 404 Construction Work in Progress Damaged or Destroyed by Storm 114 Continuing Property Records—Buildings 127 Continuing Property Records—Establishment of 126 Contributions—Nonrefundable 116 Conversion—Line 102 Conversion—Transformer 123 Cushion of Credit 633 Customers' Deposits—Forfeited 301 D Damaged or Destroyed Construction Work in Progress 114 Damages—Liquidated 115 Debt—Prepayment of 625 Debt Securities—Investments in 629 Deferred Compensation 604 Demand Meters—Retrofitting 122 Determination of Availability of Service 113 Disallowances of Plant Costs 133 Disconnect Switch—Pole Top 105 Discounts Allowed by Power Cooperative to Distribution Cooperative Owning Transmission Lines 617 Distribution Cooperative/Power Supply Cooperative Borrowing 616 E Early Retirement Plan 631. Economic Development Loan and Grant Program 626 Employee Benefits 601 Equity Securities—Investments in 629 F Fees—Statewide 615 Financial Forecast 610 Financial Statements—Consolidated 404 Financing—Supplemental 201 First Clearing and Grading of Land and Rights of Way 110 Forfeited Customer Deposits 301 Forfeited Membership Fees 506 G Gain or Loss on Sale of Office Building 129 General Plant 132 Generation and Transmission (G&T) Capital Credits 504 Global Positioning Systems 139 I Impairment of Long-Lived Assets 137 In-substance Defeasance 622 Insurance—Employee Retirement and Group 603 Insurance—Premium on Life of a Borrower Employee 605 Insurance—Split Dollar 630 Integrity Fund 621 Investments in Debt and Equity Securities 629 J Joint Use 109 L Land—First Clearing and Grading 110 Leases 403 Legal Expenses 402 Life Insurance Premiums on Life of a Borrower Employee 605 Life Insurance—Split Dollar 630 Line Conversion 102 Line Relocations 135 Liquidated Damages 115 Load Control Equipment 118 Long-Lived Assets-Impairment 137 M Maintenance and Operations 609 Mapping Costs 613 Margins—Operating and Nonoperating 503 Material—Salvage and Obsolete 130 Materials and Supplies—Refund for Overpayments 117 Member Relation Costs 614 Membership Fees—Forfeited 506 Meter Reading Systems—Radio-Based 140 Meter Reading Systems—Turtles 138 Meter Sockets and Meters 120 Minimum—Maximum Voltmeters 121 Mobile Substations 107 N Neutral—Replacement of 103 Nonoperating Margins 503 Nonrefundable Payments for Construction 116 O Obsolete Material 130 Operating and Nonoperating Margins 503 Operations Costs 609 P Patronage Capital Assignments 501 Patronage Capital Furnished by Other Cooperative Service Organizations 505 Patronage Capital from G&T Cooperatives 504 Patronage Capital Retirements 502 Payments for Construction—Nonrefundable 116 Pension Costs 606 Phase-in Plans 134 Plant Abandonments 133 Plant Acquisition Adjustments 131 Plant Costs—Disallowances 133 Plant—General 132 Pole Reinforcers—Steel 106 Pole Top Disconnect Switch 105 Pollution Control Bonds 624 Postemployment Benefits 628 Postretirement Benefits 627 Power Cost Study 612 Power Supply/Distribution Cooperative Borrowing 616 Prepayment of Debt 625 Property—Sale of 128 Purchase Rebates 620 R Radio-Based Automatic Meter Reading Systems 140 Rate Discount Allowed by Power Cooperative to a Distribution Cooperative Owning Transmission Lines 617 Rebates—Purchase 620 Refunds for Overpayments for Materials and Supplies 117 Reimbursement for Line Relocations 135 Relocations of Lines 135 Replacement of a Neutral 103 Retirement Units 125 Retirements—Patronage Capital 502 Retrofitting Demand Meters 122 Rights of Way—First Clearing and Grading 110 Rural Economic Development Loan and Grant Program 626 S Sacrificial Anodes and the Replacement of a Neutral 103 Sale of an Office Building 129 Sale of Property 128 Salvage and Obsolete Material 130 Satellite Television Services 623 Securities—Investments in Debt and Equity 136 Security Lights 108 Self Billing 619 Software Costs 401 Special Early Retirement Plan 631 Special Equipment 119 Special Power Cost Study 612 Split Dollar Life Insurance 630 Statewide Fees 615 Steel Pole Reinforcers 106 Storm Damage 136 Substation—Mobile 107 Supplemental Financing 201 System Planning—Engineering Contracts 111 T Temporary Facilities (Services) 113 Terminal Facilities 104 Theft Losses not Covered by Insurance 618 Training Costs, Attendance at Meetings, etc. 608 Transclosures 124 Transformer Conversions 123 Turtles—Automatic Meter Reading Systems 138 U Unproductive Time 607 V Voltmeters—Minimum/Maximum 121 W Work Order Procedures 101 101 Work Order Procedures When a minor item of property is removed from service and not replaced, a retirement work order is not required except in the case of a conductor. The cost of the minor item shall remain in the appropriate plant account until the retirement unit, of which it is a part, is retired. However, as conductor is recorded in feet and is not part of any specific retirement unit, conductor shall be retired even though the amount taken down and not replaced is less than a retirement unit (two spans). When minor items of plant are removed and not replaced, material salvaged shall be recorded on a material salvage ticket. Items of material recorded on this ticket shall be charged to the materials and supplies account and credited in the miscellaneous columns of the Materials Register to the Accumulated Provision for Depreciation. In this example, it is assumed that the cost of removal is nil. If, however, costs are incurred during the removal of minor items of plant, these costs shall reduce the credit to the Accumulated Provision for Depreciation. When a staking sheet supporting a single work order reflects a combination of new construction and replacements, or system improvements, the predominant cost shall be the governing factor in determining the amount of cost RUS will finance. To illustrate, assume that a service is to be run to a new home near the end of an existing line. On inspection, the pole from which the service is to be run is found to be in very poor physical condition and must be replaced. In addition, a single span of wire and a service are presently connected to this pole which serve no purpose. The home originally served has been demolished and the existing span, pole, and service were retired. In other words, what started out to be simply the installation of a new service now includes the retirement of a span of wire, a pole, and a service; the replacement of a pole; and the running of a new service. Assuming the replacement of the pole is the costliest part of this project, the construction and retirement activity shall be classified as an ordinary replacement even though the work includes new construction and retirements without replacement. 102 Line Conversion If it is necessary to move a conductor from one location to another on a pole assembly during the conversion of a line from one phase to another phase, the cost of moving the conductor is capitalizable as a system improvement. 103 Sacrificial Anodes and the Replacement of a Neutral Many utilities conduct studies to determine whether sacrificial anodes are needed to protect underground cable against corrosion. The following procedures shall be followed to account for sacrificial anodes and the replacement of a neutral: 1. If the study results in the installation of sacrificial anodes, the cost of the study shall be capitalized to Account 367, Underground Conductors and Devices. If the study does not result in the installation of anodes, the cost shall be charged to Account 594, Maintenance of Underground Lines. 2. Costs incurred in the first installation are capitalizable even though anodes are considered minor items of property. However, only the first costs of installation shall be capitalized. All subsequent replacements of anodes shall be expensed. 3. Sacrificial anodes do not constitute a record unit; therefore, the cost of anodes shall be added to the cost of the underground cable unit. 4. Because a neutral is part of an underground cable record unit, and is not, in and of itself, a record unit, the cost to replace a corroded neutral shall be charged to Account 594, Maintenance of Underground Lines. 104 Terminal Facilities Borrowers are sometimes required to construct terminal facilities in the transmission line of another utility in order to receive power from their power supplier. The document executed between the borrower and the utility is normally referred to as a “License Agreement”. The license agreement may stipulate that certain items of the terminal facilities are to be transferred to, and become the property of, the other utility upon completion of the construction. The accounting for this type of transaction shall be as follows: 1. All construction costs incurred shall be charged to a work order. Upon completion of the construction and accumulation of all costs, the cost of the facilities that become the property of another utility shall be transferred from construction work-in-progress to Account 303, Miscellaneous Intangible Plant. The cost of the plant for which the borrower retains title shall be charged to the appropriate plant accounts. 2. The cost of the facilities recorded in Account 303 shall be amortized to Account 405, Amortization of Other Electric Plant, over the contract term or the estimated useful service life of the plant, whichever is shorter. If the related contract or contracts for this power supply are terminated, the unamortized balance shall be expensed, in the current period, in Account 557. 105 Pole Top Disconnect Switch The installation of pole top service disconnect switches, where title is retained by the utility, shall be capitalized in Account 371, Installations on Customers' Premises. If a switch cabinet is purchased with a current transformer included as an integral part of the cabinet, the entire cost of the switch shall be charged to Account 371. If the current transformer is installed outside of the switch cabinet, the transformer, meter, and meter base, together with the first installation costs, shall be capitalized, upon purchase, in Account 370, Meters. Payments received from the customer toward construction costs shall be credited to Account 371, Installations on Customers' Premises. Such payments, together with any amount not financed by RUS, shall be entered in column 9 of the RUS Form 219, Inventory of Work Orders. The associated maintenance costs shall be charged to Account 587, Customer Installations Expenses, or to Account 597, Maintenance of Meters, as appropriate. When pole top disconnect switches are installed and title is held by the customer, the cost of the material shall be charged to Account 456, Other Electric Revenues and the receipts from the sale of line material shall be credited to Account 456. The portion of the receipts for resale material as well as that for installation shall be credited to Account 415, Revenues from Merchandising, Jobbing, and Contract Work. The cost of resale material sold and the cost of installation shall be charged to Account 416, Costs and Expenses of Merchandising, Jobbing and Contract Work. Future maintenance costs incurred by the cooperative that are not billed to the customer shall be charged to Account 587, Customer Installations Expenses. 106 Steel Pole Reinforcers The cost associated with the purchase and installation of steel pole reinforcers shall be charged to Account 593, Maintenance of Overhead Lines. 107 Mobile Substations Mobile substations shall be accounted for in a manner similar to that for a spare and are, therefore, included as part of transmission or distribution station equipment, depending upon the use of the mobile substation. The mobile substation, together with the trailer on which it is permanently mounted, shall be capitalized upon purchase. A general purpose truck or tractor used to relocate a mobile substation and trailer shall be classified as transportation equipment. The composite depreciation rate used for transmission plant or distribution plant, as appropriate, shall be applied to the mobile substation. 108 Security Lights Where a pole supports both a secondary wire and a security light, the cost of the pole shall be charged to Account 364, Poles, Towers, and Fixtures, even though the plant investment in security lights is recorded in Account 371, Installations on Customers' Premises. 109 Joint Use There are many cases in which an electric utility and a communications utility enter into an agreement that provides for joint use of poles. Under the terms of these agreements, either utility may occupy the poles of the other upon payment of a stipulated annual rental. If such joint occupancy necessitates the use of a higher than standard pole, the new pole shall be provided at the expense of the utility having the need for the higher pole. When an electric utility replaces, at its own expense, a standard pole belonging to the communications utility with a higher pole, the cost of the higher pole, less net salvage (if any) of the pole replaced, shall be charged to the account in which the pole rental is included. Contributions made to an electric utility by a communications utility for the costs incurred in stubbing joint use electric poles shall be credited to Account 593, Maintenance of Overhead Lines. The cost of pole stubbing on electric plant distribution facilities shall be charged to Account 593. An investment in outside plant that is held in joint ownership shall be recorded in the appropriate plant accounts at its cost to the utility. For continuing property record purposes, jointly owned property units shall be priced at their cost to the utility and shall be appropriately segregated in the CPRs to indicate joint ownership. 110 First Clearing and Grading of Land and Rights of Way Utility accounting practice requires the costs associated with the first clearing and grading of land and rights of way and any resulting damage thereto, to be included in the accounts for structures and improvements or equipment to which such costs relate. Since the first clearing, as well as clearing which is “directly occasioned by the building of a structure,” is done, not for the purpose of enhancing the value of the land or the rights of way, but for the purpose of constructing plant, these costs are more directly related to the construction of plant than to the purchase of land or rights of way. The accounts shall be charged as follows: 1. For overhead transmission pole lines, Account 356, Overhead Conductors and Devices; 2. For overhead distribution lines, Account 365, Overhead Conductors and Devices; and 3. For underground distribution lines, Account 366, Underground Conduit, for a conduit installation; or Account 367, Underground Conductors and Devices, for a direct burial installation. 111 Engineering Contracts for System Planning Engineering costs for long-range system plans shall be charged to Account 183, Preliminary Survey and Investigation Charges, as incurred. The cost of engineering services incurred in preparing a long-range system plan represents a legitimate component of the total cost of construction of all system improvements detailed in the plan. The amount of engineering costs to be associated with any specific system improvement is the annual costs incurred up to the time of the allocation (not previously allocated), plus that portion of the initial cost which relates to the particular construction in question. If any major system improvement included in the engineering plan is not constructed, or if the study is superseded by another complete study, the cost of that portion of the original study not resulting in construction shall be charged to Account 182.2, Unrecovered Plant and Regulatory Study Costs, if the costs are to be recovered through future rates. Costs recorded in Account 182.2 shall be amortized to Account 407, Amortization of Property Losses, Unrecovered Plant and Regulatory Study Costs, as the costs are recovered through the rates. Any costs included in Account 182.2 that are disallowed for rate-making purposes shall be charged to Account 426.5, Other Deductions. The allocation of engineering services to the various construction projects requires the exercise of judgment. In some cases, system improvements are continuous over a period of months or years, thus permitting the engineering cost to be spread monthly as overhead in relation to the direct costs incurred in construction. (If a substantial amount of retirement work is performed in connection with system improvements, a proportionate share of the engineering cost shall be allocated on the basis of direct retirement labor.) If the system improvements detailed in the plan are not performed in a continuous manner, the engineering cost shall be allocated on the basis of the estimated costs of the various larger system improvement projects which result from the long-range plan. If construction is performed by contract, the engineering cost applicable thereto shall be transferred from Account 183 to Account 107, Construction Work-in-Progress—Electric, and thereby spread to the appropriate plant accounts on the basis of contract costs. In the case of system improvement construction performed on the basis of work orders, engineering costs shall be transferred to Account 107, Construction Work-in-Progress—Electric, and included in total work order costs as either overhead or special services. If engineering services are not readily identifiable with individual work orders, they shall be capitalized as overhead. If engineering costs for each work order are readily separable from the engineering costs for all other work orders, they shall be capitalized as special services. In summarizing system improvement work orders on the RUS Form 219, Inventory of Work Orders, the amount of engineering costs previously approved for advance on the long range plan, if any, shall be deducted to determine the balance of loan funds subject to advance by RUS. 112 Determination of Availability of Service Costs relating to the determination of availability of service, rates, and similar items for individual applicants shall be charged to Account 912, Demonstrating and Selling Expenses. If it is expected that construction will result, the costs incurred to provide service, including staking, shall be charged to Account 107, Construction Work-in-Progress—Electric. If construction does not result, Account 107 shall be credited and Account 426.5, Other Deductions, shall be charged. 113 Temporary Facilities (Services) Plant installed for temporary use, a period of less than 1.ar, shall be recorded in Account 185, Temporary Facilities, net of any payments received from customers. Upon retirement, this net cost plus cost of removal, less any salvage value, shall be cleared to Account 451, Miscellaneous Service Revenues. When a temporary service is installed at the site of a building under construction, the location of the permanent service entrance and the load and its characteristics are usually known. The temporary service is of the proper capacity and is so located or has sufficient slack, that it can be relocated to serve the new building as a permanent service. Under these conditions, the service shall be charged to Account 369, Services, when first installed. The cost of moving and attaching the service to the permanent service entrance shall be charged to Account 593, Maintenance of Overhead Lines or Account 594, Maintenance of Underground Lines, as appropriate. 114 Construction Work-in-Progress Damaged or Destroyed by Storm When installed plant, not yet completed or completed but not yet placed in service, has been damaged or destroyed by storm, the cost of the repair and restoration shall be added to the cost of construction and capitalized if the plant was constructed under force account or work order construction, and the utility paid for the cost of the repairs. If the plant was constructed under contract, the contractor is required to deliver the plant in new condition. Therefore, any repairs required prior to the completion of construction and acceptance by the utility, are ordinarily borne by the contractor. 115 Liquidated Damages Liquidated damages are amounts paid by or assessed against contractors for the completion of construction after an agreed upon date. Liquidated damages shall be credited to Account 107, Construction Work-in-Progress—Electric. Since these damages accrue during the construction period, they become one of the components of construction cost. Even though a portion of these damages may compensate the utility for costs which are not “identifiable,” no portion of the damages shall be credited to revenue or expense. When a contractor has been paid in full from loan funds or from funds to be reimbursed by loan funds without a deduction for liquidated damages, the amount of liquidated damages received shall be deposited in the Construction Fund. This amount shall be reflected by a decrease in column 5, “Total Expenditures to Date,” of the RUS Form 595, Financial Requirement and Expenditure Statement, and as an increase in column 6, “Cash Balance.” If liquidated damages are obtained by withholding an equivalent amount from the contractor's payment, the net result will be the same. 116 Nonrefundable Payments for Construction Nonrefundable payments (contributions) from customers and developers for underground construction shall first be credited to Account 107.2, Construction Work-in-Progress—Force Account. When the constructed plant is unitized and distributed to the individual plant accounts, the contributions shall be credited to those plant accounts which gave rise to the contribution. When a customer or developer furnishes a trench or other service in connection with buried plant, the cooperative shall debit Account 107.2 with the actual or estimated cost of the service performed, and account for the credit as set forth above. 117 Refunds of Overpayments for Materials and Equipment Refunds of overpayments for materials and equipment previously purchased are occasionally received as the result of legal action brought against electrical suppliers for price fixing in violation of antitrust laws. Such refunds shall be accounted for as follows: 1. The refund shall first be applied to any litigation costs that were incurred. 2. Refunds for special equipment items shall be accounted for, in detail, on the Summary of Special Equipment Costs and credited against the appropriate plant accounts. 3. Other material or equipment items that were installed through work orders or a materials furnished contract shall be adjusted on an amended work order. The amended work order shall include full details of the refund. 4. Continuing property records shall be adjusted to reflect the above transactions. 5. Amounts approved for advance on the RUS Form 595, Financial Requirement and Expenditure Statement, and on the loan budget records, shall be adjusted. For special equipment items, the adjustment shall be requested in a letter to RUS. For materials installed by work order or contract, the adjustments shall be made through credits shown on the RUS Form 219, Inventory of Work Orders. 6. Refunds for material currently in stock shall be credited to Account 154, Plant Materials and Operating Supplies. 7. If the material was used in maintenance activities or operations, the refund shall be credited to the appropriate maintenance or operations expense account. 8. Refunds for materials or equipment financed from loan funds shall be deposited in the Construction Fund—Trustee Account or remitted to RUS as a special payment on a note. Other refunds shall be deposited in the general funds. 118 Load Control Equipment The primary purpose of a Load Management System is to optimize load dispatch and to reduce or minimize system peaks in order to reduce purchases of power or to delay or eliminate the need for construction of new plant. A Load Management System may be used on integrated systems, or on generation, transmission, or distribution systems separately. The telemetry equipment used for data acquisition and interpretation may be included at various points on a system, such as generation, transmission, or distribution substation, switchyards or on consumers' premises. An effective load control program should be coordinated with the G&T and requires full participation of all member distribution systems. The G&T monitors the power load of the total member distribution system to predict the time of the system's peak load. An optimal load control strategy is developed by the G&T and is passed on from the G&T computer system to the load control computer systems of the member distribution cooperatives. The equipment at the member distribution system level is the type actually being used by an integrated power system to operate a load control program. The equipment used may vary from one integrated power system to another. The selection of equipment used is determined by the information needs of the integrated power system, and the method selected to operate the load control system. Some equipment performs only SCADA-type functions. This equipment is included with the equipment that performs only load control functions because SCADA-type equipment is an integral part of a load control program. An effective load control strategy requires current information on loads so that member distribution systems can determine the actual loads to be shed and the duration of the load control. The function and location of the load control equipment are the primary factors in determining the account in which the equipment shall be recorded. The following example depicts a common load control system and the associated accounting. Equipment type may vary, thereby necessitating the use of accounts not prescribed below. In all instances, however, the function and location of the equipment shall dictate the appropriate account classification. G&T Borrower 1. Coordinating System Equipment Coordinating System Equipment is the data acquisition, processing and control hardware and software used to coordinate the load control efforts of the member distribution system. Generally, this equipment is dedicated to load control use and is not shared with other electric utility activities. The purpose of the G&T load control computer system is to reduce or minimize the peak power requirements of the entire member distribution system. This involves load dispatching to control transmission circuits and breakers. The computer system for load control shall, therefore, be recorded in Account 353, Station Equipment, with the associated operating expenses recorded in Account 561, Load Dispatching, and maintenance expenses recorded in Account 570, Maintenance of Station Equipment. 2. Coordinating System Communications Link The G&T load control computer system is usually linked to the load control computer system for each member distribution system by a radio or telephone link that is dedicated to that purpose and is not shared with other communication activities. Under such circumstances, communications equipment shall be classified in Account 353, Station Equipment. If the communications equipment is shared with general use or voice communications equipment, however, the equipment shall be classified in Account 397, Communication Equipment. 3. Depreciation Load control equipment shall be recorded in separate subaccounts of the primary plant accounts detailed above and shall be depreciated based upon the owner's estimate of the equipment's useful service life. Distribution Borrower 1. Member System Equipment Member system equipment is the data acquisition, processing and control hardware and software used as a subset to the overall load control efforts by the integrated power system. The member system computer for each distribution member system accepts the control strategy from the G&T coordinating system and develops the tables that determine the control loads that are to be shed and the duration of the load control. The member system computer for each distribution system monitors the usage at each of its delivery points. This usage data is then transmitted to the G&T coordinating system for use in developing load projects and evaluating control strategies for the integrated power system. The member system computer is generally dedicated to load control use and is not shared with other electric utility operations. The member computer system shall be recorded in Account 362, Station Equipment. The associated operating expenses shall be recorded in Account 581, Load Dispatching, and maintenance expenses shall be recorded in Account 592, Maintenance of Station Equipment. 2. Substation Remote Controllers Substation Remote Controllers are located at the distribution substation. They accept control signals from the member system computer and couple the signal to the portion of the distribution system to which it is connected. Substation Remote Controllers also serve as a receiver of inbound signals from transponders located in the distribution system. They also send data back to the member system computer. Substation Remote Controllers shall be recorded in Account 362, Station Equipment. The associated operating expenses shall be recorded in Account 582, Station Expenses, and maintenance expenses shall be recorded in Account 592, Maintenance of Station Equipment. 3. Substation Injection Units Substation Injection Units are used only in power line based systems and are located in distribution substations. A major function of the Substation Injection Unit is to receive load control signals from the member system computer and inject them into the power line based system to be transmitted to the Load Control Receivers. Substation Injection Units can also perform control and SCADA functions similar to those performed by Substation Remote Controllers. Substation Injection Units shall be recorded in Account 362, Station Equipment. The associated operating expenses shall be recorded in Account 582, Station Expenses, and maintenance expenses shall be recorded in Account 592, Maintenance of Station Equipment. 4. Remote Terminal Units Remote Terminal Units perform electric utility SCADA functions in a distribution substation or delivery point. These functions include monitoring equipment for abnormal operating conditions, monitoring analog quantities such as conductor voltage or substation load, and controlling of certain equipment within the substation. Remote Terminal Units shall be recorded in Account 362, Station Equipment. The associated operating expenses shall be recorded in Account 582, Station Expenses, and maintenance expenses shall be recorded in Account 592, Maintenance of Station Equipment. 5. Line Device Transponder A Line Device Transponder directly controls a piece of distribution apparatus, such as a voltage regulator or a power factor correction capacitor, located on a distribution feeder and not accessible to a Remote Terminal Unit. The Line Device Transponder actuates the control functions and reports back to the member system computer upon completion of the requested action. This transponder is located at the site of the distribution apparatus being controlled. Line Device Transponders shall be recorded in Account 368, Line Transformers. The associated operating expense shall be recorded in Account 583, Overhead Line Expenses, or Account 584, Underground Line Expenses, as appropriate, and maintenance expenses shall be recorded in Account 595, Maintenance of Line Transformers. 6. Communications Verification Transponders Communication Verification Transponders are used to respond to inquiries from Substation Remote Controllers. In power line based systems, these transponders are used to verify the performance of the communications system. They are also used during adverse system operations to isolate sections of the distribution system that are experiencing an outage. Communication Verification Transponders shall be recorded in Account 362, Station Equipment. The associated operating expenses shall be recorded in Account 582, Station Expenses, and maintenance expenses shall be recorded in Account 592, Maintenance of Station Equipment. 7. Load Control Receivers The Load Control Receiver, also known as a load control switch, is located at the site of the consumer's load. These receivers directly control the electric supply to an end-use appliance, such as an electric water heater, central air conditioning compressor, or irrigation pump. The amount of time that an appliance will be turned off by the load control receiver is preset. When the member system computer determines that load shedding is necessary, it sends a signal to the communication link which then sends signals directly to the Load Control Receivers. In a power line based system, the signal from the communications link is sent by radio or telephone line to the Substation Injection Units, which then signals the Load Control Receivers to shut down the appliances for the present time. In nonpower line based systems, the signal from the communications link is sent by radio directly to the Load Control Receivers. Load Control Receivers are located on the consumer's side of the meter. When the member distribution system retains title to the Load Control Receivers and assumes full responsibility for maintenance and replacement of the equipment, it shall be classified in Account 371, Installations on Customer's Premises. Load Control Receivers that are donated or given to consumers shall be charged to Account 908, Customer Assistance Expenses. Operating and maintenance expenses applicable to Load Control Receivers recorded in Account 371 shall be charged to Account 587, Customer Installations Expenses, and Account 598, Maintenance of Miscellaneous Distribution Plant, respectively. Expenses applicable to Load Control Receivers donated or given to consumers shall be recorded in Account 908, Customer Assistance Expenses. Load Control Receivers may be moved on a continual basis from one customer location to another and are, therefore, considered to be special equipment items. When ownership is maintained by the member distribution cooperative, Load Control Receivers shall be accounted for in accordance with the special equipment procedures outlined in Accounting Interpretation No. 119 of this section. 8. Communication Links The communication link in the member distribution systems between the Member System Computer, the Substation Remote Controllers or Substation Injection Units, Remote Terminal Units, Line Device Transponders, Communication Verification Transponders, and Load Control Receivers is usually accomplished by radio, telephone line, or power line based system. The communication links are normally dedicated to the SCADA and load control functions being served. Under such circumstances, communications equipment shall be recorded in Account 362, Station Equipment. If, however, the communication equipment used is shared with general use or voice communications equipment, the equipment shall be charged to Account 397, Communication Equipment. 9. Depreciation Load control equipment shall be recorded in separate subaccounts of the primary plant accounts detailed above and shall be depreciated based upon the manufacturer's estimate of the equipment's useful service life. 119 Special Equipment Special Equipment items are classified separately from work order items. The USoA provides accounting that differs from that used for other types of materials. The cost of new, special equipment items shall be capitalized at the time of purchase; it shall not be charged to Account 154 as is the case with other materials. The first installation cost, as well as all incidental costs necessary to prepare the equipment for use, shall be capitalized with the material upon purchase. All subsequent costs of removing, resetting, changing, renewing oil, and repairing constitute operations and maintenance expenses. The capitalized cost of special equipment items, including the first installation, shall be removed from the electric plant accounts only when the items are abandoned or retired from the system. Borrowers may request a waiver from the special equipment accounting requirements as described later in this section. Special Equipment Items include the following: 1. Reclosers and Sectionalizers recorded in Account 365, Conductor and Devices 2. Transformers, Capacitors and Voltage Regulators recorded in Account 368, Line Transformers 3. Meters, Meter Sockets, current and potential transformers, and other metering equipment recorded in Account 370, Meters. 4. Load Control Devices recorded in Account 371, Installations on Customers' Premises (See Interpretation No. 118) Note: Equipment installed in a substation is not considered special equipment. Special equipment items which are classified as nonusable shall be segregated in the warehouse and retired from service. The Summary of Special Equipment Costs shall be retitled Summary of Special Equipment Costs Retired and used for this purpose. A journal entry reflecting this information shall be prepared and posted to the books. Since loan funds for special equipment, including first installation costs, are approved for advance by the Rural Development upon receipt of the borrower's written estimate of funds required, and not on the basis of an Inventory of Work Orders, it is improper to take a credit for any salvage involved in the retirement of special equipment on the Inventory of Work Orders. Electric borrowers that wish to receive a waiver from the special equipment accounting requirements should submit a letter request to Rural Development. In order to expedite these requests the letter to Rural Development should state that the borrower will adhere to the following requirements to account for special equipment using the work order procedure rather than the special equipment accounting procedures prescribed by Rural Development: 1. New purchases of special equipment items are to be charged to Account 154, Materials and Supplies, upon purchase. 2. Labor, material and overhead costs associated with the initial installation and all subsequent installations of special equipment are recorded on construction work orders and charged to the appropriate plant accounts upon closeout of the construction work order. 3. Labor and overhead costs associated with the removal of special equipment items, whether the items removed are placed in inventory or permanently retired and disposed of, are recorded on retirement work orders and charged or credited to the depreciation reserve account upon closeout of the retirement work order. 4. The special equipment items retired and salvaged for reuse are returned to the materials and supplies account at the average material cost in the materials and supplies account and credited to the depreciation reserve upon closeout of the retirement work order. In addition to recognition of the requirements noted above, the borrower should indicate how it plans to account for the items of special equipment that have been charged to the plant accounts but not installed (in inventory). Two acceptable methods to account for this equipment are: (1) Leave the equipment in the plant accounts until the inventory is depleted and charge only new purchases to materials and supplies, or (2) credit the plant accounts for the installed cost of the equipment in inventory, charge the equipment cost to materials and supplies, and charge the installation cost to the appropriate operations expense account. Also, under the second method, the borrower must submit a “negative” special equipment summary to Rural Development to return to the balance in reserve for the current loan the installed cost of special equipment in inventory on the date of transition. 120 Meter Sockets and Meters When a utility furnishes meter sockets, ownership by the utility of the meter socket or base, as well as the meter itself, is established by virtue of them being furnished without cost to the consumer by the cooperative. While no agreement as to ownership between the cooperative and the property owner exists, cooperative ownership is implied by long standing practice and tradition in the electric utility industry. 121 Minimum—Maximum Voltmeters A minimum—maximum voltmeter is used to record the minimum and maximum voltages at a specific line location over a period of time. It is normally installed on a pole in connection with a 1 1/2 kVA transformer, a meter base and connecting wires, and other small items of materials. Meter bases are ordinarily set for these voltmeters throughout the system, and a lesser number of voltmeters are rotated among them periodically to obtain voltage readings. An average system may have one voltmeter to two installations, with a maximum of 20 or 25 voltmeters for the whole system. Minimum—maximum voltmeters shall be recorded, through work orders, in Account 370, Meters, when installed. The cost of the transformers shall remain in Account 368, Line Transformers, with the cost of the meter bases remaining in Account 370, Meters. The miscellaneous material used in installing the transformer and the meter base shall be charged to Account 370, Meters. Maintenance expense shall be charged to either Account 595, Maintenance of Line Transformers, or Account 597, Maintenance of Meters, as appropriate. Costs associated with reading the voltmeters shall be charged to Account 583, Overhead Line Expenses, and the cost of relocating or changing the complete installation or any part thereof, other than retirement of the meter base, shall be charged to Account 583, Overhead Line Expenses, or Account 586, Meter Expenses. 122 Retrofitting Demand Meters A demand meter measures the amount of electricity used over a period of time in kilowatt-hours (kWh) and indicates the maximum kilowatts (kW) required at any one time by means of a pointer. Electronic or solid state demand meters have a direct readout which reads kilowatt demand to two decimal places. The use of a direct readout demand meter may result in increased revenues as pointer readings tend to register lower than actual usages. The process of retrofitting a demand meter replaces the pointer with a direct readout. The cost of such a replacement is usually expensed as a minor item of property; however, since the use of a direct readout results in a substantial betterment, the excess cost of the replacement over the estimated cost, at current prices, of replacing the pointer without the betterment is capitalized. 123 Transformer Conversions The …

    Related guides, FAQ and contract templates