Beta
pk:federal:UY2FqaJw1-apaUY2Fqa-b56X
pk:federal:UY2FqaJw1-apaUY2Fqa-b56X — Factories Act, 1934
Beta. Legal information, not legal advice. LEGALDIGM is not a law firm. Check the official source for the current text.
Analyze this law with AITHE FACTORIES ACT, 1934
CONTENTS
CHAPTER I
PRELIMINARY
1.
Short title, extent and commencement
2.
Definitions
3.
References to time of day
4.
Seasonal factories
5.
Power to apply provisions applicable to factories to certain other places
6.
Power to declare departments to be separate factories
7.
Power to exempt on a change in the factory
7A.
Exemption from certain provisions of the Act
8.
Power to exempt during public emergency
9.
Notice to Inspector before commencement of work
CHAPTER II
THE INSPECTING STAFF
10.
Inspectors
11.
Powers of Inspector
12.
Certifying surgeons
CHAPTER III
HEALTH AND SAFETY
13.
Cleanliness
14.
Disposal of wastes and effluents
15.
Ventilation and temperature
16.
Dust and fume
17.
Artificial humidification
18.
Overcrowding
19.
Lighting
20.
Drinking water
21.
Latrines and urinals
22.
Spittoons
23.
Precaution against contagious or infectious disease
23A.
Compulsory vaccination and inoculation
24.
Power to make rules for the provision of canteens
24A.
Welfare Officer
25.
Precautions in case of fire
26.
Fencing of machinery
27.
Work on or near machinery in motion
28.
Employment of young persons on dangerous machines
29.
Striking gear and devices for cutting off power
30.
Self-acting machines
31.
Casing of new machinery
32.
Prohibition of employment of women and children near cotton openers
33.
Cranes and other lifting machinery
33A.
Hoists and lifts
33B.
Revolving machinery
33C.
Pressure plant
33D.
Floors, stairs and means of access
33E.
Pits, sumps, opening in floors, etc.
33F.
Excessive weights
33G.
Protection of eyes
33H.
Powers to require specifications of defective parts or tests of stability
33I.
Safety of building, machinery and manufacturing process
33J.
Power to make rules to supplement this Chapter
33K.
Precautions against dangerous fumes
33L.
Explosive or inflammable dust, gas, etc.
33M. Power to exclude children
33N.
Notice of certain accident
33P.
Appeals
33Q.
Additional power to make health and safety rules relating to shelters during rest
CHAPTER IV
RESTRICTIONS ON WORKING HOURS OF ADULTS
34.
Weekly hours
35.
Weekly holiday
35A.
Compensatory holidays
36.
Daily hours
37.
Intervals for rest
38.
Spread over
39.
Notice of periods for Work for Adults and preparation thereof
40.
Copy of Notice of Periods for Work to be sent to Inspector
41.
Register of Adult Workers
42.
Hours of work to correspond with Notice under section 39 and Register under section 41
43.
Power to make rules exempting from restrictions
44.
Power to make orders exempting from restrictions
45.
Further restrictions on the employment of women
46.
Special provision for night-shifts
47.
Extra pay for overtime
48.
Restriction on double employment
49.
Control of overlapping shifts
CHAPTER IVA
HOLIDAYS WITH PAY
49A.
Application of Chapter
49B.
Annual holidays
49C.
Pay during annual holidays
49D.
Payment when to be made
49E.
Power of Inspector to act for worker
49F.
Power to make rules
49G.
Exemption of factories from the provisions of this Chapter
49H.
Casual leave and sick leave
49I.
Festival holidays
CHAPTER V
SPECIAL PROVISIONS FOR ADOLESCENTS AND CHILDREN
50.
Prohibition of employment of young children
51.
Non-adult workers to carry tokens giving reference to certificates of fitness
52.
Certificates of fitness
53.
Effect of certificate granted to adolescent
54.
Restrictions on the working hours of a child
55.
Notice of Periods for Work for Children
56.
Register of Child Workers
57.
Hours of work to correspond with Notice and Register
58.
Power to require medical examination
59.
Power to make rules
59A.
Provisions to be in addition to Act XXVI of 1938
CHAPTER VI
PENALTIES AND PROCEDURE
60.
Penalty for contraventions of Act and rules
61.
Enhanced penalty in certain cases after previous conviction
62.
Penalty for failure to give notice of commencement of work or of change of manager
63.
Penalty for obstructing Inspector
64.
Penalty for failure to give notice of accidents
65.
Penalty for failure to make returns
66.
Penalty for smoking or using naked light in vicinity of inflammable material
67.
Penalty for using false certificate
68.
Penalty on guardian for permitting double employment of a child
69.
Penalty for failure to display certain notices
Determination of “occupier” for purposes of this Chapter
71.
Exemption of occupier or manager from liability in certain cases
72.
Presumption as to employment
73.
Evidence as to age
74.
Cognizance of offences
75.
Limitation of prosecutions
CHAPTER VII
SUPPLEMENTAL
Display of factory notices
77.
Power of Provincial Government to make rules
78.
[Repealed.]
79.
Publication of rules
80.
Application to Government factories
81.
Protection to persons acting under this Act
82.
[Repealed.]
[Repealed.]
THE FACTORIES ACT, 1934
ACT NO. XXV OF 1934
[20th August, 1934]
An Act to consolidate and amend the law regulating labour in factories.
WHEREAS it is expedient to consolidate and amend the law regulating labour in factories ;
It is hereby enacted as follows :___
CHAPTER I
PRELIMINARY
1. Short title, extent and commencement.___(1) This Act may be called the Factories Act,
1934.
[(2) It extends to the whole of Pakistan.]
(3) It shall come into force on the 1st day of January, 1935.
2. Definitions.___In this Act, unless there is anything repugnant in the subject or context,___
(a)
“adolescent” means a person who has completed his fifteenth but has not
completed his seventeenth year ;
(b)
“adult” means a person who has completed his seventeenth year ;
(c)
“child” means a person who has not completed his fifteenth year ;
(d)
“day” means a period of twenty-four hours beginning at midnight ;
(e)
“week” means a period of seven days beginning at midnight on Saturday night ;
(f)
“power” means electrical energy, and any other form of energy which is
mechanically transmitted and is not generated by human or animal agency ;
The Act has been applied to Phulera in the Excluded Area of Upper Tanawal to the extent the Act is applicable in the N.W.F.P., subject to certain
modifications, see N.W.F.P. (Upper Tanawal) (Excluded Area) Laws Regulation, 1950, and extended to the Excluded Area of Upper Tanawal (N.W.F.P.)
other than Phulera with effect from such date and subject to such modifications as may be notified, see N.W.F.P. (Upper Tanawal) (Excluded Area) Laws
Regulation, 1950.
The Act in its application in the Punjab has been amended by Factories (Punjab Amdt.) Act, 1940 (Punjab 7 of 1940), in N.W.F.P., by the Factories (NorthWest Frontier Province Amdt.) Act, 1940 (N.W.F.P.7 of 1947),
___
This Act has been extended to the
(i) Leased Areas of Baluchistan, see the Leased Areas (Laws) Order, 1950 (G.G.O.3 of 1950); and also applied in the Federated Areas of Baluchistan, see
Gazette of India, 1937, Pt.I, p.1499;
(ii) Baluchistan States Union, see the Baluchistan States Union (Federal Laws) (Extension) Order, 1953 (G.G.O.4 of 1953), as amended;
(iii) Khairpur State, see G.G.O.5 of 1953, as amended; and
(iv) State of Bahawalpur by the Bahawalpur (Extension of Federal Laws) Order, 1953 (G.G.O.11 of 1953), as amended.
The Act has been and shall be deemed to have been brought into force in Gwadur, (w. e. f. the 18th September, 1958), by the Gwadur (Application of
Central Laws) Ordinance, 1960 (37 of 1960),s.2
The Act has been applied to the Provincially Administrated Tribal Areas or to the parts or those areas to which it does not already, apply see Regulation
No. I of 1972, s.2 and Sch.
Subs. by the Central Laws (Statute Reform) Ordinance, 1960 (Ordinance No. XXI of 1960), s.3 and Sch. 2., (w. e. f. the 14th October, 1955).
(g)
“manufacturing process” means any process___
(i)
for making, altering, repairing, ornamenting, finishing or packing, or
otherwise treating any article or substance with a view to its use, sale,
transport, delivery or disposal, or
(ii)
for pumping oil, water or sewage, or
(iii)
for generating, transforming or transmitting power ;
(h)
“worker” means a person employed 1[directly or through an agency], whether
for wages or not, in any manufacturing process, or in cleaning any part of the
machinery or premises used for a manufacturing process, or in any other kind
of work whatsoever incidental to or connected with the manufacturing process
or connected with the subject of the manufacturing process, but does not include
any person solely employed in a clerical capacity in any room or place where
no manufacturing process is being carried on ;
(j)
“factory” means any premises including the precincts thereof whereon 1[ten] or
more workers are working, or were working on any day of the preceding twelve
months, and in any part of which a manufacturing process is being carried on
[or is ordinarily carried on whether with or without the aid of power] ;
but does not include a mine subject to the operation of the Mines Act, 1923 (IV of
1923).
(k)
“machinery” includes all plant whereby power is generated, transformed,
transmitted or applied ;
(l)
“occupier” of a factory means the person who has ultimate control over the
affairs of the factory :
Provided that where the affairs of a factory are entrusted to a managing agent, such
agent shall be deemed to be the occupier of the factory ;
(m)
where work of the same kind is carried out by two or more sets of workers
working during different periods of the day, each of such sets is called a “relay”,
and the period or periods for which it works is called a “shift”; and
(n)
“prescribed” means prescribed by rules made by the 2[Provincial Government]
under this Act.
Ins. and subs. by Act No. XVI of 1973, s. 2.
Subs. by A. O., 1937.
3. References to time of day.___References to time of day in this Act are references___1[* * *]
[* *], to 3[*] Standard Time, which is five 3[* * *] hours ahead of Greenwich Mean Time, 1[*]
[*
*
*
*
*
*
*]
Provided that for any area 1[* * *] in which 3[*] Standard Time is not ordinarily observed the
[Provincial Government] may make rules___
(i)
specifying the area,
(ii)
defining the local mean time ordinarily observed therein, and
(iii)
permitting such time to be observed in all or any of the factories situated in the
area.
4. Seasonal factories.___(1) For the purposes of this Act, a factory which is exclusively engaged
in one or more of the following manufacturing processes, namely, cotton ginning, cotton or jute
pressing, the decortication of groundnuts, the manufacture of coffee, indigo, lac, rubber, sugar
(including gur) or tea, or any manufacturing process which is incidental to or connected with any of
the aforesaid processes, is a seasonal factory :
Provided that the 2[Provincial Government] may, by notification in the 2[official Gazette],
declare any such factory in which manufacturing processes are ordinarily carried on for more than one
hundred and eighty working days in the year, not to be a seasonal factory for the purposes of this Act.
(2) The 2[Provincial Government] may, by notification in the 2[official Gazette], declare any
specified factory in which manufacturing processes are ordinarily carried on for not more than one
hundred and eighty working days in the year and cannot be carried on except during particular seasons
or at times dependent on the irregular action of natural forces, to be a seasonal factory for the purposes
of this Act.
[5. Power to apply provisions applicable to factories to certain other places.___(1) The
Provincial Government may, by notification in the official Gazette, declare that all or any of the
provisions of this Act applicable to factories shall apply to any place wherein a manufacturing process
is being carried on or is ordinarily carried on whether with or without the use of power whenever
[five] or more workers are working therein or have worked therein any one day of the twelve months
immediately preceding.
Omitted by A. O., 1949, (w. e. f. 28th March, 1949).
Omitted and subs. by A. O., 1937.
Omitted and subs. by Act No. XVI of 1973, ss. 3 and 4.
Subs. by Act No. XVI of 1941, s. 2.
(2) A notification under sub-section (1) may be made in respect of any one such place or in
respect of any class of such places or generally in respect of all such places.
(3) Notwithstanding anything contained in clause (j) of section 2, a place, to which all or any
of the provisions of this Act applicable to factories are for the time being applicable in pursuance of a
declaration under sub-section (1), shall, to the extent to which such provisions are so made applicable
but not otherwise, be deemed to be a factory.]
6. Power to declare departments to be separate factories.___The 1[Provincial Government]
may, by order in writing, direct that the different departments or branches of a specified factory shall
be treated as separate factories for all or any of the purposes of this Act.
7. Power to exempt on a change in the factory.___Where the 1[Provincial Government] is
satisfied that, following upon a change of occupier of a factory or in the manufacturing process carried
on therein, the number of workers for the time being working in the factory is less than twenty and is
not likely to be twenty or more on any day during the ensuing twelve months, it may, by order in
writing, exempt such factory from the operation of this Act :
Provided that any exemption so granted shall cease to have effect on and after any day on which
twenty or more workers work in the factory.
[7A. Exemption from certain provisions of the Act.___The provisions of section 14, clause
(b) of sub-section (1) of section 15, sections 16, 17, 18, 21, 22, 23, 25 and sub-section (3) of section
33Q shall not apply in the first instance to any factory wherein not more than nineteen workers are
working or were working on any one day of the twelve months immediately preceding :
Provided that the Provincial Government may, by notification in the official Gazette, apply all
or any of the said provisions to any such factory or class of such factories.]
8. Power to exempt during public emergency.___In any case of public emergency the
[Provincial Government] may, by notification in the 1[official Gazette], exempt any factory from any
or all of the provisions of this Act for such period as 1[it] may think fit.
9. Notice to Inspector before commencement of work.___(1) Before work is begun in any
factory after the commencement of this Act, or before work is begun in any seasonal factory each
season, the occupier shall send to the Inspector a written notice containing___
(a)
the name of the factory and its situation,
(b)
the address to which communications relating to the factory should be sent,
(c)
the nature of the manufacturing processes to be carried on in the factory,
(d)
the nature and amount of the power to be used, 3[*]
Subs.by A. O., 1937.
Ins by Act No. XVI of 1973, s. 5.
Omitted by Act No. XIV of 1944, s. 2.
(e)
the name of the person who shall be the manager of the factory for the purposes
of this Act, 1[and
(f)
such other particulars as may be prescribed for the purposes of this Act].
[(1A) In respect of all factories which come within the scope of this Act for the first time on
the commencement of the Factories (Amendment) Ordinance, 1972 (XLII of 1972), the occupier shall
send a written notice to the Inspector containing particulars specified in sub-section (1) within thirty
days of such commencement.]
(2) Whenever another person is appointed as manager, the occupier shall send to the Inspector
a written notice of the change, within seven days from the date in which the new manager assumes
charge.
(3) During any period for which no person has been designated as manager of a factory under
this section, or during which the person designated does not manage the factory, any person found
acting as manager, or, if no such person is found, the occupier himself, shall be deemed to be the
manager of the factory for the purposes of this Act.
________
CHAPTER II
THE INSPECTING STAFF
10. Inspectors.___(1) The 3[Provincial Government] may, by notification in the 3[official
Gazette], appoint such persons as it thinks fit to be Inspectors for the purposes of this Act within such
local limits as it may assign to them respectively.
(2) The 3[Provincial Government] may, by notification as aforesaid, appoint any person to be a
Chief Inspector, who shall, in addition to the powers conferred on a Chief Inspector under this Act,
exercise the powers of an Inspector throughout the Province.
(3) No person shall be appointed to be an Inspector under sub-section (1) or a Chief Inspector
under sub-section (2) or, having been so appointed, shall continue to hold office, who is or becomes
directly or indirectly interested in a factory or in any process or business carried on therein or in any
patent or machinery connected therewith.
(4) Every District Magistrate shall be an Inspector for his district.
(5) The 3[Provincial Government] may also, by notification as aforesaid, appoint such public
officers as it thinks fit to be additional Inspectors for all or any of the purposes of this Act, within such
local limits as it may assign to them respectively.
(6) In any area where there are more Inspectors than one, the 3[Provincial Government] may,
by notification as aforesaid, declare the powers which such Inspectors shall respectively exercise, and
the Inspectors to whom the prescribed notices are to be sent.
Added by Act No. XIV of 1944, s. 2.
Ins. by Act No. XVI of 1973, s. 6.
Subs by A. O., 1937.
(7) Every Chief Inspector and Inspector shall be deemed to be a public servant within the
meaning of the Pakistan Penal Code (XLV of 1860) and shall be officially sub-ordinate to such
authority as the 1[Provincial Government] may specify in this behalf.
11. Powers of Inspector.___Subject to any rules made by the 1[Provincial Government] in this
behalf, an Inspector may, within the local limits for which he is appointed,___
(a)
enter, with such assistants (if any), being persons 2[in the service of the state] or
of any municipal or other public authority, as he thinks fit, any place which is,
or which he has reason to believe to be, used as a factory or capable of being
declared to be a factory under the provisions of section 5 ;
(b)
make such examination of the premises and plant and of any prescribed
registers, and take on the spot or otherwise such evidence of any persons as he
may deem necessary for carrying out the purposes of this Act ; and
(c)
exercise such other powers as may be necessary for carrying out the purposes
of this Act :
Provided that no one shall be required under this section to answer any question or give any
evidence tending to criminate himself.
12. Certifying surgeons.___(1) The 1[Provincial Government] may appoint such registered
medical practitioners as it thinks fit to be certifying surgeons for the purposes of this Act within such
local limits as it may assign to them respectively.
(2) A certifying surgeon may authorise any registered medical practitioner to exercise any of
his powers under this Act:
Provided that a certificate of fitness for employment granted by such authorised practitioner
shall be valid for a period of three months only, unless it is confirmed by the certifying surgeon himself
after examination of the person concerned.
Explanation.___In this section a “registered medical practitioner” means any person registered
[* * *] under any Act of 4[the 5[Federal] Legislature or any Provincial Legislature] (21 & 22 Vict., c
90.)] providing for the maintenance of a register of medical practitioners, and includes, in any area
where no such register is maintained, any person declared by the 1[Provincial Government], by
notification in the 6[official Gazette], to be a registered medical practitioner for the purposes of this
section.
Subs. by A. O., 1937.
Subs. by A. O., 1961, Art 2 and Sch. (w. e. f. 23 March 1956).
Omitted by the Federal Laws (Revision and Declaration) Ordinance, 1981 (Ordinance No. XXVII of 1981), s. 3 and Sch., 2.
Subs. by A.O., 1949 (w.e.f. 28th March, 1949).
Subs. by the Federal Adaptation of Laws Order, 1975 (President’s Order No. 4 of 1975), Art. 2 and Table (w.e.f. 28th July 1975).
Subs. by A.O., 1937 (w.e.f. 1st April, 1937).
[CHAPTER III
HEALTH AND SAFETY
13. Cleanliness.___(1) Every factory shall be kept clean and free from effluvia arising from and
drain, privy or other nuisance, and in particular,__
(a)
accumulation of dirt and refuse shall be removed daily by sweeping or by any
other effective method from the floors and benches of workrooms and from
stair-cases and passages and disposed of in a suitable manner ;
(b)
the floor of every workroom shall be cleaned at least once in every week by washing,
using disinfectant where necessary or by some other effective method ;
(c)
where the floor is liable to become wet in the course of any manufacturing
process to such extent as is capable of being drained, effective means of
drainage shall be provided and maintained ;
(d)
all inside walls and partitions, all ceilings, or tops, of rooms, and walls, sides
and tops or passages and stair-cases shall___
(e)
(i)
where they are painted or varnished, be repainted or revarnished at least
once in every five years ;
(ii)
where they are painted or varnished and have smooth impervious
surfaces, be cleaned at least once in every fourteen months, by such
methods as may be prescribed ;
(iii)
in any other case, kept whitewashed or colour washed and the
whitewashing or colour washing shall be carried out at least once in
every fourteen months ; and
the dates on which the processes required by clause (d) are carried out
shall be entered in the prescribed register.
(2) If, in view of the nature of the operations carried on in a factory it is not possible for the
occupier to comply with all or any of the provisions of sub-section (1), the Provincial Government
may, by an order, exempt such factory or class or description of factories from any of the provisions
of that sub-section and specify alternative methods for keeping the factory in a clean state.
14. Disposal of wastes and effluents.___(1) Effective arrangements shall be made in every
factory for the disposal of wastes and effluents due to the manufacturing process carried on therein.
(2) The Provincial Government may make rules prescribing the arrangements to be made under
sub-section (1) or requiring that the arrangements made in accordance with that sub-section shall be
subject to the approval of such authority as may be prescribed.
Subs. by the Labour Laws (Amdt.) Ordinance, 1972 (Ordinance No. IX of 1972), s. 2, Sch. 1 and 4. (w. e. f. 13th April 1972).
15. Ventilation and temperature.___(1) Effective and suitable provisions shall be made in
every factory for securing and maintaining in every work-room___
(a)
adequate ventilation by the circulation of fresh air, and
(b)
such temperature as will secure to workers therein reasonable conditions of
comfort and prevent injury to health, and in particular___
(i)
the walls and roofs shall be of such material and so designed that such
temperature shall not be exceeded but kept as low as practicable ;
(ii)
where the nature of the work carried on in the factory involves, or is
likely to involve, the production of excessively high temperature, such
adequate measures as are practicable, shall be taken to protect the
workers therefrom by separating the process which produces such
temperature from the work-room by insulating the hot parts or by other
effective means.
(2) The Provincial Government may prescribe a standard of adequate ventilation and
reasonable temperature for any factory or class or description of factories or parts thereof and direct
that a thermometer shall be provided and maintained in such place and position as may be specified.
(3) If it appears to the Provincial Government that in any factory or class or description of
factories excessively high temperature can be reduced by such methods as whitewashing, spraying or
insulating and screening outside walls or roofs or windows, or by raising the level of the roof, or by
insulating the roof either by an air space and double roof or by the use of insulating roof materials, or
by other methods, it may prescribe such of these or other methods to be adopted in the factory.
16. Dust and fume.___(1) In every factory in which, by reason of the manufacturing process
carried on, there is given off any dust or fume or other impurity of such a nature and to such an extent
as is likely to be injurious or offensive to the workers employed therein, effective measures shall be
taken to prevent its accumulation in any work-room and its inhalation by workers, and if any exhaust
appliance is necessary for this purpose, it shall be applied as near as possible to the point of origin of
the dust, fume or other impurity, and such point shall be enclosed so far as possible.
(2) In any factory no stationary internal combustion engine shall be operated unless the exhaust
is conducted into open air and exhaust pipes are insulated to prevent scalding and radiation heat, and
no internal combustion engine shall be operated in any room unless, effective measures have been
taken to prevent, such accumulation of fumes therefrom as are likely to be injurious to the workers
employed in the work-room.
17. Artificial humidification.___(1) The Provincial Government may, in respect of all factories
in which humidity of the air is artificially increased, make rules___
(a)
prescribing standards of humidification ;
(b)
regulating the methods used for artificially increasing the humidity of the air ;
(c)
directing prescribed test for determining the humidity of the air to be correctly
carried out and recorded ; and
(d)
Prescribing methods to be adopted for securing adequate ventilation and
cooling of the air in the work-rooms.
(2) In any factory in which the humidity of the air is artificially increased, the water used for
the purpose shall be taken from a public supply, or other source of drinking water, or shall be effectively
purified before it is so used.
(3) If it appears to an Inspector that the water used in a factory for increasing humidity which
is required to be effectively purified under sub-section (2) is not effectively purified, he may serve on
the Manager of the factory an order in writing specifying the measures which, in his opinion, should
be adopted, and requiring them to be carried out before a specified date.
18. Overcrowding.___(1) No work-room in any factory shall be overcrowded to an extent
injurious to the health of the workers employed therein.
(2) Without prejudice to the generality of the provisions of sub-section (1) there shall be
provided for every worker employed in a work-room___
(a)
at least three hundred and fifty cubic feet of space in the case of a factory in
existence on the date of the commencement of the Labour Laws (Amendment)
Ordinance, 1972 ; and
(b)
at least five hundred cubic feet of space in the case of a factory built after the
commencement of the Labour Laws (Amendment) Ordinance, 1972.
Explanation.___For the purpose of this sub-section no account shall be taken of a space which
is more than fourteen feet above the level of the floor of the room.
(3) If the Chief Inspector by order in writing so requires, there shall be posted in each workroom of a factory a notice specifying the maximum number of workers who may in compliance with
the provisions of this section be employed in the room.
(4) The Chief Inspector may, by order in writing, exempt, subject to such conditions as he may
think fit to impose, any work-room from the provisions of this section if he is satisfied that compliance
therewith in respect of such room is not necessary for the purpose of health of the workers employed
therein.
19. Lighting.___(1) In every part of a factory where workers are working or passing, there shall
be provided and maintained___
(a)
sufficient and suitable lighting, natural or artificial, or both ; and
(b)
emergency lighting of special points in work-room and passages to function
automatically in case of a failure of the ordinary electric supply system.
(2) In every factory all glazed windows and sky-lights used for the lighting of the work-room
shall be kept clean on both the outer and inner surfaces and free from obstruction as far as possible
under the rules framed under sub-section (3) of section 15.
(3) In every factory effective provisions shall, so far as is practicable, be made for the
prevention of___
(a)
glare either directly from any source of light or by reflection from a smooth or
polished surface ; and
(b)
the formation of shadows to such an extent as to cause eye strain or risk of
accident to any worker.
(4) The Provincial Government may prescribe standards of sufficient and suitable lighting for
factories or for any class or description of factories or for any manufacturing process.
20. Drinking water.___(1) In every factory effective arrangement shall be made to provide and
maintain at suitable points conveniently situated for all workers employed therein a sufficient supply
of whole-some drinking water.
(2) All such points shall be legibly marked “Drinking Water” in a language understood by the
majority of the workers and no such point shall be situated within twenty feet of any washing place,
urinal or latrine, unless a shorter distance is approved in writing by the Chief Inspector.
(3) In every factory wherein more than two hundred and fifty workers are ordinarily employed,
provision shall be made for cooling the drinking water during the hot weather by effective means and
for distribution thereof and arrangements shall also be made for___
(a)
the daily renewal of water if not laid on ; and
(b)
a sufficient number of cups or other drinking vessels, unless the water is being
delivered in an upward jet.
(4) The Provincial Government may, in respect of all factories or any class or description of
factories, make rules for securing compliance with the provisions of this section.
21. Latrines and urinals.___(1) In every factory___
(a)
sufficient latrines and urinals of prescribed types shall be provided conveniently
situated and accessible to workers at all times while they are in the factory ;
(b)
enclosed latrines and urinals shall be provided separately for male and female
workers ;
(c)
such latrines and urinals shall be adequately lighted and ventilated and no latrine
and urinal shall, unless specially exempted in writing by the Chief Inspector,
communicate with any work-room except through an intervening open space or
ventilated passage ;
(d)
all such latrines and urinals shall be maintained in a clean and sanitary condition
at all times with suitable detergents or disinfectants or with both ;
(e)
the floors and internal walls of the latrines and urinals and the sanitary blocks
shall, up to a height of three feet, be finished to provide a smooth polished
imperious surface ; and
(f)
washing facilities shall be provided near every sanitary convenience.
(2) The Provincial Government may prescribe the number of latrines and urinals to be provided
in any factory in proportion to the number of male and female workers ordinarily employed therein
and such further matters in respect of sanitation in the factories as it may deem fit.
22. Spittoons.___(1) In every factory there shall be provided, at convenient places, a sufficient
number of spittoons which shall be maintained in a clean and hygienic condition.
(2) The Provincial Government may make rules prescribing the type and the number of
spittoons to be provided and their location in any factory and such further matters as may be deemed
necessary relating to their maintenance in a clean and hygienic condition.
(3) No person shall spit within the premises of a factory except in the spittoons provided for
the purpose. A notice containing this provision and the penalty for its violation shall be prominently
displayed at suitable places in the premises.
(4) Whosoever spits in contravention of sub-section (3) shall be punishable with a fine not
exceeding two rupees.
23. Precaution against contagious or infectious disease.___(1) Each worker in a factory shall
be provided with a 'Hygiene Card' in which during the 1[months of January and July every year entries]
shall be recorded after examination by appointed factory doctor to the effect that the worker is not
suffering from any contagious or infectious disease. The fee of such an examination shall be fixed by
the Provincial Government and will be borne by the occupier or manager of the factory.
(2) If a worker is found to be suffering from any contagious or infectious disease on an
examination under sub-section (1), he shall not be appointed on work till he is declared free of such a
disease.
[23A. Compulsory vaccination and inoculation.___Each worker in a factory shall be
vaccinated and inoculated against such diseases and at such intervals as may be prescribed. The
expenses, if any, of such vaccination and inoculation shall be borne by the occupier or manager of the
factory.]
24. Power to make rules for provision of canteens.___(1) The Provincial Government may
make rules requiring that in any specified factory wherein more than two hundred and fifty workers
are ordinarily employed, an adequate canteen shall be provided for the use of the workers.
(2) Without prejudice to the generality of the foregoing power, such rules may provide for___
Subs. and ins. by Act No. XVI of 1973, ss. 7 and 8.
(a)
the date by which such canteen shall be provided ;
(b)
the standards in respect of construction, accommodation, furniture and other
equipment of the canteen ;
(c)
the foodstuffs to be served therein and the charges which may be made, therefor ;
(d)
representation of the workmen in the management of the canteens ;
(e)
enabling, subject to such conditions, if any, as may be specified, the power to
make rules under clause (c) to be exercised also by the Chief Inspector.
[24A. Welfare Officer.___In every factory wherein not less than five hundred workers are
ordinarily employed, the occupier or manager shall employ such number of welfare Officers, having
such qualifications, to perform such duties and on such terms and conditions as may be prescribed.]
25. Precautions in case of fire.___(1) Every factory shall be provided with such means of
escape in case of fire as may be prescribed.
(2) If it appears to the Inspector that any factory is not provided with the means of escape
prescribed under sub-section (1), he may serve on the manager of the factory an order in writing
specifying the measures which, in his opinion, should be adopted before a date specified in the order.
(3) In every factory the doors affording exit from any room shall not be locked or fastened so
that they can be easily and immediately opened from inside while any person is within the room, and
all such doors, unless they are of the sliding type, shall be constructed to open outwards or where the
door is between two rooms, in the direction of the nearest exit from the building and such door shall
not be locked or obstructed while work is being carried on in the room and shall at all times be kept
free from any obstruction.
(4) In every factory every window, door, or other exit affording means of escape in case of fire,
other than means of exit in ordinary use, shall be distinctively marked in a language understood by the
majority of the workers and in red letters of adequate size or by some other effective and clearly
understood sign.
(5) In every factory there shall be provided effective and clearly audible means of giving
warning in case of fire to every person employed therein.
(6) A free passage-way giving access to each means of escape in case of fire shall be maintained
for the use of all workers in every room of the factory.
(7) In every factory wherein more than ten workers are ordinarily employed in any place above
the ground floor, or explosive or highly inflammable materials are used or stored, effective measures
shall be taken to ensure that all the workers are familiar with the means of escape in case of fire and
have been adequately trained in the routine to be followed in such case.
(8) The Provincial Government may make rules prescribing in respect of any factory, or class
or description of factories, the means of escape to be provided in case of fire and the nature and amount
of fire fighting apparatus to be provided and maintained.
Ins. by Act No. XVI of 1973, s. 9.
26. Fencing of machinery.___(1) In every factory the following shall be securely fenced by the
safeguards of substantial construction which shall be kept in position while the parts of machinery
required to be fenced are in motion or in use, namely___
(a)
every moving part of a prime mover, and every fly wheel connected to a prime
mover ;
(b)
the headrace and tailrace of every water wheel and water turbine ;
(c)
any part of a stock-bar which protects beyond the head stock of a lathe ; and
(d)
unless they are in such position or of such construction as to be as safe to
every person employed in the factory as they would be if they were securely
fenced___
(i)
every part of an electric generator, a motor or rotary convertor ;
(ii)
every part of transmission machinery ; and
(iii)
every dangerous part of any machinery :
Provided that, in the case of dangerous parts of machinery that cannot be securely fenced by
reason of the nature of operation, such fencing may be substituted by other adequate measures, such
as___
(i)
devices automatically preventing the operation from coming into
contact with the dangerous parts ; and
(ii)
automatic stopping devices :
Provided further that, for the purpose of determining whether any part of machinery is in such
position or is of such construction as to be safe as aforesaid, account shall not be taken of any occasion
when it being necessary to make as examination of the machinery while it is in motion or, as a result
of such examination, to carry out any mounting or shipping of belts, lubrication or other adjusting
operation while the machinery is in motion, such examination or operation is made or carried out in
accordance with the provisions of section 27.
(2) Without prejudice to any other provisions of this Act relating to the fencing of machinery,
every set screw, belt and key on any revolving shaft, spindle wheel or pinion and all spur, worm and
other toothed or friction gearing in motion with which such worker would otherwise be liable to come
into contact, shall be securely fenced to prevent such contact.
(3) The Provincial Government may exempt, subject to such conditions as may be imposed,
for securing the safety of the workers, any particular machinery or part from the provisions of this
section.
(4) The Provincial Government may, by rules, prescribe such further precautions as it may
consider necessary in respect of any particular machinery or part thereof.
27. Work on or near machinery in motion.___(1) Where in any factory it becomes necessary
to examine any part of machinery referred to in section 26 while the machinery is in motion, or as a
result of such examination, to carry out any mounting or shipping of belts, lubrication or other adjusting
operation while the machinery is in motion, such examination or operation shall be made or carried
out only by a specially trained adult male worker wearing tight fitting clothing whose name has been
recorded in the register prescribed in this behalf and while he is so engaged, such worker shall not
handle a belt at a moving pulley unless the belt is less than six inches in width and unless the belt joint
is either laced or flush with the belt.
(2) No woman or child shall be allowed in any factory to clean, lubricate or adjust any part of
machinery while that part is in motion, or to work between moving parts or between fixed and moving
parts of any machinery which is in motion.
(3) The Provincial Government may, by notification in the official Gazette, prohibit, in any
specified factory or class or description of factories, the cleaning, lubricating or adjusting by any
person, of specified parts of machinery when those parts are in motion.
28. Employment of young persons on dangerous machines.___(1) No 1[child or adolescent]
shall work at any machine unless he has been fully instructed as to the dangers arising in connection
with the machine and the precautions to be observed and___
(a)
has received sufficient training in work at the machine, or
(b)
is under adequate supervision by a person who has thorough knowledge and
experience of the machine.
(2) This section shall apply to such machines as may be notified by the Provincial Government
to be of such a dangerous character that 1[children or adolescents] ought not to work at them unless
the foregoing requirements are complied with.
29. Striking gear and devices for cutting off power.___(1) In every factory___
(a)
suitable striking gear or other efficient mechanical appliances shall be provided
and maintained and used to move driving belts to and from fast and loose
pulleys which form part of the transmission machinery, and such gear or
appliances shall be so constructed, placed and maintained as to prevent the belt
from creeping back on the fast pulleys ;
(b)
driving belts when not in use shall not be allowed to rest or ride upon shafting
in motion.
(2) In every factory suitable devices for cutting off power in emergencies from running
machinery shall be provided and maintained in every work-room.
(3) In respect of factories in operation before the commencement of this Ordinance the
provisions of sub-section (2) shall apply only to work-rooms in which electricity is used for power.
Subs. by Act No. XVI of 1973, s. 10.
30. Self-acting machines. ___No traversing part of a self-acting machine in any factory and no
material carried thereon shall, if the space over which it runs is a space over which any person is liable
to pass whether in the course of his employment or otherwise be allowed to run on it outward or inward
traverse within a distance of eighteen inches from any fixed structure which is not part of the machine :
Provided that the Chief Inspector may permit the continued use of a machine installed before
the commencement of the Labour Laws (Amendment) Ordinance, 1972, which does not comply with
the requirements of this section on such conditions for ensuring safety as he may think fit to impose.
31. Casing of new machinery.___(1) In all machinery driven by power and installed in any
factory after the commencement of the Labour Laws (Amendment) Ordinance, 1972___
(a)
every set screw, belt or key on any revolving shaft, spindle, wheel or pinion
shall be so sunk, encased or otherwise effectively guarded as to prevent danger
; and
(b)
all spur, worm and other toothed or friction gearing which does not require
frequent adjustment while in motion shall be completely encased unless it is so
situated as to be as safe as it would be if it were completely encased.
(2) Whoever sells or lets on hire or, as agent of a seller or hirer, causes or procures to be sold
or let on hire, for use in a factory any machinery driven by power which does not comply with the
provisions of sub-section (1), shall be punishable with imprisonment, for a term which may extend to
three months, or with fine which may extend to five hundred rupees, or with both.
(3) The Provincial Government may make rules specifying further safe-guards to be provided
in respect of any other dangerous part of any particular machine or class or description of machines.
32. Prohibition of employment of women and children near cotton openers. ___ No woman
or child shall be employed in any part of a factory for pressing cotton in which a cotton opener is at work :
Provided that if the feed end of a cotton opener is in a room separated from the delivery end by
a partition extending to the roof or to such height as the Inspector may in any particular case specify
in writing, women and children may be employed on the side of the partition where the feed end is
situated.
33. Cranes and other lifting machinery.___(1) The following provisions shall apply in respect
of cranes and all other lifting machinery, other than hoists and lifts in any factory___
(a)
every part thereof, including the working gear, whether fixed or moveable, ropes
and chains and anchoring and fixing appliances shall be___
(i)
of good construction, sound material and adequate strength ;
(ii)
properly maintained ;
(iii)
thoroughly examined by a competent person at least once in every
period of twelve months, and a register shall be kept containing the
prescribed particulars of every such examination ;
(b)
no such machinery shall be loaded beyond the safe working load which shall be
plainly marked thereon ;
(c)
while any person is employed or working on or near the wheel tract of a
travelling crane in any place where he would be liable to be struck by the crane
effective measures shall be taken to ensure that the crane does not approach
within twenty feet of that place or come into accidental contact with live
electrical lines ;
(d)
limit switches shall be provided to prevent over running ; and
(e)
jib cranes, permitting the raising or lowering of the jib shall be provided with
an automatic safe load indicator or have attached to them a table indicating the
safe working load at corresponding inclinations of the jib.
(2) The Provincial Government may make rules in respect of any lifting machinery or class or
description of lifting machinery in factories___
(a)
prescribing requirements to be complied with in addition to those set out in this
section ; or
(b)
exempting from compliance with all or any of the requirements of this section,
where in its opinion such compliance is unnecessary or impracticable.
33A. Hoists and lifts.___(1) In every factory___
(a)
every hoist and lift shall be___
(i)
of good mechanical construction, sound material and adequate strength ;
(ii)
properly maintained, and shall be thoroughly examined by a competent
person authorised by the Chief Inspector in this behalf at least once in
every period of six months, and a register shall be kept containing the
prescribed particulars of every such examination of which a copy shall
be forwarded to the Chief Inspector ;
(b)
every hoistway and liftway shall be sufficiently protected by an enclosure fitted
with gates, and the hoist or lift and every such enclosure shall be so constructed
as to prevent any person or thing from being trapped between any part of the
hoist or lift and any fixed structure or moving part ;
(c)
the maximum safe working load shall be plainly marked on every hoist or lift,
and no load greater than such load shall be carried thereon ;
(d)
the cage of every hoist or lift used for carrying persons shall be fitted with a gate
on each side from which access is afforded to a landing ;
(e)
every gate referred to in clause (b) or clause (d) shall be fitted with interlocking
or other efficient device to secure that the gate cannot be opened except when
the cage is at the landing and that the cage cannot be moved unless the gate is
closed.
(2) The following additional requirements shall apply to hoists and lifts used for carrying
persons and installed or reconstructed in a factory after the commencement of the Labour Laws
(Amendment) 1972, namely :___
(a)
Where the cage is supported by rope or chain there shall be at least two ropes
or chains separately connected with the cage and balance weight, and each rope
or chain with its attachments shall be capable of carrying the whole weight of
the cage together with its maximum load ;
(b)
efficient devices shall be provided and maintained capable of supporting the
cage together with its maximum load in the event of breakage of the ropes,
chains or attachments ;
(c)
an efficient automatic device shall be provided and maintained to prevent the
cage from over-running.
(3) The Chief Inspector may permit the continued use of a hoist or lift installed in a factory
before the commencement of this Ordinance which does not fully comply with the provisions of subsection (1) upon such conditions for ensuring safety as he may think fit to impose.
(4) The Provincial Government may, if, in respect of class or description of hoist or lift, it is of
opinion that it would unreasonable to enforce any requirement of sub-sections (1) and (2), by order
direct that such requirements shall not apply to such class or description of hoist or lift.
33B. Revolving machinery.___(1) In every room in a factory in which the process of grinding
is carried on there shall be permanently affixed to, or placed near, each machine in use a notice
indicating the maximum safe working peripheral speed of every grind stone or abrasive wheel, the
speed of the shaft or spindle upon which the wheel is mounted and the diameter of the pully upon such
shaft or spindle necessary to secure such safe working peripheral speed.
(2) The speeds indicated in the notice under sub-section (1) shall not be exceeded.
(3) Effective measures shall be taken in every factory to ensure that the safe working peripheral
speed of every revolving vessel, cage basket, flywheel, pulley disc or similar appliance driven by
power is not exceeded.
33C. Pressure plant.___(1) If in any factory any part of the plant or machinery used in a
manufacturing process is operated at a pressure above atmospheric pressure, effective measures shall
be taken to ensure that safe working pressure of such part is not exceeded.
(2) The Provincial Government may make rules providing for the examination and testing of
any plant or machinery such as is referred to in sub-section (1) and prescribing such other safety
measures in relation thereto as may, in its opinion, be necessary in any factory or class or description
of factories.
33D. Floors, stairs and means of access.___In every factory___
(a)
all floors, stairs, passages and gangways shall be of sound construction and
properly maintained and where it is necessary to ensure safety, steps, stairs,
ladders, passages and gangways shall be provided with substantial handrails ;
(b)
there shall so far as is reasonably practicable be provided and maintained safe
means of access to every place at which any person is at any time required to
work ;
(c)
all places of work from which a worker may be liable to fall a distance
exceeding three feet and six inches shall be provided with fencing or there
suitable safeguards ; and
(d)
adequate provision shall be made for the drainage of floors in wet processes and
for the use of slatted stands and platforms.
33E. Pits, sumps, opening, in floors, etc.___(1) In every factory, every fixed vessel, sump, tank
pit or opening in the ground or in a floor which by reason of its depth, situation, construction or
contents, is or may be a source of danger, shall be either securely covered or securely fenced.
(2) The Provincial Government may, by order in writing, exempt, subject to such conditions as
may be imposed, any factory or class or description of factories in respect of any vessel sump, tank pit
or opening from compliance with the provisions of this section.
33F. Excessive weights.___(1) No person shall be employed in any factory to lift, carry or move
any load so heavy as to be likely to cause him injury.
(2) The Provincial Government may make rules prescribing the maximum weights which may
be lifted, carried or moved by adult men, adult women, adolescents and children employed in factories
or in any class or description of factories or in carrying on any specified process.
33G. Protection of eyes.___The Provincial Government may, in respect of any manufacturing
process carried on in any factory, by rules require that effective screens or suitable goggles shall be
provided for the protection of persons employed on, or in the immediate vicinity of, a process which
involves:___
(a)
risk of injury to the eyes from particles or fragments thrown off in the course
of the process, or
(b)
risk to the eyes by reason of exposure to excessive light or heat.
33. H. Powers to require specifications of defective parts or tests of stability.___If it appears
to the Inspector that any building or part of a building, or any part of the ways, machinery or plant in
a factory, is in such a condition that it may be dangerous to human life or safety, he may serve on the
Manager of the factory an order in writing, requiring him before a specified date___
(a)
to furnish such drawings, specifications and other particulars as may be
necessary to determine whether such building, ways, machinery or plant can be
used with safety, or
(b)
to carry out such tests as may be necessary to determine the strength or quality
of any specified parts and to inform the Inspector of the results thereof.
33I. Safety of building, machinery and manufacturing process.___(1) If it appears to the
Inspector that any building or part of a building or any part of the ways, machinery or plant or
manufacturing process in a factory is in such a condition that it is dangerous to human health or safety,
he may serve on the Manager of the factory an order in writing specifying the measures which, in his
opinion, should be adopted, and requiring them to be carried out before a specified date.
(2) If it appears to the Chief Inspector that the requisitions made under sub-section (1) are not
satisfactorily fulfilled thereby involving exposure of workers to serious hazards, he may serve on the
Manager of the factory an order in writing, containing a statement of the grounds of his opinion,
prohibiting until the danger is removed, the employment, in or about the factory or part thereof, of any
person whose employment is not in his opinion reasonably necessary for the purpose of removing the
danger.
(3) If it appears to the Inspector that the use of any building or part of a building or of any part
of the ways, machinery or plant or manufacturing process in a factory involves imminent danger to
human health or safety he may serve on the Manager of the factory an order in writing prohibiting,
until the danger is removed, the employment, in or about the factory or part thereof, of any person
whose employment is not in his opinion reasonably necessary for the purpose of removing the danger.
(4) Nothing in sub-section (2) or (3) shall be deemed to affect the continuance in the
employment of the factory of a person whose employment in or about the factory or part thereof is
prohibited under that sub-section.
33J. Power to make rules to supplement this Chapter.___The Provincial Government may
make rules requiring that___
(1) in any factory or in any class or description of factories, such further devices and measures
for securing the safety of the persons employed therein as it may deem necessary shall be adopted ;
and
(2) work on a manufacturing process carried on with the aid of power shall not be begun in any
building or part of a building erected or taken into use as a factory until a certificate of stability in the
prescribed form and signed by a person possessing the prescribed qualifications has been sent to the
Chief Inspector.
33K. Precautions against dangerous fumes.___(1) In any factory no person shall enter or be
permitted to enter any chamber, tank, vat, pit, pipe, flue or other confined space in which dangerous
fumes are likely to be present to such an extent as to involve risk of persons being overcome thereby,
unless it is provided with a manhole of adequate size or other effective means of egress.
(2) No portable electric light of voltage exceeding twenty-four volts shall be permitted in any
factory for use inside any confined space such as is referred to in sub-section (1) and, where the fumes
present are likely to be inflammable, a lamp or light other than of flame proof construction shall not
be permitted to be used in such confined space.
(3) No person in any factory shall enter or be permitted to enter any confined space such as is
referred to in sub-section (1) until all practicable measures have been taken to remove any fumes which
may be present and to prevent ingress of fumes and unless either—
(a)
a certificate in writing has been given by a competent person, based on a test
carried out by himself, that the space is free from dangerous fumes and fit for
persons to enter, or
(b)
the worker is wearing suitable breathing apparatus and a belt securely attached
to a rope, the free end of which is held by a person standing outside the confined
space.
(4) Suitable breathing apparatus, reviving apparatus and belts and ropes shall in every factory
be kept ready for instant use beside any such confined space as aforesaid which any person has entered,
and all such apparatus shall be periodically examined and certified by a competent person to be fit for
use ; and a sufficient number of persons employed in every factory shall be trained and practiced in
the use of all such apparatus and in the method of restoring respiration.
(5) No person shall be permitted to enter in any factory, any boiler furence, boiler flue, chamber,
tank, vat, pipe or other confined space for the purpose of working or making any examination therein
until it has been sufficiently cooled by ventilation or otherwise to be safe for persons to enter.
(6) The Provincial Government may make rules prescribing the maximum dimensions of the
mainholes referred to in sub-section (1) and may, by order in writing, exempt, subject to such
conditions as it may think fit to impose, any factory or class or description of factories from compliance
with any of the provisions of this section.
33L. Explosive or inflammable dust, gas, etc.___(1) Where in any factory any manufacturing
process produces dust, gas, fume or vapour of such character and to such extent as to be likely to
explode on ignition, all practicable measures shall be taken to prevent any such explosion by___
(a)
effective enclosure of the plant or machinery used in the process ;
(b)
removal or prevention of the accumulation of such dust, gas, fume or vapour ;
(c)
exclusion or effective enclosure of all possible sources of ignition.
(2) Where in any factory the plant or machinery used in a process such as is referred to in subsection (1) is not so constructed as to withstand the probable pressure which such an explosion as
aforesaid would produce, all practicable measures shall be taken to restrict the spread and effects of
the explosion by the provision in the plant or machinery of chokes, Baffles, vents or other effective
appliances.
(3) Where any part of the plant or machinery in a factory contains any explosive or inflammable
gas or vapour under pressure greater than atmospheric pressure, that part shall not be opened except in
accordance with the following provisions, namely :___
(a)
before the fastening of any joint of any pipe connected with the part of the
fastening of the cover of any opening into the part is loosened.
any flow of the gas or vapour into the part or any such pipe shall be effectively
stopped by a stop-valve or other means ;
(b)
before any such fastening as aforesaid is removed, all practicable measures shall
be taken to reduce the pressure of the gas or vapour in the part or pipe to
atmospheric pressure ;
(c)
where any such fastening as aforesaid has been loosened or removed, effective
measures shall be taken to prevent any explosive or inflammable gas or vapour
from entering the part or pipe until the fastening has been secured or, as the case
may be, securely replaced :
Provided that the provisions of this sub-section shall not apply in the case of plant or machinery
installed in the open air.
(4) No plant, tank or vessel which contains or has contained any explosive or inflammable
substance shall be subjected in any factory to any welding, brazing, soldering or cutting operation
which involves the application of heat or to any drilling or other operation which is likely to create
heat or sparks, unless adequate measures have first been taken to remove such substance and any fumes
arising therefrom or to ren
The text continues in the official source.
