Beta
za:gov:merchant-shipping-safe-containers-convention-act-10-2011-14-jul-2011
za:gov:merchant-shipping-safe-containers-convention-act-10-2011-14-jul-2011 — Merchant Shipping (Safe Containers Convention) Act 10 of 2011
Beta. Legal information, not legal advice. LEGALDIGM is not a law firm. Check the official source for the current text.
Analyze this law with AIPlease note that most Acts are published in English and another South African
official language. Currently we only have capacity to publish the English versions.
This means that this document will only contain even numbered pages as the other
language is printed on uneven numbered pages.
Government Gazette
REPUBLIC OF SOUTH AFRICA
Vol. 553 Cape Town 14 July 2011 No. 34460
THE PRESIDENCY
No. 581 -XO\
It is hereby notified that the President has assented to the following Act,
which is hereby published for general information:–
No. 10 of 2011: Merchant Shipping (Safe Containers Convention) Act, 2011.
AIDS HELPLINE: 0800-123-22 Prevention is the cure
2 No. 34460 GOVERNMENT GAZETTE. 14JULY 2011
ActNo.10of2011 MERCHANT SIIIPPING (SAFE CONTAINERS CONVENTION) ACT, 2011
(English text signed by the President)
(Assented to 13 July 20/1)
ACT
To give effect to the International Convention for Safe Containers, and to provide
for matters connected therewith.
E IT ENACTED by the Parliament of the Republic of South Africa, as
B follows:-
Definitions
I. (I) In this Act, unless the context indicates otherwise-
" Authority" means the South African Maritime Safety Authority established by 5
section 2(1) of the South African Maritime Safety Authority Act. 1998 (Act No. 5
of 1998);
"container" means a container as defined in the Convention and to which the
Convention applies;
4
'Contracting State" means a state specified in a notice under section 4; 10
"inspector" means a person appointed as an inspector under section 6;
"Minister" means the Minister of Transport;
"organ of state" has the same meaning assigned to it in section 239 of the
Constitution of the Republic of South Africa, 1996;
"the Convention" means the International Convention for Safe Containers set out 15
in the Schedule;
"the Republic" includes the Prince Edward Islands referred to in section 3;
"this Act" includes the regulations.
(2) In this Act, unless the context indicates otherwise, any word or expression to
which a meaning has been assigned by the Convention, has the same meaning as in the 20
Convention.
Act binds State
2. This Act binds the State and every organ of state.
Application of Act
3. (I) This Act extends to the Prince Edward Islands as defined in section I of the 25
Prince Edward Islands Act, 1948 (Act No. 43 of 1948).
(2) In its application to those islands, transport between the Republic and the Prince
Edward Islands is not international transport.
Declaration of Contracting States
4. (I) The Minister may. by notice in the Gazette, declare a state, other than the 30
Republic, specified in the notice as a State Party to the Convention.
4 No. 34460 GOVERNMENT GAZETTE, 14 JULY 20 II
Act No. 10 of2011 MERCHANT SIIIPPING (SAFE CONTAINERS CONVENTION) ACT, 2011
(2) A notice under subsection (I) is evidence that a state specified in such notice is a
State Party to the Convention.
Certain provisions of Convention have force of law
5. Subject to this Act, Articles II to VI of the Convention have the force of law in the
Republic. 5
Inspectors
6. (I) The Authority may appoint as an inspector any person who is qualified to be so
appointed, to perform any of the functions assigned to an inspector in terms of this Act.
(2) The Authority must issue to each inspector a certificate in the prescribed form,
stating that he or she has been appointed as an inspector. 10
(3) When boarding any vehicle or entering any premises contemplated in section 7(1),
an inspector must, on request, show the certificate to the person in charge of the vehicle
or premises.
Powers of inspectors
7. (I) In addition to any powers that he or she may have under the regulations, an 15
inspector may, without a warrant, at any reasonable time-
( a) board any vehide, including a ship, train, truck or aircraft, or enter any
premises if he or she believes on reasonable grounds that-
(i) there is significant evidence that the condition of a container in or on such
vehicle or premises creates an obvious risk to safety; 20
(ii) there is a container in or on such vehicle or premises, for the purpose of
verifying as to whether such container carries a valid Safety Approval
Plate as required by the Convention; or
(iii) a provision of this Act has been contravened; and
(b) examine any record or document and make copies or extracts of such a record 25
or document, found in such a vehicle, ship, train, truck, aircraft or premises.
(2) The owner or person in charge of any vehicle boarded or premises entered by an
inspector and every person in such vehicle or on such premises, must give the inspector
all reasonable assistance to enable the inspector to perform his or her functions under
this Act and must provide the inspector with any information that the inspector may 30
reasonably require with respect to the administration of this Act.
(3) An entry and inspection of premises without a warrant must be carried out only
during normal hours of business and with the consent of the owner or person in control
of the premises.
Obstruction of inspectors 35
8. (1) No person may obstruct or hinder an inspector in the performance of his or her
functions under this Act.
(2) No person may knowingly make any false or misleading statement, either orally
or in writing, to an inspector engaged in the performance of his or her functions under
this Act. 40
(3) No person may remove or interfere in any way with a container detained by an
inspector in terms of this Act, unless authorised by an inspector.
Inquiry into accident or incident
9. ( 1) If an accident or incident involving a container results in death or injury to any
person, danger to the health or safety of the public or damage to property or the 45
6 No. 34460 GOVERNMENT GAZETTE, 14 JULY 20 II
Act No. 10 of2011 MERCHANT SHIPPING (SAFE CONTAINERS CONVENTION) ACT, 2011
environment, the Authority may direct an inquiry to be conducted into the accident or
incident by any suitable person, authorised by the Authority.
(2) The person authorised by the Authority under subsection (1) has all the powers
conferred upon a court of marine enquiry by section 9( 1) and (4) of the Merchant
Shipping Act, 1951 (Act No. 57 of 1951), and subsections (2) and (3) of that section 5
apply accordingly.
(3) The person authorised to conduct an inquiry must, as soon as possible after
conclusion of that inquiry, submit a report with recommendations to the Authority,
together with all the evidence and other material that was before the inquiry.
(4) The Authority must publish the report within 60 days of receipt, unless the report 10
contains a recommendation that a publication be withheld in the public interest, in which
case the Authority may withhold publication of the report in whole or in part as it deems
fit.
(5) The Authority may supply copies of a published report in the manner and on the
terms that it deems proper. 15
Regulations
10, (1) The Minister may make regulations-
(a) regarding the detention and transportation of containers that do not carry a
valid Safety Approval Plate as required by the Convention;
(b) regarding the detention and transportation of containers in respect of which 20
there is significant evidence that the condition of the container creates an
obvious risk to safety;
(c) regarding the maintenance and repair of containers;
(d) pertaining to the circumstances under which and the manner in which the
Authority may dispose of detained containers that have not been reclaimed; 25
(e) requiring that the Safety Approval Plate affixed to any or all containers
approved in terms of this Act be in one or more of the official languages of the
Republic;
(f) prescribing matters required or permitted by this Act to be prescribed; and
(g) generally with regard to any other incidental administrative or procedural 30
matter necessary to prescribe for the proper implementation of this Act.
(2) (a) The Minister may incorporate all or part of any health and safety standard,
without re-stating the text thereof, in a regulation by referring to the number, title and
year of issue of that health and safety standard or to any other particular by which that
health and safety standard is sufficiently identified. 35
(b) Whenever a health and safety standard referred to in paragraph (a) is subsequently
amended or substituted, the amended health and safety standard is, in the absence of a
contrary intention, deemed to have been incorporated in terms of the regulation
contemplated in paragraph (a).
(c) A copy of a full text of a health and safety standard incorporated in terms of 40
paragraph (a) and any amendment or substitution thereof, must be kept at a place in the
Republic that the Authority directs and must be available for public inspection.
(d) Section 28 of the Standards Act, 2008 (Act No. 8 of 2008), does not apply to any
incorporation of a health and safety standard or to any amendment or substitution of a
health and safety standard under this section. 45
8 No. 34460 GOVERNMENT GAZETTE, 14 JULY 2011
Act No. 10 of2011 MERCHANT SHIPPING (SAFE CONlAINERS CONVENTION)ACT, 2011
Offences and penalties
11. (I) A person who contravenes this Act commits an offence and is liable upon
conviction to a fine or to imprisonment for a period not exceeding two years.
(2) Without affecting the jurisdiction of any coun existing apan from this subsection,
a court has jurisdiction over an offence in terms of this Act if- 5
(a) the offence was committed in the territorial jurisdiction of that court; or
(b) the accused is found or carries on business in the territorial jurisdiction of that
court.
(3) If a person-
( a) admits to the Authority that he or she has contravened this Act; 10
(b) agrees to abide by the decision of the Authority; and
(c) deposits with the Authority such amount of money as may be determined by
the Authority, which amount must not exceed the maximum fine that may be
imposed under subsection (I),
the Authority may, after any inquiry that it deems fit, determine the matter summarily 15
and may, without legal proceedings, order the whole or any pan of the deposit to be
forfeited by way of a penalty.
(4) A person may appeal to the Minister against a determination or order of the
Authority.
(5) An appeal must be lodged within 90 days from the date of the determination or 20
order.
(6) The imposition of a penalty under subsection (3) must not be regarded as a
conviction for an offence, and no prosecution in respect of the offence in question may
thereafter be instituted.
(7) All fines and other money penalties imposed under this Act must be paid to the 25
Authority for the benefit of the Maritime Fund established by section 38 of the South
African Maritime Safety Authority Act, 1998 (Act No.5 of 1998).
Duration of Act
12. This Act continues in force until a date fixed by the President by proclamation in
the Gazette following denunciation of the Convention by the Republic or the 30
termination thereof in accordance with Anicle XII of the Convention.
Repeal of Act 11 of 1985
13. The International Convention for Safe Containers Act, 1985 (Act No. ll of 1985),
is repealed.
Short title and commencement 35
14. This Act is called the Merchant Shipping (Safe Containers Convention) Act, 2011,
and comes into operation on a date fixed by the President by proclamation in the
Gazette.
10 No. 34460 GOVERNMENTGAZETTE,I4JULY2011
Act No. 10 of2011 MERCHANT SIIIPPING (SAFE CONTAINERS CONVENTION)ACI; 2011
SCHEDULE
(Section 1)
INTERNATIONAL CONVENTION FOR SAFE CONTAINERS
PREAMBLE
THE CONTRACTING PARTIES, 5
RECOGNISING the need to maintain a high level of safety of human life in the
handling, stacking and transporting of containers,
MINDFUL of the need to facilitate international container transport,
RECOGNISING, in this context, the advantages of formal ising common international
safety requirements, 10
CONSIDERING that this end may best be achieved by the conclusion of a convention,
HAVE DECIDED to formalise structural requirements to ensure safety in the handling,
stacking and transporting of containers in the course of normal operations, and to this
end HAVE AGREED as follows:
ARTICLE I 15
General obligation under the present Convention
The Contracting Parties undertake to give effect to the provisions of the present
Convention and the Annexes hereto, which shall constitute an integral part of the present
Convention.
ARTICLE II 20
Definitions
For the purpose of the present Convention, unless expressly provided otherwise:
1. ~'Container" means an article of transport equipment:
(a) of a permanent character and accordingly strong enough to be suitable for
repeated use; 25
(b) specially designed to facilitate the transport of goods, by one or more modes
of transport, without intermediate reloading;
(c) designed to be secured and/or readily handled, having corner fittings for these
purposes;
(d) of a size such that the area enclosed by the four outer bottom corners is either: 30
(i) at least 14m 2 (150 sq ft), or
(ii) at least 7 m 2 (75 sq ft) if it is fitted with top corner fittings.
The term "container" includes neither vehicles nor packaging; however, containers
when carried on chassis arc included.
2. "Corner fittings" means an arrangement of apertures and faces at the top and/or 35
bottom of a container for the purposes of handling, stacking and/or securing.
3. "Administration" means the Government of a Contracting Party under whose
authority containers are approved.
4. '"Approved" means approved by the Administration.
12 No. 34460 GOVERNMENT GAZETTE, 14 JULY 20 II
Act No. 10 of2011 MERCIIANT SHIPPING (SAFE CONTAINERS CONVENTION) ACT, 201 I
5. "Approval" means the decision by an Administration that a design type or a
container is safe within the terms of the present Convention.
6. "International transport" means transport between points of departure and
destination situated in the territory of two countries to at least one of which the present
Convention applies. The present Convention shall also apply when part of a transport 5
operation between two countries takes place in the territory of a country to which the
present Convention applies.
7. "Cargo" means any goods, wares, merchandise and articles of every kind
whatsoever carried in the containers.
8. "New container" means a container the construction of which was commenced on 10
or after the date of entry into force of the present Convention.
9. "Existing container" means a container which is not a new container.
10. "Owner" means the owner as provided for under the national law of the
Contracting Party or the lessee or bailee, if an agreement between the parties provides
for the exercise of the owner's responsibility for maintenance and examination of the 15
container by such lessee or bailee.
11. "Type of container" means the design type approved by the Administration.
12. "Type-series container" means any container manufactured in accordance with
the approved design type.
13. "Prototype" means a container representative of those manufactured or to be 20
manufactured in a design type series.
14. ''Maximum operating gross weight" or "rating" or "R" means the maximum
allowable combined weight of the container and its cargo.
15. "Tare weight" means the weight of the empty container including permanently
affixed ancillary equipment. 25
16. "Maximum permissible payload" or "P" means the difference between
maximum operating gross weight or rating and tare weight.
ARTICLE III
Application
I. The present Convention applies to new and existing containers used in international 30
transport, excluding containers specially designed for air transport.
2. Every new container shall be approved in accordance with the provisions either for
type-testing or for individual testing as contained in Annex I.
3. Every existing container shall be approved in accordance with the relevant
provisions for approval of existing containers set out in Annex I within five years from 35
the date of entry into force of the present Convention.
ARTICLE IV
Testing, inspection, approval and maintenance
1. For the enforcement of the provisions of Annex I every Administration shall
establish an effective procedure for the testing, inspection and approval of containers in 40
accordance with the criteria established in the present Convention, provided, however,
that an Administration may entrust such testing, inspection and approval to
organisations duly authorised by it.
2. An Administration which entrusts such testing, inspections and approval to an
organisation shaH inform the Secretary-General of the Inter-Governmental Maritime 45
Consu1tative Organisation (hereinafter referred to as "the Organisation") for commu-
nication to Contracting Parties.
3. Application for approval may be made to the Administration of any Contracting
Party.
14 No. 34460 GOVERNMENT GAZETTE, 14 JULY 2011
Act No. 10 of2011 MERCHANT SHIPPING (SAFE CONTAINERS CONVENTION) ACT, 2011
4. Every container shall be maintained in a safe condition in accordance with the
provisions of Annex I.
5. If an approved container does not in fact comply with the requirements of Annexes
I and II the Administration concerned shall take such steps as it deems necessary to bring
the container into compliance with such requirements or to withdraw the approval. 5
ARTICLE V
Acceptance of approval
I. Approval under the authority of a Contracting Party. granted under the terms of the
present Convention, shall be accepted by the other Contracting Parties for all purposes
covered by the present Convention. It shall be regarded by the other Contracting Parties 10
as having the same force as an approval issued by them.
2. A Contracting Party shall not impose any other structural safety requirements or
tests on containers covered by the present Convention, provided, however, that nothing
in the present Convention shall preclude the application of provisions of national
regulations or legislation or of international agreements, prescribing additional 15
structural safety requirements or tests for containers specially designed for the transport
of dangerous goods, or for those features unique to containers carrying bulk liquids or
for containers when carried by air. The term "dangerous goods" shall have that meaning
assigned to it by international agreements.
ARTICLE VI 20
Control
I. Every container which has been approved under Article III shall be subject to
control in the territory of the Contracting Parties by officers duly authorised by such
Contracting Parties. This control shall be limited to verifying that the container carries
a valid Safety Approval Plate as required by the present Convention, unless there is 25
significant evidence for believing that the condition of the container is such as to create
an obvious risk to safety. In that case the officer carrying out the control shall only
exercise it in so far as it may be necessary to ensure that the container is restored to a safe
condition before it continues in service.
2. Where the container appears to have become unsafe as a result of a defect which 30
may have existed when the container was approved, the Administration responsible for
that approval shall be inforrned by the Contracting Party which detected the defect.
ARTICLE VII
Signature, ratification, acceptance, approval and accession
I. The present Convention shall be open for signature until 15 January 1973 at the 35
Office of the United Nations at Geneva and subsequently from I February 1973 until 31
December 1973 inclusive at the Headquarters of the Organisation at London by all
States Members of the United Nations or Members of any of the specialised agencies or
of the International Atomic Energy Agency or Parties to the Statute of the International
Court of Justice, and by any other State invited by the General Assembly of the United 40
Nations to become a Party to the present Convention.
2. The present Convention is subject to ratification, acceptance or approval by States
which have signed it.
3. The present Convention shaH remain open for accession by any State referred to in
paragraph I. 45
4. Instruments of ratification. acceptance, approval or accession shall be deposited
with the Secretary-General of the Organisation (hereinafter referred to as "the
Secretary-General").
16 No. 34460 GOVERNMENT GAZETTE, 14 JULY 20 II
Act No. 10 of2011 MERCHANT SHIPPING (SAfE CONTAINERS CONVENTION) ACT, 2011
ARTICLE VIII
Entry into force
I. The present Convention shall enter into force twelve months from the date of the
deposit of the tenth instrument of ratification, acceptance, approval or accession.
2. For each State ratifying, accepting, approving or acceding to the present 5
Convention after the deposit of the tenth instrument of ratification, acceptance, approval
or accession, the present Convention shall enter into force twelve months after the date
of the deposit by such State of its instrument of ratification, acceptance, approval or
accession.
3. Any State which becomes a Party to the present Convention after the entry into 10
force of an amendment shall, failing an expression of a different intention by that State,
(a) be considered as a Party to the Convention as amended; and
(b) be considered as a Party to the unamended Convention in relation to any Party
to the Convention not bound by the amendment.
ARTICLE IX 15
Procedure for amending any part or parts of the present Convention
1. The present Convection may be amended upon the proposal of a Contracting Party
by any of the procedures specified in this Article.
2. Amendment after consideration in the Organisation:
(a) Upon the request of a Contracting Party, any amendment proposed by it to the 20
present Convention shall be considered in the Organisation. If adopted by a
majority of two thirds of those present and voting in the Maritime Safety
Committee of the Organisation, to which all Contracting Parties shall have
been invited to participate and vote, such amendment shall be communicated
to all Members of the Organisation and all Contracting Parties at least six 25
months prior to its consideration by the Assembly of the Organisation. Any
Contracting Party which is not a Member of the Organisation shall be entitled
to participate and vote when the amendment is considered by the Assembly.
(b) If adopted by a two-thirds majority of those present and voting in the
Assembly, and if such majority includes a two-thirds majority of the 30
Contracting Parties present and voting, the amendment shall be communi-
cated by the Secretary-General to all Contracting Parties for their acceptance.
(c) Such amendment shall come into force twelve months after the date on which
it is accepted by two thirds of the Contracting Parties. The amendment shall
come into force with respect to all Contracting Parties except those which, 35
before it comes into force, make a declaration that they do not accept the
amendment.
3. Amendment by a conference:
Upon the request of a Contracting Party, concurred in by at least one third of the
Contracting Parties, a conference to which the States referred to in Article VII shall be 40
invited wi11 be convened by the Secretary-GeneraL
I8 No. 34460 GOVERNMENT GAZETTE, 14 JULY 2011
Acl No. 10 of2011 MERCHANT SHIPPING (SAFE CONTAINERS CONVENTION) ACT, 2011
ARTICLE X
Special procedure for amending the Annexes
I. Any amendment to the Annexes proposed by a Contracting Party shall be
considered in the Organisation at the request of that Party.
2. If adopted by a two-thirds majority of those present and voting in the Maritime 5
Safety Committee of the Organisation to which all Contracting Parties shall have been
invited to participate and to vote, and if such majority includes a two-thirds majority of
the Contracting Parties present and voting, such amendment shall be communicated by
the Secretary-General to all Contracting Parties for their acceptance.
3. Such an amendment shall enter into force on a date to be determined by the 10
Maritime Safety Committee at the time of its adoption unless, by a prior date determined
by the Maritime Safety Committee at the same time, one fifth or five of the Contracting
Parties, whichever number is less, notify the Secretary-General of their objection to the
amendment.
Determination by the Maritime Safety Committee of the dates referred to in this 15
paragraph shall be by a two-thirds majority of those present and voting, which majority
shall include a two-thirds majority of the Contracting Parties present and voting.
4. On entry into force any amendment shall, for all Contracting Parties which have not
objected to the amendment, replace and supersede any previous provision to which the
amendment refers; an objection made by a Contracting Party shall not be binding on 20
other Contracting Parties as to acceptance of containers to which the present Convention
applies.
5. The Secretary-General shall inform all Contracting Parties and Members of the
Organisation of any request and communication under this Article and the date on which
any amendment enters into force. 25
6. Where a proposed amendment to the Annexes has been considered but not adopted
by the Maritime Safety Committee, any Contracting Party may request the convening of
a conference to which the States referred to in Article VII shall be invited. Upon receipt
of notification of concurrence by at least one third of the other Contracting Parties, such
a conference shall be convened by the Secretary-General to consider amendments to the 30
Annexes.
ARTICLE XI
Denunciation
l. Any Contracting Party may denounce the present Convention by effecting the
deposit of an instrument with the Secretary-General. The denunciation shall take effect 35
one year from the date of such deposit with the Secretary-General.
2. A Contracting Party which has communicated an objection to an amendment to the
Annexes may denounce the present Convention and such denunciation shall take effect
on the date of entry into force of such an amendment.
ARTICLE XII 40
Termination
The present Convention shall cease to be in force if the number of Contracting Parties
is less than five for any period of twelve consecutive months.
20 No. 34460 GOVERNMENT GAZETTE, 14 JULY 20 II
Act No. 10 of20ll MERCHANT SHIPPING (SAFE CONTAINERS CONVENTION) ACT, 2011
ARTICLE XIII
Settlement of disputes
l. Any dispute between two or more Contracting Parties concerning the interpretation
or application of the present Convention which cannot be settled by negotiation or other
means of settlement shall, at the request of one of them, be referred to an arbitration 5
tribunal composed as follows: each party to the dispute shall appoint an arbitrator and
these two arbitrators shall appoint a third arbitrator, who shall be Chairman. If, three
months after receipt of a request, one of the parties has failed to appoint an arbitrator or
if the arbitrators have failed to elect the Chairman, any of the parties may request the
Secretary-General to appoint an arbitrator or the Chairman of the arbitration tribunal. 10
2. The decision of the arbitration tribunal established under the provisions of
paragraph I shall be binding on the parties to the dispute.
3. The arbitration tribunal shall determine its own rules of procedure.
4. Decisions of the arbitration tribunal, both as to its procedures and its place of
meeting and as to any controversy laid before it, shall be taken by majority vote. 15
5. Any controversy which may arise between the parties to the dispute as regards the
interpretation and execution of the award may be submitted by any of the parties for
judgment to the arbitration tribunal which made the award.
ARTICLE XIV
Reservations 20
1. Reservations to the present Convention shall be permitted, excepting those relating
to the provisions of Articles I to VI, XIII, the present Article and the Annexes, on
condition that such reservations are communicated in writing and, if communicated
before the deposit of the instrument of ratification, acceptance, approval or accession,
are confirmed in that instrument. The Secretary-General shall communicate such 25
reservations to all States referred to in Artic1e VII.
2. Any reservation made in accordance with paragraph l:
(a} modifies for the Contracting Party which made the reservation the provisions
of the present Convention to which the reservation relates to the extent of the
reservation; and 30
(b) modifies those provisions to the same extent for the other Contracting Parties
in their relations with the Contracting Party which entered the reservation.
3. Any Contracting Party which has formulated a reservation under paragraph l may
withdraw it at any time by notification to the Secretary-General.
ARTICLE XV 35
Notification
In addition to the notifications and communications provided for in Articles IX, X and
XIV, the Secretary-General shall notify all the States referred to in Article VII of the
following:
(a) signatures, ratifications, acceptances, approvals and accessions under Article 40
VII:
(b) the dates of entry into force of the present Convention in accordance with
Article VIII:
(c) the date of entry into force of amendments to the present Convention m
accordance with Articles !X and X: 45
(d) denunciations under Article XI;
(e) the termination of the present Convention under Article XII.
22 No. 34460 GOVERNMENT GAZETTE, 14 JULY 2011
Act No. 10 of2011 MERCHANT SHIPPING (SAFE CONTAINERS CONVENTION) ACT, 201 I
ARTICLE XVI
Authentic texts
The original of the present Convention, of which the Chinese, English, French, Russian
and Spanish texts are equally authentic, shall be deposited with the Secretary-General,
who shall communicate certified true copies to all States referred to in Article VII. 5
IN WITNESS WHEREOF the undersigned Plenipotentiaries, being duly authorised
thereto by their respective Governments, have signed the present Convention.
DONE at Geneva this second day of December, one thousand nine hundred and
seventy-two.
24 No. 34460 GOVERNMENT GAZETTE, I4 JULY 20II
Act No. 10 of2011 MERCHANT SHIPPING (SAFE CONTAINERS CONVENTION) ACT, 20II
ANNEX I
REGULATIONS FOR THE TESTING, INSPECTION, APPROVAL AND
MAINTENANCE OF CONTAINERS
CHAPTER I
REGULATIONS COMMON TO ALL SYSTEMS OF APPROVAL 5
Safety Approval Plate
l. (I) (a) A Safety Approval Plate conforming to the specifications set out in the
Appendix to this Annex shall be permanently affixed to every approved container at a
readily visible place, adjacent to any other approval plate issued for official purposes,
where it would not be easily damaged. 10
(b) On each container, all maximum gross weight markings shall be consistent with
the maximum gross weight information on the Safety Approval Plate.
(c) The owner of the container shall remove the Safety Approval Plate on the
container if:
(i) the container has been modified in a manner which would void the original 15
approval and the information found on the Safety Approval Plate; or
(ii) the container is removed from service and is not being maintained in
accordance with the Convention; or
(iii) the approval has been withdrawn by the Administration.
(2) (a) The plate shall contain the following information in at least the English or 20
French language:
"CSC SAFETY APPROVAL"
Country of approval and approval reference
Date (month and year) of manufacture
Manufacturer's identification number of the container or, in the case of existing 25
containers for which that number is unknown, the number a11otted by the
Administration
Maximum operating gross weight (kg and lb)
Allowable stacking weight for I ,8 g (kg and lb)
Transverse racking test load value (kg and lb ). 30
(h) A blank space should be reserved on the plate for insertion of end-wall and/or
side-wa11 strength values (factors) in accordance with paragraph 3 of this Regulation and
Annex II, tests 6 and 7. A blank space should also be reserved on the plate for the first
and subsequent maintenance examination dates (month and year) when used.
(3) Where the Administration considers that a new container satisfies the require- 35
ments of the present Convention in respect of safety and if, for such container, the
end-wall and/or side-wall strength values (factors) are designed to be greater or less than
those stipulated in Annex II, such values shall be indicated on the Safety Approval Plate.
(4) The presence of the Safety Approval Plate docs not remove the necessity of
displaying such labels or other information as may be required by other regulations 40
which may be in force.
Maintenance and examination
2. (1) The owner of the container shall be responsible for maintaining it in safe
condition.
(2) (a) The owner of an approved container shall examine the container or have it 45
examined in accordance with the procedure either prescribed or approved by the
Contracting Party concerned, at intervals appropriate to operating conditions.
(h) The date (month and year) before which a new container shall undergo its first
examination shall be marked on the Safety Approval Plate.
26 No. 34460 GOVERNMENT GAZETTE, 14 JULY 20 II
Act No. 10 of2011 MERCHANT SHIPPING (SAFE CONTAINERS CONVENTION) ACT, 2011
(c) The date (month and year) before which the container shall be re-examined shall
be clearly marked on the container on or as dose as practicable to the Safety Approval
Plate and in a manner acceptable to that Contracting Party which prescribed or approved
the particular examination procedure involved.
(d) The interval from the date of manufacture to the date of the first examination shall 5
not exceed five years. Subsequent examination of new containers and re-examination of
existing containers shall be at intervals of not more than 30 months. All examinations
shall determine whether the container has any defects which could place any person in
danger.
(3) (a) As an alternative to paragraph 2, the Contracting Party concerned may approve 10
a continuous examination programme if satisfied, on evidence submitted by the owner,
that such a programme provides a standard of safety not inferior to the one set out in
paragraph 2 above.
(b) To indicate that the container is operated under an approved continuous
examination programme, a mark showing the letters "ACEP" and the identification of 15
the Contracting Party which has granted approval of the programme shall be displayed
on the container on or as close as practicable to the Safety Approval Plate.
(c) All examinations performed under such a programme shall determine whether a
container has any defects which could place any person in danger. They shall be
performed in connection with a major repair, refurbishment, or on-hire/off hire 20
interchange and in no case less than once every 30 months.
(4) For the purpose of this Regulation "the Contracting Party concerned" is the
Contracting Party of the territory in which the owner is domiciled or has his head office.
However, in the event that the owner is domiciled or has his head office in a country the
government of which has not yet made arrangements for prescribing or approving an 25
examination scheme and until such time as the arrangements have been made, the owner
may use the procedure prescribed or approved by the Administration of a Contracting
Party which is prepared to act as the Contracting Party concerned. The owner shall
comply with the conditions for the use of such procedures set by the Administration in
question. 30
CHAPTER II
REGULATIONS FOR APPROVAL OF NEW CONTAINERS BY DESIGN TYPE
Approval of new containers
3. To qualify for approval for safety purposes under the present Convention all new
containers shall comply with the requirements set out in Annex IT. 35
Design type approval
4. In the case of containers for which an application for approval has been submitted,
the Administration will examine designs and witness testing of a prototype container to
ensure that the containers will conform with the requirements set out in Annex II. When
satisfied, the Administration shall notify the applicant in writing that the container meets 40
the requirements of the present Convention and this notification shall entitle the
manufacturer to affix the Safety Approval Plate to every container of the design type
series.
Provisions for approval by design type
5. (1) Where the containers are to be manufactured by design type series, application 45
made to an Administration for approval by design type shall be accompanied by
drawings, a design specification of the type of container to be approved and such other
data as may be required by the Administration.
28 No. 34460 GOVERNMENT GAZETTE, 14 JULY 20 II
Act No. 10 of2011 MERCHANT SHIPPING (SAFE CONTAINERS CONVENTION) ACT, 2011
(2) The applicant shall state the identification symbols which will be assigned by the
manufacturer to the type of container to which the application for approval relates.
(3) The application shall also be accompanied by an assurance from the manufacturer
that he will:
(a) produce to the Administration such containers of the design type concerned as 5
the Administration may wish to examine;
(b) advise the Administration of any change in the design or specification and
await its approval before affixing the Safety Approval Plate to the container;
Ic) affix the Safety Approval Plate to each container in the design type series and
to no others; lO
(d) keep a record of containers manufactured to the approved design type. This
record shall at least contain the manufacturer's identification numbers, dates
of delivery and names and addresses of customers to whom the containers are
delivered.
(4) Approval may be granted by the Administration to containers manufactured as 15
modifications of an approved design type if the Administration is satisfied that the
modifications do not affect the validity of tests conducted in the course of design type
approval.
(5) The Administration shall not confer on a manufacturer authority to affix Safety
Approval Plates on the basis of design type approval unless satisfied that the 20
manufacturer has instituted internal production-control features to ensure that the
containers produced will conform to the approved prototype.
Examination during production
6. In order to ensure that containers of the same design type series are manufactured
to the approved design, the Administration shaH examine or test as many units as it 25
considers necessary, at any stage during production of the design type series concerned.
Notification of Administration
7. The manufacturer shaH notify the Administration prior to commencement of
production of each new series of containers to be manufactured in accordance with an
approved design type. 30
CHAPTER III
REGULATIONS FOR APPROVAL OF NEW CONTAINERS BY INDIVIDUAL
APPROVAL
Approval of individual containers
8. Approval of individual containers may be granted where the Administration, after 35
examination and witnessing of tests, is satisfied that the container meets the
requirements of the present Convention; the Administration, when so satisfied, shall
notify the applicant in writing of approval and this notification shall entitle him to affix
the Safety Approval Plate to such container.
30 No. 34460 GOVERNMENT GAZETTE, 14 JULY 2011
Act No. 10 of2011 MERCHANT SHIPPING (SAFE CONTAINERS CONVENTION) ACT, 2011
CHAPTER IV
REGULATIONS FOR APPROVAL OF EXISTING CONTAINERS AND NEW
CONTAINERS NOT APPROVED AT TIME OF MANUFACTURE
Approval of existing containers
9. (I) If, within five years from the date of entry into force of the present Convention, 5
the owner of an existing container presents the following information to an
Administration:
(a) date and place of manufacture;
(b) manufacturer's identification number of the container, if available;
(c) maximum operating gross weight capability; I0
(d) (i) evidence that a container of this type has been safely operated in
maritime and/or inland transport for a period of at least two years; or
(ii) evidence to the satisfaction of the Administration that the container was
manufactured to a design type which had been tested and found to
comply with the technical conditions set out in Annex II, with the 15
exception of those technical conditions relating to the end-wall and
side-wall strength tests; or
(iii) evidence that the container was constructed to standards which, in the
opinion of the Administration, were equivalent to the technical condi-
tions set out in Annex II, with the exception of those technical conditions 20
relating to the end-wall and side-wall strength tests;
(e) allowable stacking weight for 1,8 g (kg and lb); and
(f) such other data as required for the Safety Approval Plate,
then the Administration, after investigation, shal1 notify the owner in writing whether
approval is granted; and if so, this notification shall entitle the owner to affix the Safety 25
Approval Plate after an examination of the container concerned has been carried out in
accordance with Regulation 2. The examination of the container concerned and the
affixing of the Safety Approval Plate shall be accomplished not later than I January
1985.
(2) Existing containers which do not qualify for approval under paragraph l of this 30
Regulation may be presented for approval under the provisions of Chapter II or Chapter
III of this Annex. For such containers the requirements of Annex II relating to cnd-wal1
and/or side-wall strength tests shall not apply. The Administration may, if it is satisfied
that the containers in question have been in service, waive such of the requirements in
respect of presentation of drawings and testing, other than the lifting and floor-strength 35
tests, as it may deem appropriate.
Approval of new containers not approved at time of manufacture
10. Tf, on or before 6 September 1982, the owner of a new container which was not
approved at the time of manufacture presents the following information to an
Administration: 40
(a) date and place of manufacture;
(b) manufacturer's identification number of the container, if available;
(c) maximum operating gross weight capability;
(d) evidence to the satisfaction of the Administration that the container was
manufactured to a design type which has been tested and found to comply 45
with the technical conditions set out in Annex II;
(e) allowable stacking weight for 1,8 g (kg and lb ); and
(f) such other data as required for the Safety Approval Plate,
the Administration, after investigation, may approve the container, notwithstanding the
provisions of Chapter II. Where approval is granted, such approval shall be notified to 50
the owner in writing, and this notification shall entitle the owner to affix the Safety
32 No. 34460 GOVERNMENT GAZETTE, 14JULY2011
Act No. 10 of20ll MERCHANT SHIPPING (SAFE CONTAINERS CONVENTION) ACI; 2011
Approval Plate after an examination of the container concerned has been carried out in
accordance with Regulation 2. The examination of the container concerned and the
affixing of the Safety Approval Plate shall be accomplished not later than I January
1985.
CHAPTERV 5
REGULATIONS FOR APPROVAL OF MODIFIED CONTAINERS
Approval of modified containers
11. The owner of an approved container that has been modified in a manner resulting
in structural changes shall notify the Administration or an approved organization duly
authorized by it of those changes. The Administration or authorized organization may I 0
require retesting of the modified container as appropriate prior to recertification.
34 No. 34460 GOVERNMENT GAZETTE, 14 JULY 20 II
Act No.IO of2011 MERCHANT SHIPPING (SAFE CONTAINERS CONVENTION) ACT, 20 II
APPENDIX
The Safety Approval Plate, confonning to the model reproduced below, shall take the
form of a permanent, non-corrosive, fireproof rectangular plate measuring not less than
200 mm x 100 mm. The words "CSC SAFETY APPROVAL", of a minimum letter
height of 8 mm, and all other words and numbers of a minimum height of 5 mm shall be 5
stamped into, embossed on or indicated on the surface of the plate in any other
pennanent and legible way.
CSC SAFETY APPROVAL
2
$100 mm 7
10
1 [GB-Ln49/217n5)
2 DATE MANUFACTURED
3... IDENTIFICATION No.
4 ... MAXIMUM GROSS 15
WEIGHT ....... kg ....... lb
5... ALLOWABLE STACKING WEIGHT
6... FOR 1,8 g ..... kg ......•• Ib
7... RACKING TEST LOAD
VALUE ....... kg ....... lb
8...
9... 20
2
$200 mm 7
I. Country of approval and approval reference as given in the example on line I. (The
country of approval should be indicated by means of the distinguishing sign used to
indicate country of registration of motor vehicles in international road traffic.)
2. Date (month and year) of manufacture.
3. Manufacturer's identification number of the container or, in the case of existing 25
containers for which that number is unknown, the number allotted by the Administra-
tion.
4. Maximum operating gross weight (kg and lb ).
5. Allowable stacking weight for 1,8 g (kg and lb).
6. Transverse racking test load value (kg and lb ). 30
7. End-wall strength to be indicated on plate only if end-walls are designed to
withstand a load of 1css or greater than 0,4 times the maximum permissible payload, i.e.
0,4 P.
36 No. 34460 GOVERNMENT GAZETTE, 14 JULY 2011
Act No. 10 of2011 MERCHANT SHIPPING (SAFE CONTAINERS CONVENTION) ACT, 2011
8. Side-wall strength to be indicated on plate only if the side-walls are designed to
withstand a load of Jess or greater than 0,6 times the maximum permissible payload, i.e.
0,6 P.
9. First maintenance examination date (month and year) for new containers and
subsequent maintenance examination dates (month and year) if plate is used for this 5
purpose.
38 No. 34460 GOVERNMENT GAZETTE, 14 JULY 2011
Act No. 10 of2011 MERCHANT SHIPPING (SAFE CONTAINERS CONVENTION) ACT, 2011
ANNEX II
STRUCTURAL SAFETY REQUIREMENTS AND TESTS
Introduction
In setting the requirements of this Annex, it is implicit that in all phases of the
operation of containers the forces as a result of motion, location, stacking and weight of 5
the loaded container and external forces will not exceed the design strength of the
container. In particular, the following assumptions have been made:
(a) the container will so be restrained that it is not subjected to forces in excess of
those for which it has been designed;
(b) the conlainer will have its cargo stowed in accordance with the recommended 10
practices of the trade so that the cargo does not impose upon the container
forces in excess of those for which it has been designed.
Construction
1. A container made from any suitable material which satisfactorily performs the
following tests without sustaining any permanent deformation or abnonnality which I 5
would render it incapable of being used for its designed purpose shall be considered safe.
2. The dimensions, positioning and associated tolerances of corner fittings shall be
checked having regard to the lifting and securing systems in which they will function.
Test loads and test procedures
Where appropriate to the design of the container, the following test loads and test 20
procedures shall be applied to all kinds of containers under test:
1. LIFTING
The container, having the prescribed internal loading, shall be 1ifted in such a way that
no significant acceleration forces are applied. After lifting, the container shall be
suspended or supported for five minutes and then lowered to the ground. 25
(A) Lifting from corner fittings
TEST LOADINGS AND APPLIED TEST PROCEDURES
FORCES
Internal loading: (i) Lifting from top corner fittings:
A uniformly distributed load such that Containers greater than 3 000 mm
the combined weight of container and (I 0 ft) (nominal) in length shall have
test load is equal to 2 R. In the case of a lifting forces applied vertically at all four
tank-container, when the test weight of top comer fittings.
the internal load plus the tare weight is Containers of 3 000 mm (10ft)
less than 2 R, a supplementary load (nominal) in length or less shall have
distributed over the length of the tank is lifting forces applied at all four top
to be applied to the container. comer fillings, in such a way that the
angle between each lifting device and the
vertical shall be 30°.
40 No. 34460 GOVERNMENT GAZETTE, 14 JULY 2011
Ad No. 10 of2011 MERCHANT SHIPPING (SAFE CONTAINERS CONVENTION) ACT, 2011
TEST LOADINGS AND APPLIED TEST PROCEDURES
FORCES
Externally applied forces: (ii) Lifting from bottom corner fittings:
Such as to lift the combined weight of Containers shall have lifting forces
2 R in the manner prescribed (under the applied in such a manner that the lifting
heading TEST PROCEDURES). devices bear on the bottom comer fittings
only. The lifting forces shall be applied at
angles to the horizontal of:
30° for containers of length 12 000 mm
(40ft) (nominal) or greater, 37' for
containers of length 9 000 mm (30 ft)
(nominal) and up to but not including
12 000 mm (40 ft) (nominal), 45' for con-
tainers of length 6 000 mm (20 ft) (nomi-
nal) and up to but not including 9 000 mm
(30ft) (nominal), 60' for containers of
less than 6 000 mm (20 ft) (nominal).
(B) Lifting by any other additional methods
TEST LOADINGS AND APPLIED TEST PROCEDURES
FORCES
Internal loading: (i) Lifting from fork-lift pockets:
A uniformly distributed load such that The container shall be placed on bars
the combined weight of container and which are in the same horizontal plane,
test load is equal to I ,25 R. In the case of one bar centred within each fork-lift
a tank-container, when the test weight of pocket which is used for lifting the loaded
the internal load plus the tare weight is container. The bars shall be of the same
less than I ,25 R, a supplementary load width as the forks intended to be used in
distributed over the length of the tank is the handling, and shall project into the
to be applied to the container. fork pocket 75% of the length of the fork
pocket.
Externally applied forces: (ii) L!fting f'om grappler arm positions:
Such as to lift the combined weight of The container shall be placed on pads in
1,25 R in the manner prescribed (under the same horizontal plane, one under
the heading TEST PROCEDURES). each grappler arm position. These pads
shall be of the same sizes as the lifting
area of the grappler arms intended to be
used.
(iii) Other methods:
Where containers are designed to be
lifted in the loaded condition by any
method not mentioned in (A) or (B)(i)
and (ii) they shall also be tested with the
internal loading and externally applied
forces representative of the acceleration
conditions appropriate to that method.
42 No. 34460 GOVERNMENT GAZETTE, 14 JULY 2011
Act No.IO of2011 MERCHANT SHIPPING (SAFE CONTAINERS CONVENTION) ACT, 2011
2.STACKING
2.1 For conditions of international transport where the maximum vertical acceleration
forces vary significantly from 1,8 g and when the container is reliably and effectively
limited to such conditions of transport, the stacking load may be varied by the
appropriate ratio of acceleration forces.
2.2 On successful completion of this test the container may be rated for the allowable
superimposed static stacking weight, which should be indicated on the Safety Approval
Plate against the heading ALLOWABLE STACKING WEIGHT FOR 1,8 g (kg and lb).
TEST LOADINGS AND APPLIED TEST PROCEDURES
FORCES
Internal loading:
A uniformly distributed load such that The container, having the prescribed
the combined weight of container and internal loading, shall be placed on four
test load is equal to I ,8 R. Tank-contain- level pads which are in turn supported on
ers may be tested in the tare condition. a rigid horizontal surface, one under each
bottom comer titling or equivalent corner
structure. The pads shall be centralized
under the fittings and shall be of appro xi-
mately the same plan dimensions as the
fittings.
Externally applied forces:
Such as to subject each of the four top Each externally applied force shall be
comer fittings to a vertical downward applied to each of the corner fittings
force equal to 0.25 x I ,8 x the allowable through a corresponding test comer
superimposed static stacking weight. fitting or through a pad of the same plan
dimensions. The test corner fitting or pad
shall be offset with respect to the top
corner fitting of the container by 25 mm
(I in) laterally and 38 mm (I Vz in)
longitudinally.
3. CONCENTRATED LOADS
TEST LOADINGS AND APPLIED TEST PROCEDURES
FORCES
(a) On roof
Internal loading:
None.
Externally applied forces:
A concentrated load of 300 kg The externally applied forces shall be
(660 lb) uniformly distributed over an applied vertically downwards to the outer
area of 600 mm x 300 mm (24 in x surface of the weakest area of the roof of
12 in). the container.
44 No. 34460 GOVERNMENT GAZETTE, 14 JULY 2011
Act No.IO of2011 MERCHANT SHIPPING (SAFE CONIAINERS CONVENTION)ACT, 2011
TEST LOADINGS AND APPLIED TEST PROCEDURES
FORCES
(b) On floor
Internal loading:
Two concentrated loads, each of 2 730 The test should be made with the
kg (6 000 lb) and each applied to the container resting on four level supports
container floor through a contact area of under its four bottom corners in such a
142 cm2 (22 sq in). manner that the base structure of the
container is free to deflect.
A testing device loaded to a weight of
5 460 kg (12 000 lb), that is 2 730 kg
(6 000 lb) on each of two surfaces,
having, when loaded, a total contact area
of 284 cm 2 (44 sq in), that is 142 cm 2
(22 sq in) on each surface, the surface
width being 180 mm (7 in) spaced
760 mm (30 in) apart, centre to centre,
should be manoeuvred over the entire
floor area of the container.
Externally applied forces:
None.
4. TRANSVERSE RACKING
TEST LOADINGS AND APPLIED TEST PROCEDURES
FORCES
Internal loading:
None. The container in tare condilion shall be
placed on four level supports, one under
each bottom comer, and shall be
restrained against lateral and vertical
movement by means of anchor devices
so arranged that the lateral restraint is
provided only at the bottom comers
diagonally opposite to those at which the
forces are applied.
Externally applied forces:
Such as to rack the end structures of the The externally applied forces shall be
container sideways. The forces shall be applied either separately or simulta-
equal to those for which the container neously to each of the top comer fittings
was designed. on one side of the container in lines
parallel both to the base and to the planes
of the ends of the container. The forces
shall be applied first towards and then
away from the top comer fittings. In the
case of containers in which each end is
symmetrical about its own vertical
centerline, one side only need be tested,
but both sides of containers with
asymmetric ends shall be rested.
46 No. 34460 GOVERNMENT GAZETTE, 14 JULY 20 II
Act No. 10 of 2011 MERCHANT SHIPPING (SAFE CONTAINERS CONVENTION) ACT, 2011
5. LONGITUDINAL RESTRAINT (STATIC TEST)
When designing and constructing containers, it must be borne in mind that containers,
when carried by inland modes of transport, may sustain accelerations of 2 g applied
horizontally in a longitudinal direction.
TEST LOADINGS AND APPLIED TEST PROCEDURES
FORCES
Internal loading:
A uniformly distributed load. such that The container, having the prescribed
the combined weight of a container and internal loading, shall be restrained
test load is equal to the maximum longitudinally by securing the two
operating gross weight or rating, R. In bottom comer fittings or equivalent
the case of a tank-container, when the comer structures at one end to suitable
weight of the internal load plus the tare anchor points.
is less than the maximum gross weight
or rating, R, a supplementary load is to
be applied to the container.
Externally applied forces:
Such as to subject each side of the The externally applied forces shall be
container to longitudinal compressive applied first towards and then away
and tensile forces of magnitude R, that from the anchor points. Each side of the
is, a combined force of 2 R on the base container shall be tested.
of the container as a whole.
6. END-WALLS
The end-walls should be capable of withstanding a load of not less than 0,4 times the
maximum permissible payload. If, however, the end-walls are designed to withstand a
load of less or greater than 0,4 times the maximum permissible payload, such a strength
factor shall be indicated on the Safety Approval Plate in accordance with Annex I,
Regulation I.
TEST LOADINGS AND APPLIED TEST PROCEDURES
FORCES
Internal loading:
Such as to subject the inside of an end- The prescribed internal loading shall be
wall to a uniformly distributed load of applied as follows:
0,4 P or such other load for which the Both ends of a container shall be tested
container may be designed. except that where the ends are identical
only one end need be tested. The end-
walls of containers which do not have
open sides or side doors may be tested
separately or simultaneously.
The end-walls of containers which do
have open sides or side doors should be
tested separately. When the ends are
tested separately the reactions to the
forces applied to the end-wall shall be
confined to the base structure of the
container.
48 No. 34460 GOVERNMENT GAZETTE, 14 JULY 2011
Act No. tO of20ll MERCHANT SHIPPING (SAFE CONTAINERS CONVENTION)ACT, 2011
TEST LOADINGS AND APPLIED TEST PROCEDURES
FORCES
Externally applied forces:
None.
7. SIDE-WALLS
The side-walls should be capable of withstanding a load of not less than 0,6 times the
maximum permissible payload. If, however, the side-walls are designed to withstand a
load of less or greater than 0,6 times the maximum permissible payload, such a strength
factor shall be indicated on the Safety Approval Plate in accordance with Annex I,
Regulation I.
TEST LOADINGS AND APPLIED TEST PROCEDURES
FORCES
Internal loading:
Such as to subject the inside of a side- The prescribed internal loading shall be
wall to a uniformly distributed load of applied as follows:
0,6 P or such other load for which the Both sides of a container shall be tested
container may be designed. except that where the sides are identical
only one side need be tested. Side-walls
shall be tested separately and the
reactions to the internal loading shall be
confined to the comer fittings or equiva-
Jent comer structures. Open-topped con-
tainers shall be tested in the condition in
which they are designed to be operated,
for example, with removable top mem-
hers in position.
Externally applied forces:
None.
